sa sa ak630 Service Manual

0 (0)

n AMPLIFIER SECTION

RMS output power

THD 10%, both channels driven

1 kHz

(Low channel) 75 W per channel (5 Ω)

10 kHz

(High channel) 70 W per channel (5 Ω)

80 Hz

(Subwoofer channel) 160 W (8 Ω)

Total power output 450 W

For GC only

PMPO 4000 W

n FM/AM TUNER, TERMINALS SECTION

Preset station FM 15 stations

AM 15 stations

Frequency Modulation (FM)

Frequency range

87.50 - 108.00 MHz (50 kHz steps)

Sensitivity 2.5 µV (IHF)

S/N 26 dB 2.2 µV

ntenna terminal(s) 75 Ω (unbalanced)

mplitude Modulation (AM)

Frequency range

For GC only 522 - 1629 kHz (9 kHz steps)

520 - 1630 kHz (10 kHz steps)

For GN only 522 - 1629 kHz (9 kHz steps)

Sensitivity

S/N 20 dB (at 999 kHz) 560 µV/m

rights reserved. Unauthorized copying and

distribution is a violation of law.

SA-AK630GC

SA-AK630GN

Colour

(S)... Silver Type

udio performance (Amplifier)

Input sensitivity/Input impedance

ux 250 mV,14.7 kΩ

Phone jack

Terminal Stereo, 3.5 mm jack

n CASSETTE DECK SECTION

Track system 4 track, 2 channel

Heads

Record/playback Solid permalloy head

Erasure Double gap ferrite head

Motor DC servo motor

Recording system AC bias 100 kHz

Erasing system AC erase 100 kHz

Tape speed 4.8 cm/s

Overall frequency response (+3 dB, -6 dB at DECK OUT)

NORMAL 35 Hz - 14 kHz

S/N ratio 50 dB (A weighted)

Wow and flutter 0.18 % (WRMS)

Fast forward and rewind time Approx. 120 seconds with

C-60 cassette tape

n DISC SECTION

Discs played [8 cm or 12 cm]

(1) CD-Audio (CD-DA)

(2) CD-R/RW (CD-DA, MP3 formatted disc)

(3) MP3

Bit rate

MP3 32 kbps - 320 kbps

CD Stereo System

Specifications

ORDER NO. MD0501043C3

Sampling frequency

MP3 32 kHz, 44.1 kHz, 48 kHz

CD 44.1 kHz

Decoding 16 bit linear

Digital filter 8fs

D/A converter MASH (1 bit DAC)

Pickup

Wavelength 780 nm

Beam Source Semiconductor laser

udio output (Disc)

Number of channels 2(Stereo)(FL,FR)

n GENERAL

Power Supply

For GC only AC 220-240V, 50/60Hz

For GN only AC 230-240V, 50Hz

Power consumption 260 W

1 Before Repair and Adjustment

2 Protection Circuitry

3 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

4 Handling the Lead-free Solder

4.1. About lead free solder (PbF)

5 Handling Precautions For Traverse Deck

6 Precaution of Laser Diode

7 Accessories

8 Operation Procedures

9 Disassembly and Assembly of Main Component

9.1. Disassembly flow chart

9.2. Gear for servicing (jig) Information

9.3. Disassembly of Top Cabinet

9.4. Disassembly of CD Lid

9.5. Disassembly of Rear Panel

9.6. Disassembly of CD Mechanism Unit

9.7. Disassembly of Main P.C.B.

9.8. Disassembly of Sub-Power P.C.B.

9.9. Disassembly of Power P.C.B.

9.10. Disassembly of Transformer P.C.B.

9.11. Disassembly of Front Panel Unit

9.12. Disassembly of Deck Mechanism Unit

9.13. CD Mechanism Main Component Replacement

Procedures

9.14. Replacement for the pinch roller ass 馳 and head block

Power consumption in standby

mode

0.7 W

Dimensions (W x H x D) 250 x 330 x 341 mm

Mass 7.1 kg

Operating temperature range +5 to +35°C

Operating humidity range 5 to 90% RH (no condensation)

n SYSTEM

SC-AK630 (GC) Music center: SA-AK630 (GC)

Speaker: SB-AK630 (GC)

Subwoofer: SB-WAK630 (GC)

SC-AK630 (GN) Music center: SA-AK630 (GN)

Speaker: SB-AK630 (GC)

Subwoofer: SB-WAK630 (GC)

Notes:

1. Specifications are subject to change without notice. Mass and

dimensions are approximate.

