TEMINOX®
G
Operation
Germany
Germany
Internet: www.saacke.com
TEMINOX®
G
0-0124-4267b-02
2021-06-22
1 Operation
1.1 Preparing the Heat Generator
Prepare the heat generator (e. g. boiler, combustion chamber) for operation. Heed
the instructions for the heat generator in the manufacturer's documentation.
1.2 Preparing the Burner
Supply the burner with the fuel and the ignition medium
the fuel supply system in the manufacturer's documentation.
1.3 Starting the Burner
Select the fuel and switch the burner on. Follow the instructions in the
manufacturer's documentation for the burner control system.
Wait until the end of the purge phase.
Monitor the sequence of operations and the ignition cycle.
1
. Heed the instructions for
If a fault is signaled: Refer to chapter 1.6.
Starting the heat generator (when the plant is cold)
Start the heat generator when the plant is cold. Heed the instructions for the heat
generator in the manufacturer's documentation.
1.4 Controlled Operation
Controlled operation is performed automatically. No manual operation is required.
Exception: Firing rate controller is set to "Manual". Follow the instructions in the
manufacturer's documentation on the burner control system.
If a fault is signaled: Refer to chapter 1.6.
In case of danger:
Press the "Emergency Stop button" of the plant and interrupt the fuel supply!
1.5 Switching Off the Burner
Run the burner to low-load position. Follow the instructions in the manufacturer's
documentation for the burner control system.
1
For burners with ignition medium
SAACKE GmbH
Südweststraße 13
28237 Bremen
Switch off the burner. Follow the instructions in the manufacturer's documentation
for the burner control system.
SAACKE GmbH
Postfach 210261
28222 Bremen
Tel.: +49 421 64 95 0
Fax: +49 421 64 95 5224
E-Mail: info@saacke.de
Technical Documentation
0-0124-4267b-02
2021-06-22 1 / 4
Functi
onal Schematic TEMINOX®
G
For Maintenance
Also follow the instructions in the chapter entitled "Maintenance/Cleaning" in the
operating instructions.
For Prolonged Shutdown Time
Interrupt the fuel supply and the supply with the ignition medium as well
example manual shut-off valves in the supply system). Follow the instructions in
the manufacturer's documentation for the corresponding supply systems.
1.6 Service Interruption due to Fault
Note
This section describes only the steps relevant for the burner. Follow the
instructions in the manufacturer's documentation on the fuel supply system and
burner control system as well as the other subsystems in the plant.
2
(for
For Immediate Restart without Troubleshooting and Elimination of Faults:
Acknowledge the fault. Follow the instructions in the manufacturer's documentation
for the burner control system.
Reset the burner control system. Follow the instructions in the manufacturer's
documentation for the burner control system.
Follow the instructions in chapters 1.3 to 1.4.
If Troubleshooting is Necessary:
Secure the burner to prevent it from being restarted.
Interrupt the fuel supply and the supply with the ignition medium
instructions in the manufacturer's documentation for the corresponding supply
systems.
3
. Follow the
Eliminate the fault (refer to the chapter "Troubleshooting" and
"Maintenance/Cleaning" in the operating instructions). If in doubt, contact the
service personnel.
Acknowledge the fault. Follow the instructions in the manufacturer's documentation
for the burner control system.
Reset the burner control system. Follow the instructions in the manufacturer's
documentation for the burner control system.
Follow the instructions in chapters 1.1 to 1.4.
2
For burners with ignition medium
3
For burners with ignition medium
2 / 4
Technical Documentation
0-0124-4267b-02 2021-06-22
TEMINOX®
G Functional Schematic
TMX217
2 Functional Schematic
Fig. 1: Functional schematic for gas operation
2021-06-22
Technical Documentation
0-0124-4267b-02 3 / 4
Functional Schematic
TEMINOX®
G
Device number 4 Designation
A --- Main fuel inlet (gas)
B --- Combustion air inlet
C --- Heat generator
1a/1b 10 A 1 / External5
2 28 F 2 / External5 Gas pressure monitor (L)
3 28 F 3 / External5 Gas pressure monitor (H)
4 External Emergency stop button for fuel supply system
5a ---
5b ---
6 --- Stabilizing disk retract mechanism
7 40 B 1 Flame scanner
8* --- Manual shut-off fitting
9* 2 Y 1 Rapid shut-off valve 1 for ignition medium
10* 2 Y 2 Rapid shut-off valve 2 for ignition medium
11 2 T 1 Ignition transformer
12 --- Combustion air fan
13 17 F 2 Pressure monitor (L) for combustion air
14 --- Air control dampers
15 External Speed pickup (optional)
16** --- Flue gas actuator for “Mini-Rezi“
* For sizes 50 and 70, ignition is direct and electrical in both oil operation and gas
operation. Therefore these components are not installed on these burners.
Rapid shut-off valves 1 and 2 (double solenoid valve) for main
fuel gas
TEMINOX GL: Drive unit oil / gas
TEMINOX G: Gas control damper
Burner head variant C03: Gas control damper for controlled
primary gas
Burner head variant C01: Optional gas control damper for
controlled primary gas
Burner head variant C02: Not installed
** Optional component
4
Cp. Electrical Documentation
5
Depending on the order, this component may be part of the gas valve train or part of the burner. If it has
been ordered as part of the gas valve train, it will be connected externally.
Technical Documentation
4 / 4
0-0124-4267b-02 2021-06-22
Loading...