Ryobi Outdoor RY52002 User Manual

OPERATOR’S MANUAL

PC30 PRUNER/TRIMMER

RY52002

Your pruner/trimmer has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for buying a Ryobi product.

SAVE THIS MANUAL FOR FUTURE REFERENCE

TABLE OF CONTENTS

n Introduction ..................................................................................................................................................................... 2

�n General Safety Rules ....................................................................................................................................................... 3

�n Specific Safety Rules....................................................................................................................................................... 4

�n Symbols........................................................................................................................................................................ 5-6

��n Features........................................................................................................................................................................7-8

��n Assembly .................................................................................................................................................................... 8-10

�n Operation..................................................................................................................................................................11-14

n Maintenance ............................................................................................................................................................. 15-21

n Troubleshooting............................................................................................................................................................. 22

n Warranty ................................................................................................................................................................... 23-25

��n Parts Ordering / Service ................................................................................................................................................ 26

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product, making it easy to maintain and operate.

2 3

GENERAL SAFETY RULES

WARNING!

Read and understand all instructions. Failure to follow

all instructions listed below, may result in electric shock,
fire and/or serious personal injury.

READ ALL INSTRUCTIONS

n For safe operation, read and understand all instruc-

tions before using this product. Follow all safety instruc-

tions. Failure to follow all safety instructions listed below,
can result in serious personal injury.

�n Do not allow children or untrained individuals to use this

unit.

n Never let anyone use the machine who has not received

adequate instructions in the machine’s proper use. This
applies to rentals as well as privately owned units and
also to the power head it is attached to.

n Always wear sa fety gl asses with side shields.

Everyday glasses have only impact resistant lenses. They
are NOT safety glasses. Following this rule will reduce the
risk of eye injury.

n Product users on United States Forest Service land, and

in some states, must comply with fire prevention regula­tions. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
your federal, state, or local authorities.

n Wear heavy, long pants, boots, and gloves. Do not wear

loose fitting clothing, short pants, or go barefoot. Do not
wear jewelry of any kind.

n Never operate this unit on the operator’s left side.

n Secure long hair above shoulder level to prevent entangle-

ment in moving parts.

n Keep all bystanders, children, and pets at least 50 ft.

away.

n Do not operate this unit when you are tired, ill, or under

the influence of alcohol, drugs, or medication.

n Do not operate in poor lighting.

n Do not operate in rain or use in damp or wet environ-

ments.

n Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot
surfaces.

n Keep all parts of your body away from any moving part.

n To avoid hot surfaces, never operate the unit with the

bottom of the engine above waist level.

n Do not touch area around the muffler or cylinder of the

unit. These parts get hot from operation.

�n Always stop the engine and remove the spark plug wire

before making any adjustments or repairs except for
carburetor adjustments.

�n Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace any damaged parts before use.

�n The chain may rotate during carburetor adjustments.

�n It has been reported that vibrations from hand-held tools

may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. It is presently unknown what, if any, vibrations
or extent of exposure may contribute to the condition.
There are measures that can be taken by the operator to
possibly reduce the effects of vibration:

a) Keep your body warm in cold weather. When operat-

ing the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.

b) After each period of operation, exercise to increase

blood circulation.

c) Take frequent work breaks. Limit the amount of ex-

posure per day.

d) Keep the tool well maintained, fasteners tightened and

worn parts replaced.

If you experience any of the symptoms of this condition,

immediately discontinue use and see your physician
about these symptoms.

n Mix and store fuel in a container approved for gasoline.

n Mix fuel outdoors where there are no sparks or flames.

Wipe up any fuel spillage. Move 30 ft. away from refueling
site before starting engine.

n Stop the engine and allow to cool before refueling or

storing the unit.

n Allow the engine to cool, empty the fuel tank, and secure

the unit from moving before transporting in a vehicle.

n Check for damaged parts. Before further use of the tool,

any part that is damaged should be carefully checked
to determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly
repaired or replaced by an authorized service dealer.
Following this rule will reduce the risk of shock, fire, or
serious injury.

SPECIFIC SAFETY RULES

SPECIFIC SAFETY RULES FOR PRUNER USE

n Kickback is a dangerous reaction that can lead to serious

injury. Kickback may occur when the moving chain con­tacts an object at the upper portion of the tip of the guide
bar or when the wood closes in and pinches the chain
in the cut. Contact at the upper portion of the tip of the
guide bar can cause the chain to dig into the object and
stop the chain for an instant. The result is a lightning-fast,
reverse reaction which kicks the guide bar up and back
toward the operator. If the chain is pinched along the top
of the guide bar, the guide bar can be driven rapidly back
toward the operator, which can cause loss of control and
may result in serious injury. Do not rely exclusively upon
the safety devices built into the product.