2. Total harmonic distortion is measured by the digital spectrum

analyzer.

9.15. Replacement for the Deck motor ass 馳, capstan belt A,

capstan belt B and winding belt

9.16. Replacement for the cassette lid ass 馳

9.17. Rectification for tape jam problem

10 Checking for major P.C.Bs

10.1. Checking of Main P.C.B.

10.2. Checking of Transformer P.C.B.

10.3. Checking of Panel, Deck & Deck Mechanism P.C.B.

10.4. Checking of Power P.C.B.

11 Self-Diagnostic Function

11.1. Self-diagnostic display

11.2. How to enter the Self-Diagnostic Function

11.3. Cassette Mechanism Test (For error code H01, H02, H03,

F01)

11.4. CD Mechanism Test (F15, F26, F16, F17, F27, F28, F29,

F30, H15 & H16)

11.5. To clear all Error code

11.6. To exit from Self-Diagnostic function

11.7. Power Amplifier Failure (F61)

11.8. Description of Error Code

12 CD Test Mode Function

12.1. How to set CD test mode

12.2. CD Automatically Adjustment result indication

12.3. CD Mecha Aging Test Mode (CR20)

12.4. Micon ROM Checksum and Version Display Mode

13 Measurements and Adjustments

13.1. Cassette Deck Section

CONTENTS

Page Page

SA-AK63 0GC / SA-AK63 0GN

13.2. Tuner Section 49

13.3. Alignment Points

14 Block Diagram

15 Voltage Measurement

16 Schematic Diagram

16.1. (A) CD Servo Circuit

16.2. (B) Main (Tuner) Circuit

16.3. (B) Main Circuit

16.4. (C) Panel Circuit

16.5. (D) Transformer Circuit

16.6. (E) CD Detect Circuit, (F) Spindle Position Circuit, (G) CD

Loading Circuit & (L) Sub-Power Circuit

16.7. (H) Power Circuit

16.8. (I) Deck Circuit & (J) Deck Mechanism Circuit

17 Printed Circuit Board

17.1. (A) CD Servo P.C.B.

17.2. (B) Main P.C.B.

17.3. (C) Panel P.C.B.

17.4. (D) Transformer P.C.B.

17.5. (E) CD Detect P.C.B., (F) Spindle Position P.C.B., (G) CD

Loading P.C.B. & (K) Tuner Pack P.C.B.

17.6. (H) Power P.C.B. & (L) Sub-Power P.C.B.

17.7. (I) Deck P.C.B. & (J) Deck Mechanism P.C.B.

18 Wiring Connection Diagram

19 Illustration of IC 痴, Transistors and Diodes

20 Terminal Function of IC 痴

20.1. IC7002 (MN6627953HB) Servo processor/ Digital signal

processor/ Digital filter/ D/A converter

20.2. IC7003 (AN8739SBTE2) Focus coil/ Tracking coil/

Traverse motor/ Spindle motor drive

20.3. IC2801 (C2CBJG000561) System Microprocessor

21 Troubleshooting Guide

22 Parts Location and Replacement Parts List

22.1. Deck Mechanism (RAA4502-S)

22.2. CD Loading Mechanism (RD-DAC026-S)

22.3. Cabinet

100

22.4. Electrical Parts List

102

22.5. Packing Materials & Accessories Parts List

111

22.6. Packaging

112

SA-AK63 0GC / SA-AK63 0GN

1 Before Repair and Adjustment

Disconnect AC power, discharge Power Supply Capacitors C5820 and C5840 through a 10Ω, 5W resistor to ground.

DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.

After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

For GC only

Current consumption at AC 220-240V, 50/60 Hz in NO SIGNAL mode (volume min at CD mode) should be ~350mA.

