Salvajor Commercial Disposers
For All Models: 75, 100, 150, 200, 300, 500, 750
Models 300-750
Models 75-200
2Typical Installations
& Installation of Cone Bowl or Sink Collar
3 |
Attaching Disposer to Cone Bowl or Sink Collar |
|
& Plumbing |
4 |
Electrical |
|
|
5 |
Operating Instructions & Troubleshooting |
|
|
6 |
Warning & Safety Instructions |
ALL INSTALLATIONS SHOULD BE MADE IN ACCORDANCE WITH LOCAL AND NATIONAL PLUMBING AND ELECTRICAL CODES.
FOR PRODUCT/WARRANTY REGISTRATION
•Go to www.salvajor.com
•Click on SUPPORT at the top of homepage
•Click on PRODUCT REGISTRATION
#1 in FOOD WASTE SOLUTIONS
INSTRUCTIONS |
Operating & Installation |
The Salvajor Company 4530 East 75th Terrace |
Kansas City, Missouri 64132-2081, USA |
|
1-888-SALVAJOR |
FAX: 1-800-832-9373 |
|
www.salvajor.com Email: sales@salvajor.c om |
ser vice@salv ajor.com |
Manufactu rers of Commer cial Food Was te Dispos ing Systems since 1944
Made in the U.S.A.
Typical Installations
1/2" PLUMBING |
VACUUM |
|
BREAKER |
|
OPTIONAL |
|
|
CONE OR SINK |
WATER |
|
|
PRE-RINSE |
|
|
INLET |
INCOMING POWER |
|
|
|
|
|
|
|
|
|
|
|
|
|
(P) |
|
|
1/2" PLUMBING |
VACUUM |
SOLENOID VALVE |
|
(PP) |
|
|
|
BREAKER |
WITH FLOW CONTROL |
|
|
|
|
|
|
1/2" VALVE |
INCOMING WATER |
|
OPTIONAL |
|
|
|
(NF) |
3/4" PLUMBING |
|
REMOTE |
|
|
|
|
REDUCED TO 1/2" |
|
START/STOP |
|
|
|
|
2" DRAIN (models 75-200) |
|
CONTROL |
|
|
|
|
2" OR 3" DRAIN (models 300-750) |
|
|
CONE |
WATER |
|
|
1/2" VALVE |
WITH (P) OR (PP) |
|
|
|
|
|
|||
|
INLET |
|
|
|
(NF) |
INCOMING WATER |
|
|
|
|
|
|
3/4" PLUMBING |
|
|
|
|
|
|
REDUCED TO 1/2" |
2" DRAIN |
|
INCOMING POWER |
|
|
|
|
(models 75-200) |
CONTROL |
1/2" PLUMBING |
VACUUM |
SOLENOID VALVE |
||
2" OR 3" DRAIN |
|
|||||
|
|
|
BREAKER |
WITH FLOW CONTROL |
||
(models 300-750) |
|
|
|
|
|
|
|
|
OPTIONAL |
|
|
1/2" VALVE |
INCOMING WATER |
|
|
SHORT TOP |
|
|
||
|
|
HOUSING |
SINK |
|
(NF) |
3/4" PLUMBING |
REDUCED TO 1/2"
Model s 300 through |
|
WATER |
750 furnis hed with |
|
INLET |
2" DRAIN |
|
|
singl e suppo rt leg. |
|
|
(models 75-200) |
INCOMING POWER |
|
|
2" OR 3" DRAIN |
|
|
(models 300-750) |
CONTROL |
|
OPTIONAL |
|
|
|
|
|
|
SHORT LEG |
Installation of CONE BOWL or SINK COLLAR
CONE ASSEMBLY
1. Cut a hole in the counter top using the appropriate table cutout dimensions listed below.
|
Application |
Cutout Size |
|
|
12" Cone Bowl |
12 7⁄8" Diameter |
|
|
|
|
|
|
15" Cone Bowl |
15 7⁄8" Diameter |
|
|
|
|
|
|
18" Cone Bowl |
18 7⁄8" Diameter |
|
|
|
|
|
2. Place the large open end of the cone bowl against the underside of the counter top and weld the flange. Weld all the way around and then buff smooth for a watertight, sanitary installation.
SINK COLLARS:
6 1⁄2" Sink Collar #65
1.If necessary, cut a 6 5/8" DIAMETER hole in the center of the bottom of the sink.
2.Place the adaptor against the underside of the sink and weld all the way around.Buff smooth for a watertight, sanitary installation.
3 1⁄2" Sink Collar #70
1.Apply caulking compound around the sink hole (TOP SIDE).
2.Insert the stainless steel adaptor in the sink hole.
3.Place the gasket over the stainless steel adaptor (UNDER SINK).
4.Place the hex metal washer over the stainless steel adaptor, up against the gasket.
5.Place the sink collar with O-ring inserted over the stainless steel adaptor, up against the hex metal washer.
6.Slip the spring steel snap ring over the bottom of the stainless steel adaptor and slide up until it snaps into the groove in the stainless steel adaptor.
7.Screw the hex head bolts out of the sink collar and up against the hex metal washer tight enough to firmly set the assembly.
8.The disposer rubber adaptor fits over the sink collar and bands to the sink collar.
WARNING: Never put your hand thru the Sink Collar after being installed as injury is possible.
#65 SINK COLLAR |
|
#70 SINK COLLAR |
||
SINK |
LARGE RUBBER |
|
SINK |
RUBBER STOPPER |
|
STOPPER (LRS) |
|
|
(5088) |
|
|
|
|
|
|
|
|
|
S.S. SINK |
|
|
|
|
ADAPTOR |
|
|
|
31/2" - 4" |
(S5028) |
|
|
|
|
|
|
|
|
SINK |
|
|
|
|
OPENING |
|
|
|
|
HEX METAL |
GASKET |
|
|
|
WASHER |
|
|
65/8" |
|
(S5028F) |
(S5028G) |
|
|
S.S. HEX HEAD |
O-RING |
|
|
SINK OPENING |
|
||
|
|
(568237) |
||
|
|
|
BOLTS (997031) |
|
WELD IN |
|
2 |
SPRING STEEL SNAP |
SINK COLLAR |
SINK COLLAR |
|
|||
|
(70C) |
|||
(65) |
|
RING RETAINER |
|
|
|
|
|
(S5028LS) |
|