With a basic understanding of kickback, you can reduce

or eliminate the element of surprise. Sudden surprise
contributes to accidents.

n Make sure that the area in which you are cutting is free

from obstructions. Do not let the nose of the guide bar
contact a log, branch, fence, or any other obstruction
while you are operating the unit.

n Cut only when visibility and light are adequate for you to

see clearly.

n Do not use on a ladder or unstable support. Always cut

with both feet on solid ground to prevent being pulled off
balance.

n To protect yourself from electrocution, do not operate

within 50 feet of overhead electrical lines.

n Before starting the engine, make sure the chain is not

contacting any object.

n Always cut with the engine running at full speed. Fully

squeeze the throttle trigger and maintain a steady cutting
speed.

n Do not force tool. Use the correct tool for your applica-

tion. The correct tool will do the job better and safer at
the rate for which it is designed.

n To protect yourself from falling branches, do not stand di-

rectly under the branch or limb being cut. This unit should
not be held at an angle over 60° from ground level.

n Keep the handles dry, clean, and free of oil or fuel mix-

ture.

n Shut off the engine and make sure the cutting attachment

has stopped before setting the unit down.

n To prevent electrical shock or serious personal injury, do

not use this product with any AC power head.

n Follow the sharpening and maintenance instructions for

the saw chain.

n Use only the replacement guide bars and low kickback

chains specified for the unit.

SPECIFIC SAFETY RULES FOR TRIMMER
USE

n Replace string head if cracked, chipped, or damaged

in any way. Be sure the string head or blade is properly
installed and securely fastened. Failure to do so can cause
serious injury.

n Make sure all guards, straps, deflectors, and handles are

properly and securely attached.

n Use only the manufacturer’s replacement string in the

cutting head. Do not use any other cutting attachment.
To install any other brand of cutting head to this string
trimmer can result in serious personal injury.

n Never operate unit without the grass deflector in place

and in good condition.

n Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string
head located over 30 in. or more above the ground.

REFUELING

n FUEL IS HIGHLY FLAMMABLE. Take precautions when

using to reduce the chance of serious personal injury.

n Store fuel in a cool, well-ventilated area, safely away from

spark and/or flame-producing equipment

n Store fuel in containers specifically designed for this

purpose.

n Only refuel outdoors and do not smoke while refueling.

n Add fuel before starting the engine. Never remove the cap

of the fuel tank or add fuel while the engine is running or
when the engine is hot.

n If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.

n Replace all fuel tank and container caps securely.

n If the fuel tank has to be drained, do this outdoors.

4 5

SYMBOLS

50' 15m

50'

15m

50' 15m

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Precautions that involve your safety.

Read The Operator’s Manual To reduce the risk of injury, user must read and

understand operator’s manual before using this
product.

Eye, Hearing, and Head Protection Wear eye, hearing, and head protection when

operating this equipment.

Safety Footwear Wear non-slip safety footwear when using this

equipment.

Gloves Wear non-slip, heavy-duty protective gloves

when handling the pole pruner attachment and
the saw chain.

Moving Parts Keep hands away from moving parts.

Keep Bystanders Away Keep all bystanders at least 50 ft. (15 m) away.

Kickback DANGER! Beware of kickback.

Hot Surfaces Indicates HOT SURFACES. Keep all body parts

away from all hot surfaces.

Risk of Electrocution DANGER! Risk of electrocution!

Use unleaded gasoline intended for motor vehicle

Gasoline and Oil

use with an octane rating of 87 [(R + M)/2] or higher.
This product is powered by a 2-cycle engine and
requires pre-mixing gasoline and 2-cycle oil.

Ricochet

Thrown objects can ricochet and result in personal
injury or property damage.

No Blade

Do not install or use any type of blade on a product
displaying this symbol.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury.

CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in

property damage.

SERVICE

Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic­ing, use only identical replacement parts.

WARNING:

To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera­tion and instructing others who may use this product.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles,
safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.

SAVE THESE INSTRUCTIONS

6 7

FEATURES

PRODUCT SPECIFICATIONS

Engine displacement....................................................................................................................................................... 30cc

Bar length ....................................................................................................................................................................... 10 in.

String cutting width ........................................................................................................................................................ 17 in.

String diameter........................................................................................................................................................... .080 in.