For GN only

Current consumption at AC 230-240V, 50 Hz in NO SIGNAL mode (volume min at CD mode) should be ~350mA.

2 Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed:

No sound is heard when the power is turned on.

Sound stops during a performance.

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are

“shorted”, or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.

If this occurs, follow the procedure outlines below:

1. Turn off the power.

2. Determine the cause of the problem and correct it.

3. Turn on the power once again after one minute.

Note :

When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

SA-AK63 0GC / SA-AK63 0GN

3 Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called

Electrostatica lly Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field- effect transistors and

semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage

caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminium foil, to prevent electrostatic charge build up or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder remover device. Some solder removal devices not classified as “anti- static (ESD protected)” can

generate electrical charge to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminium foil or

comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize body motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing

together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to

damage an ES device).

4 Handling the Lead-free Solder

4.1. About lead free solder (PbF)

Distinction of PbF P.C.B.:

P.C.B.s (manufacture d) using lead free solder will have a PbF stamp on the P.C.B.

Caution:

Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please

use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700 ± 20°F (370 ±

10°C).

Pb free solder will tend to splash when heated too high (about 1100°F/600°C).

W hen soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the

soldering points with the Pb free solder until it melts enough.

SA-AK63 0GC / SA-AK63 0GN

5 Handling Precautions For Traverse Deck

The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of

clothes or human body.

So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).

Handling of traverse deck (optical pickup)

1. Do not subject the traverse deck (optical pickup) to static electricity as it is extremely sensitive to electrical shock.

2. To prevent the breakdown of the laser diode, an antistatic shorting pin is inserted into the flexible board (FFC board).

3. Take care not to apply excessive stress to the flexible board (FFC board). When removing or connecting the short pin, finish

the job in as short time as possible.

4. Do not turn the variable resistor (laser power adjustment). It has already been adjusted.

Grounding for electrostatic breakdown prevention

1. Human body grounding

Use the anti-static wrist strap to discharge the static electricity from your body.

2. Work table grounding

Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is place, and ground the

sheet.

Caution :

The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the

traverse deck (optical pickup).

Caution when replacing the Traverse Deck

The traverse deck has a short point shorted with solder to protect the laser diode against electrostatics breakdown. Be sure to

remove the solder from the short point before making connections.

SA-AK63 0GC / SA-AK63 0GN

6 Precaution of Laser Diode

Caution :

This product utilizes a laser diode with the unit turned "ON", invisible laser radiation is emitted from the pick up lens.

Wavelength : 780 nm

Maximum output radiation power from pick up : 100 µW/VDE

Laser radiation from pick up unit is safety level, but be sure the followings:

1. Do not disassemble the optical pick up unit, since radiation from exposed laser diode is dangerous.

2. Do not adjust the variable resistor on the pick up unit. It was already adjusted.

3. Do not look at the focus lens using optical instruments.

4. Recommend not to look at pick up lens for a long time.

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

n Use of Caution Labels

SA-AK63 0GC / SA-AK63 0GN

7 Accessories

Remote Control

FM Antenna

AC Cord (For GN only)

AC Cord (For GC only)

AM Loop Antenna

SA-AK63 0GC / SA-AK63 0GN

8 Operation Procedures

SA-AK63 0GC / SA-AK63 0GN

9 Disassembly and Assembly of Main Component

“ATTENTION SERVICER”

Some chassis components may have sharp edges. Be careful when disassemblin g and servicing.

1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main

components.

2. For reassembly after operation checks or replacement, reverse the respective procedures.

Special reassembly procedures are described only when required.

3. Select items from the following index when checks or replacement are required.

4. Refer to the Parts No. on the page of “Parts Location and Replacement Parts List” (Section 22), if necessary.

9.1. Disassembly flow chart

The following chart is the procedure for disassemblin g the casing and inside parts for internal inspection when carrying out the

servicing.

To assemble the unit, reverse the steps shown in the chart as below.

SA-AK63 0GC / SA-AK63 0GN

9.2. Gear for servicing (jig) Information

1. This unit has a gear which is used for checking items (Open/Close of disc tray, up/down operation of traverse unit by manually)

when servicing.

