Salvajor S914, P914 Installation & Operating Instructions Manual

Salvajor Scrap CollectorsTM

Model S914 & Model P914

Scrapping, Pre-flushing and Food Waste Collecting Systems

Installation & Operating

Scrap Collector
Model S914

2 Additional Parts Contents
3 Fabricator Instructions & Installation
4 Plumbing & Electrical
5 Operating Instructions
6 How it Works & Troubleshooting
7 Warranty
8 General Terms and Conditions of Sale

ALL INSTALLATIONS SHOULD BE MADE IN ACCORDANCE WITH
LOCAL AND NATIONAL PLUMBING AND ELECTRICAL CODES.

Pot/Pan Scrap Collector
Model P914

INSTRUCTIONS

U.S. Pat. No. 7,815,134

FOR PRODUCT/WARRANTY REGISTRATION

Go to www.salvajor.com

•

Click on SUPPORT at the top of home page

•

Click on PRODUCT REGISTRATION

•

#

1 in FOOD WASTE SOLUTIONS

The Salvajor Company 4530 East 75th Terrace Kansas City, Missouri 64132-2081, USA

1-888-SALVAJOR FAX: [phone]

www.salvajor.com Email: [e-mail] [e-mail]

Manufacturers of Commercial Food Waste Disposing Systems since 1944

Additional Parts Contents

Collector Top Box

(May ship separate)

ADDITIONAL

PARTS

Installation &
Operating Manual

X 4

X 12

Collector

Hardware

X 4

X 12

X 12

Gusher Plate

Gasket

Hose Clamp

Flexible
Recirculation Hose

X 12

Collector Hardware

Hose Clamps

Gusher Plate

and Gasket

Hose Clamp

Flexible

Recirculation

Hose

2

Fabricator Instructions

243/4"

(

62.87

)

22

1

/4"

(

56.52

)

24” min.

Dish rack space

Dish machine

Upon request, the Collector top may be shipped separately to a fabricator for welding to table.

243/4"

(

)

62.87

1

22

/4"

(

)

56.52

Use the above dimensions for the table cut out. Place the
top

to the underside of the table for welding. Attention: When attaching the Scrap Collector or Pot/Pan Scrap

Dish machine

24” min.

Dish rack space

TABLE CUTOUT

DETAIL FOR MODEL

S914

ONLY

1

/4"

22

(

)

OR

56.52

Scrap Collector (S914) top

361/2"

(

92.78

)

or the

Pot/Pan Scrap Collector (P914)

Dish machine

24” min.

Dish rack space

TABLE CUTOUT

DETAIL FOR MODEL

P914

ONLY

Collector top to the table, make sure the top is mounted in the table with the recirculated water opening (water
plume) on the same side as the dishmachine. Leave a minimum of 24 inches between the Collector and the
loading end of the dishmachine to allow space for the dish rack.

Installation

Attach Collector tank to the Collector top. The tank must be oriented

GUSHER PLATE

GASKET

FLEXIBLE

RECIRCULATION

HOSE

HOSE CLAMP

HOSE
CLAMP

COLLECTOR
HARDWARE

X 4

X 12

X 12

Collector Top

Collector Tank

ADJUSTABLE LEGS

All Collector parts/hardware shown are located in the
“additional parts” carton inside the Collector tank box.

so that the recirculation plumbing is properly aligned. The control,
pump and incoming water will be on the opposite side of the recircula­tion hose. Connect gusher plate and flexible recirculation hose to the
Collector. Adjust the legs until they extend to the floor. Note: Be-

fore installation of the Collector tank to the top, confirm that the
pre-installed gasket is affixed to the bottom of the Collector top.

CONTROL

PUMP

FLEXIBLE

RECIRCULATION HOSE

STOP!

If you have any questions about this installation call 1-888-SALVAJOR for installation advice.

The control and sensor can be mounted on either side of the Collector
with existing fasteners, mounting holes and wiring to accommodate
dish flow to the left or to the right. It is not necessary to disconnect
factory-installed wiring.

The control and sensor should always face the operator.

If necessary, the control can be mounted remotely. Additional
field wiring and hardware will be necessary. Contact service for
installation advice.

3