STARTER GRIP

CHAIN OILER

TANK CAP

ENGINE

SWITCH

“J” BARRIER

HANDLE

PRIMER BULB

SCABBARD

BAR

CHAIN

PRUNER

ATTACHMENT

COUPLER

THROTTLE

TRIGGER

SHOULDER

STRAP

KNOB

TRIMMER

ATTACHMENT

Fig. 1

FEATURES

KNOW YOUR PRUNER/TRIMMER

See Figure 1.

Before attempting to use this product, familiarize yourself
with all operating features and safety rules.

ENGINE SWITCH

The engine switch controls the ignition system. The switch
must be in the ON (I) position for the engine to start and
run.

“J” BARRIER HANDLE

Using the J” Barrier handle allows better control of the pruner
to maximize operator safety.

PRIMER BULB

The priming bulb pumps fuel from the fuel tank to the car­buretor. This is necessary only when starting a cold engine
or after refueling an engine that has run out of fuel.

ASSEMBLY

UNPACKING

This product requires assembly.

n Carefully remove the tool and any accessories from the

box. Make sure that all items listed in the packing list are
included.

n Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

n Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

n If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

WARNING:

If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to heed this warning
could result in possible serious personal injury.

WARNING:

Do not attempt to modify this tool or create accesso­ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.

SHOULDER STRAP

The shoulder strap helps support the weight of the pruner
during use.

START LEVER

The start lever opens and closes the choke valve in the
carburetor.

STARTER GRIP

The starter grip is used for starting the engine.

THROTTLE TRIGGER

The throttle trigger is used for starting the pruner, and also
for controlling blade rotation.

PACKING LIST

Power Head Assembly
Pruner Attachment
Trimmer Attachment
Hex Screw
Flat Washer
Wing Nut
Lock Washer
Curved Shaft Grass Deflector
Scabbard
Scrench (5/8 in. x 3/4 in.)
8 oz. Bar and Chain Oil
Bottle of 2-cycle oil
Shoulder Strap Bracket
Bolt
Nut
Shoulder Strap
“J” Barrier Handle Assembly:
“J” Barrier Handle
Top and Bottom Clamp
Short Bolt
Long Bolt
Flat Washers (2)
Lock Washers (2)
Nuts (2)
Operator’s Manual
Warranty Registration Card

8 9

ASSEMBLY

WARNING:

To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.

ATTACHING THE “J” BARRIER HANDLE

See Figure 2.

n Hold the top and bottom clamp snugly in position on the shaft

housing so that the handle will be located to the operator’s
left.

n Insert the end of the handle between the clamps.

Align the bolt holes and push the long bolt (1/4-20 x

n

1-1/2 in.) through the handle side.

Place short bolt (1/4-20 x 1 in.) through opposite side of the

n

clamp. Install the flat washer, lock washers, and hex nuts to
hold the assembly in place.

After assembly is complete, adjust the position of the handle

n

for best balance and comfort.

n Tighten the long bolt first and then the short bolt.

NOTE:

the coupler for pruning, and closer to the powerhead for trim
ming. Refer to the label located on the shaft housing for the
correct location to install the handle.

The “J” barrier handle should be positioned closer to

n Pull apart the ends of the bracket to expand slightly.

Slide the bracket over the power head shaft immediately

n

behind the “J” Barrier Handle.

Squeeze bracket ends together to retighten.

n

n Reinstall the bolt, lock washer, and hex nut to secure.

Connect the latch on the shoulder harness to the strap

n

hanger.

NOTE:

strap bracket when pruning, and the strap hanger located just
above the engine switch when trimming.

-

For proper balance, use the strap hanger on the shoulder

SHOULDER

“J” BARRIER

HANDLE

STRAP

LATCH

BOLT

PRUNING

STRAP

HANGER

PRUNING

HANDLE POSITION

LONG BOLT

SHORT BOLT

TRIMMING

HANDLE POSITION

HEX NUT

CLAMP

CLAMP

FLAT WASHER

LOCK WASHER

“J” BARRIER

HANDLE

Fig. 2

INSTALLING THE SHOULDER STRAP

See Figure 3.

The shoulder strap provides added support of the pruner
during operation.

To install the shoulder strap bracket:

n Remove the hex nut, lock washer, and bolt from the

shoulder strap bracket.

LOCK NUT

NUT

BOLT

NUT

FIG. A

BOLT

LOCK

WASHER

FIG. B

Fig. 3

CONNECTING THE POWER HEAD TO THE
PRUNER ATTACHMENT

See Figure 4.