2. For preparation of gear (for servicing), perform the procedures as follows.

3. In case of re-servicing the same set, the “gear for servicing” may has been taken off because it has been used. The “gear for

servicing” must be stored.

Remove the gear provided with mecha cover as shown below.

Insert the hexagonal screwdriver (2mm) into the gear, and then project the tip of screwdriver for 1~ 2 mm in length.

SA-AK63 0GC / SA-AK63 0GN

Step 1 Remove 2 screws at each side and 5 screws at rear

panel.

Step 2 Lift up both sides of the top cabinet, push the top

cabinet towards the rear and remove the top cabinet.

Opening the disc tray automatically (Using Power

Supply)

Step 1 Connect the AC power cord.

Step 2 Press the POWER button to power up the main unit.

Step 3 Press the OPEN/CLOSE button, the disc tray will open

automatically .

Step 4 Release the 2 claws, and then remove the CD Lid.

Step 5 Press the OPEN/CLOSE button, the disc tray will close.

9.3. Disassembly of Top Cabinet

9.4. Disassembly of CD Lid

(The CD changer unit can be removed after the CD Lid is removed)

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

SA-AK63 0GC / SA-AK63 0GN

Step 6 Press the POWER button to turn the power off.

[Opening the disc tray manually (Using service tools)]

Step 1 Insert the gear tool into the hole on the underside of CD

chassis and then rotate in the direction of arrow. The disc tray

will be opened.

Step 2 Release the 2 claws, and then remove the CD lid cover.

Step 3 Repeat Step 2 but rotate the gear tools in anti- clockwise

direction.

Step 4 The disc tray will be closed.

SA-AK63 0GC / SA-AK63 0GN

Step 1 Remove 7 screws and disconnect wire CN2810 (Fan) at

rear cabinet as shown.

Step 1 Remove one screw at rear panel.

Step 2 Detach the FFC wires (CN2801 & CN2805).

Step 3 Release the claws of both ends, and then lift up the CD

Mechanism Unit.

Step 4 Remove 4 screws.

Step 5 Remove the CD chassis.

Step 6 Lay the CD mechanism unit as shown.

For disassembly of CD mechanism unit, please refer to

Section 9.13 of this manual.

9.5. Disassembly of Rear Panel

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

9.6. Disassembly of CD Mechanism Unit

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

SA-AK63 0GC / SA-AK63 0GN

Step 1 Disconnect FFC wires CN2803 & CN2806 from Main

P.C.B.

Step 1 Remove the 2 screws fixed at Sub Power P.C.B..

Step 2 Lift up Main P.C.B. by disconnecting connectors

CN5800 & CN5801 as arrow shown above.

Step 2 Remove 2 screws at Power Amplifier IC.

Step 3 Disconnect connector CN5803

Step 4 Lift up the Sub Power P.C.B. to remove it.

9.7. Disassembly of Main P.C.B.

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

9.8. Disassembly of Sub-Power P.C.B.

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B.

SA-AK63 0GC / SA-AK63 0GN

Replacement of Power Amplifier IC

Step 1 Desolder the terminals of Power Amplifier IC and

replace the component.

Step 1 Remove the 2 screws fixed at heat sink.

Step 2 Remove 1 screw fixed at Power P.C.B..

Note:

Insulate the Power P.C.B. with insulation material to avoid short

circuit.

9.9. Disassembly of Power P.C.B.

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

Follow the (Step 1) - (Step 2) of Item 9.7 - Disassembly of Main P.C.B.

SA-AK63 0GC / SA-AK63 0GN

Step 1 Remove 2 screws fixed to the Power Amplifier IC and 1

screw to Voltage Regulator.

Step 2 Break the joint with a metal cutter as shown below.

Step 1 Remove 3 screws, disconnect connector CN5950.

Step 3 Unsolder the terminals of Power Amp IC, transistor and

replace the components.

Step 4 Fix back the cut portion with a screw as shown.

Replacement of the Power Amplifier IC/ Voltage Regulator

9.10. Disassembly of Transformer P.C.B.

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) of Item 9.5 - Disassembly of Rear Panel

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

SA-AK63 0GC / SA-AK63 0GN

Step 1 Lay the unit as shown below.