The pruner attachment connects to the power head by means
of a coupler device.

To install the attachment:

n Loosen the knob on the coupler of the power head shaft

and remove the end cap from the attachment.

n Push in the button located on the shaft of the pruner at

tachment. Align the button with the guide recess on the
power head coupler and slide the two shafts together.
Rotate extension shaft until button locks into the posi
tioning hole.

NOTE:

blade in a vertical position. If the button does not release
completely in the positioning hole, the shaft is not locked
into place. Slightly rotate from side to side until the button
is locked into place.

n Tighten the knob securely.

The attachment should only be operated with the

-

-

ASSEMBLY

To remove:

n Loosen the knob.

n Push in the button and twist the shafts to remove and

separate ends.

POWER HEAD

SHAFT

GUIDE

RECESS

BUTTON

PRUNER

ATTACHMENT

COUPLER

POSITIONING

HOLE

KNOB

Fig. 4

CHAIN OILER

Add bar and chain oil in the chain oiler tank before starting
the engine of the power head.

FUELING AND REFUELING

FUEL MIXTURE

This product is powered by a 2-cycle engine and requires pre­mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline
and 2-cycle engine oil in a clean 1 gallon container approved
for gasoline.

n This engine is certified to operate on unleaded gasoline

intended for automotive use.

n Mix high quality 2-cycle engine oil at 2.6 oz. per gallon.

n Do not use automotive oil or 2-cycle outboard oil.

n DO NOT mix quantities larger than usable in a 30-day

period.

n Carefully pour fuel into the tank. Avoid spillage.

n Prior to replacing the fuel cap, clean and inspect the

gasket.

n Immediately replace fuel cap and hand tighten. Wipe up

any fuel spillage.

NOTE: It is normal for smoke to be emitted from a new
engine after first use.

WARNING:

Always shut off engine before fueling. Never add fuel to
a machine with a running or hot engine. Move at least
30 ft. from refueling site before starting the engine. Do
not smoke!

INSTALLING THE GRASS DEFLECTOR
ON THE STRING TRIMMER ATTACHMENT

See Figure 5.

WARNING:

The line cutting blade on the grass deflector is sharp.
Avoid contact with the blade. Failure to avoid contact
can result in serious personal injury.

n Press the grass deflector onto the bottom of the curved

shaft as shown.

n Insert the hex screw through the grass deflector and the

bracket on the curved shaft.

n Place the flat washer and lock washer on the hex head

cap screw.

n Place the wing nut on the hex head cap screw and tighten

securely.

HEX

SCREW

BRACKET

GRASS

DEFLECTOR

PREMIUM EXACT MIX™ (50:1)

GASOLINE OIL

1 Gallon (US) 2.6 oz.

1 Liter 20 cc (20 ml)

FILLING TANK

n Clean surface around fuel cap to prevent contami-

nation.

n Loosen fuel cap slowly. Rest the cap on a clean

surface.

LOCK

WASHER

FLAT

WASHER

10 11

WING NUT

Fig. 5

OPERATION

WARNING:

Do not allow familiarity with tools to make you care­less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with
side shields, a hard hat, and safety shoes when
operating tools. Failure to do so could result in
objects being thrown into your eyes, resulting in
possible serious injury.

WARNING:

Do not use any attachments or accessories not rec­ommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.

n Make a shallow first cut (1/4 of limb diameter) on the

underside of the limb close to the main limb or trunk.

n Make a second cut from the top side of the limb outboard

from the first cut.

n Make a final cut close to trunk.

�NOTE: For second and final cuts (from top of limb or branch),
hold front cutting guide against the limb being cut. This will
help steady the limb and make it easier to cut. Allow chain to
cut for you; exert only light downward pressure. If you force
the cut, damage to the bar, chain, or engine can result.

LOAD

FIRST CUT

1/4 DIAMETER

FINAL CUT

SECOND CUT

WARNING:

To avoid kickback, binding of the saw bar, and possible
injury, never cut limbs that the pruner does not reach
when supported by the shoulder strap.

PREPARATION FOR PRUNER CUTTING

See Figures 6 - 7.

n Wear non-slip gloves for maximum grip and protection.

�n Maintain a proper grip on the unit whenever the engine is

running. Use your right hand to firmly grip the rear handle
while your left hand has a firm grip on the front handle.

�n Hold unit firmly with both hands. Always keep your left

hand on the front handle and your right hand on the rear
handle, so your body is to the left of the chain line. Never
use a left-handed (cross-handed) grip, or any stance that
places your body or arm across the chain line.