Step 2 Release 2 claws at bottom and 2 claws each side, draw

the front panel ass’y forward.

Step 3 Remove volume knob and adaptor.

Disassembly of Panel P.C.B.

Step 4 Remove 10 screws.

Step 5 Disconnect connectors (CN2806, CN2803 and

CN5950).

9.11. Disassembly of Front Panel Unit

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

9.12. Disassembly of Deck Mechanism Unit

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) - (Step 3) of Item 9.6 - Disassembly of CD Mechanism Unit

SA-AK63 0GC / SA-AK63 0GN

Step 1 Detach FFC wire (CN971).

Step 2 Disconnect FFC flat cable from the connector

(CN1001).

Step 3 Remove the 5 screws.

Step 1 Remove the CD changer unit.

Step 4 Push the lever upward, and then open the cassette lid

ass’y (For DECK1 and DECK2).

Step 5 Tilt the cassette mechanism unit in the direction of

arrow (1), and then remove it in the direction of arrow (2).

For replacement of Deck Mechanism P.C.B.

Step 6 Remove 3 screws.

Step 7 Unsolder the motor terminals.

Step 8 Remove Deck Mechanism P.C.B.

Step 2 Insert the gear with hexagonal wrench into the hole.

Step 3 Rotate the hexagonal wrench in the direction of arrow

(clockwise), and then open the disc tray fully.

Follow the (Step 1) - (Step 3) of Item 9.11 - Disassembly of Front Panel Unit

9.13. CD Mechanism Main Component Replacement Procedures

Follow the (Step 1) - (Step 2) of Item 9.3 - Disassembly of Top Cabinet

Follow the (Step 1) - (Step 6) of Item 9.4 - Disassembly of CD Lid

Follow the (Step 1) - (Step 6) of Item 9.6 - Disassembly of CD Mechanism Unit

9.13.1. Replaceme nt of the Traverse Deck

SA-AK63 0GC / SA-AK63 0GN

Step 4 With pressing the claw (A), rotate the hexagonal wrench

clockwise. (The slide plate R moves for a little amount.)

Step 5 Pressing the claw (B) in the direction of arrow (1), the

connection lever moves in the direction of arrow (2).

Step 6 Lift up the traverse deck ass’y.

Step 7 Remove the traverse deck ass’y from the timing lever.

Caution:

When removing or inserting the traverse deck avoid touching

the OPU lens and pressing onto the turntable.

Step 8 Remove 3 screws.

Step 9 Unsolder the motor terminals (4 points).

Step 10 Remove the FFC board from the connector, and then

remove the CD Servo P.C.B.

SA-AK63 0GC / SA-AK63 0GN

Step 11 Remove the pin.

Step 12 Release the claw, and then remove the traverse deck

ass’y.

Note:

Be careful not to lose the 3 floating spring because those will

also be removed on removal of the traverse deck ass’y.

Installation of the CD Servo P.C.B. after replacement

Step 1 Connect the FFC board.

Step 2 Install the CD servo P.C.B. in the traverse deck ass’y.

Step 3 Remove 3 screws.

Step 4 Solder.

Note for installation of the CD servo P.C.B.

Installation for traverse deck ass’y

Step 1 Install the traverse deck ass’y to the timing lever.

Step 2 Align the boss of traverse deck ass’y with the slot of

traverse cam gear.

SA-AK63 0GC / SA-AK63 0GN

Step 3 Force the claw of timing lever.

Step 1 Remove 4 screws.

Step 2 Remove the upper plate.

Step 3 Remove 3 screws.

Step 4 With lifting the claw in the direction of (1), draw the CD

Detect P.C.B. in the direction of arrow (2).

Step 4 Force the disc tray fully.

Step 5 With pressing the claw (B) in the direction of arrow (1),

force the connection lever in the direction of arrow (2).

Step 5 Remove the mechanism cover.

9.13.2. Replaceme nt for the Disc Tray

SA-AK63 0GC / SA-AK63 0GN

Step 6 Insert the gear with hexagonal wrench into the hole.

Step 7 Rotate the hexagonal wrench in the direction of arrow,

and then open the disc tray fully.

Step 8 Release the both claws, and then draw the disc tray.

Step 9 With forcing the left guide bar manually because the left

guide bar interfers with claw, draw the disc tray.

[Installation of the disc tray after replacement]

Step 1 Slide the drive rack fully in the direction of arrow.

Step 2 Holding the drive rack not to move, install the disc tray.

Step 3 Align the drive rack with the drive gear.

SA-AK63 0GC / SA-AK63 0GN

Step 1 Remove 3 screws.

Step 2 Release the claw, and then remove the gear holder.

Step 3 Remove the belt and change gear spring.

NOTE:

Take care not to lose the change gear spring.

Step 4 Remove the pulley gear, change gear and UP/DOWN

gear.

NOTE:

Force the right guide bar of tray base manually not to move

upwards.

Step 4 Holding the disc tray manually, push the disc tray in the

direction of the arrow.

Step 5 Release the 2 claws, and then remove the bottom SW

P.C.B..

9.13.3. Disassemb ly and reassembly for mechanism base drive unit

SA-AK63 0GC / SA-AK63 0GN

Step 6 Install the tray lock spring to hook temporary.

Step 7 Release the claw, and then remove the tray lock.

Step 8 Release the claw, and then remove the rear lock.

Step 9 Pressing the claw (B) in the direction of arrow (1), force

the connection lever in the direction of arrow (2).

Step 10 Move the slide plate 1 to the end of stock side.

SA-AK63 0GC / SA-AK63 0GN

Step 11 Lift up the left end of spindle base unit in the direction

of arrow (1), and then remove the unit in the direction of arrow

(2).

Step 12 Remove slide plate 1 and slide plate 2.

Step 13 Remove the traverse relay gear, traverse cam gear

and drive gear.

[Dissassembly/reassembly for the spindle base unit]

Step 1 Draw the 5 disc spacers.

Step 2 Pushing the claw, slide the support plate in the direction

of arrow, and then remove it.

SA-AK63 0GC / SA-AK63 0GN

Step 3 Rotate the disc lever in the direction of arrow (1), draw

the disc lever.

NOTE:

Take care not to lose the disc lever spring.

Step 4 Release the 2 claws, and then draw the relay gear B.

Step 5 Release the 2 claws as shown below.

NOTE:

Hold the loading stopper ass’y manually bacause it is flipped by

spring.

Step 6 Remove the cushion spring.

Step 7 Remove the loading stopper ass’y in the direction of

arrow.

SA-AK63 0GC / SA-AK63 0GN

Step 8 Release the 2 claws, and then remove the relay gear A.

Step 9 Release the 2 claws, and then remove the spindle shaft.

Step 10 Remove the lower spindle spring with tweezers.

Step 11 Force the lower hook with thin tip of minus screwdriver.

Step 12 Squeeze the shaft of lower hook, and then draw it.

Step 13 Rotate the lower spindle in the direction of arrow until

the lower spindle interferes with stopper.

Step 14 Insert the thin tip of minus screwdriver between the

lower spindle and UP/DOWN base, and then slacken the lower

spindle to release the stopper. Then, rotate the lower spindle

and remove it.

Step 15 Rotate the UP/DOWN base at a 90° angle. Then,

SA-AK63 0GC / SA-AK63 0GN

spread the hold bars of loading stopper and remove the

UP/DOWN base.

[Installation for loading stopper ass’y]

Step 1 Align the claw of loading stoppers ass’y with the slot of

spindle base. (Caution should be exercised when alignment of

claw due to the size of claws.)

Step 2 Lower the loading stopper ass’y, and then align the

lower spindle with the trapezoid tooth of relay gear A.

Step 3 Force the loading stopper ass’y, latch the claw firmly.

[Reassembly for mechanism base drive unit]

Step 1 Install the traverse cam gear.

Step 2 Rotate the traverse cam gear to the direction of arrow.

Step 3 Install the drive gear and traverse relay gear.

*When installing the traverse relay gear, align the trapezoid

tooth of gear with tooth of traverse cam gear.

SA-AK63 0GC / SA-AK63 0GN

+ 82 hidden pages