�n Never stand directly under the limb you are cutting.

�n Always wear shoulder strap for increased safety and to

support the pruner.

n Be certain the knob is fully tightened before operating

equipment; check it periodically for tightness during use
to avoid serious injury.

BASIC CUTTING PROCEDURE

Follow the steps below to prevent damage to tree or shrub
bark. Do not use a back-and-forth sawing motion.

n Accelerate the engine to full throttle just before entering

the cut by squeezing the throttle trigger. Keep the engine
at full throttle the entire time you are cutting.

Fig. 6

n Release the trigger as soon as the cut is completed, allow

ing the engine to idle. If you run the pruner at full throttle
without a cutting load, unnecessary wear or damage can
occur to the chain, bar, and engine.

CUTTING GUIDE

Failure to follow proper cutting procedures will result in the
bar and chain binding and becoming pinched or trapped in
the limb. If this should happen:

n Stop the engine.

n Loosen the knob on the coupler.

n Depress the button on the shaft; twist and pull the shafts

to separate the pruner from the power head.

n If the limb can be reached from the ground, lift the limb

while holding the attachment. This should release the
“pinch” and free the pruner.

n If the pruner is still trapped, call a professional for as

sistance.

Fig. 7

-

-

OPERATION

LIMBING AND PRUNING

See Figures 8 - 9.

This unit is designed for trimming small branches and limbs
up to 6 in. in diameter. For best results, observe the follow­ing precautions.

n Plan the cut carefully. Be aware of the direction in which

the branch will fall.

n Branches may fall in unexpected directions. Do not stand

directly under the branch being cut.

n The most typical cutting application is to position the unit

at an angle of 60° or less, depending on the specific situ­ation, as shown below. As the angle of the pruner shaft
to ground increases, the difficulty of making the first cut
(from the underside of limb) increases.

�n Remove long branches in several stages.

�n Cut lower branches first to allow the top branches more

room to fall.

Fig. 9

OPERATING THE TRIMMER

See Figure 10.

WARNING:

Always position the unit on the operator’s right side. The
use of the unit on the operator’s left side will expose
the user to hot surfaces and can result in possible burn
injury.

60° MAXIMUM

Fig. 8

n Work slowly, keeping both hands on the saw with a firm

grip. Maintain secure footing and balance.

n Keep the tree between you and the chain while limbing.

Cut from side of tree opposite branch you are cutting.

�n Do not cut from a ladder; this is extremely dangerous.

Leave this operation for professionals.

�n Do not to make the flush cut next to the main limb or trunk

until you have cut off the limb further out to reduce the
weight. Following proper cutting procedures will prevent
stripping the bark from the main member.

�n Do not use the pruner for felling or bucking.

�n To prevent electrocution, do not operate within 50 ft. of

overhead electrical lines.

�n Keep bystanders at least 50 ft. away.

WARNING:

To avoid burns from hot surfaces, never operate unit with
the bottom of the engine above waist level.

Hold the trimmer with your right hand on the rear handle
and your left hand on the front handle. Keep a firm grip with
both hands while in operation. Trimmer should be held at a
comfortable position with the rear handle about hip height.

PROPER

OPERATING POSITION

Fig. 10

12 13

OPERATION

Always operate trimmer at full throttle. Cut tall grass from
the top down. This will prevent grass from wrapping around
the shaft housing and string head which could cause
damage from overheating. If grass becomes wrapped around
the string head, STOP THE ENGINE, disconnect the spark
plug wire, and remove the grass. Prolonged cutting at partial
throttle will result in oil dripping from the muffler.

WARNING:

Always hold the string trimmer away from the body keep­ing clearance between the body and the product. Any
contact with the housing or string trimmer cutting head can
result in burns and/or other serious personal injury.

TO ADVANCE THE CUTTING LINE

String advance is controlled by tapping the string head on
grass while running engine at full throttle.

n Run engine at full throttle.

n Tap the spool retainer on ground to advance string. The

string advances each time the spool retainer is tapped.
Do not hold the spool retainer on the ground.

NOTE: The line trimming cut-off blade on the grass deflector
will cut the line to the correct length.

NOTE: If the string is worn too short you may not be able to
advance the string by tapping it on the ground. If so, stop
the engine, and manually advance the string.

TO ADVANCE THE CUTTING LINE MANUALLY

Push the spool retainer down while pulling on string(s) to
manually advance the string.

GRASS DEFLECTOR LINE TRIMMING CUT-OFF
BLADE

See Figure 12.

The trimmer is equipped with a line trimming cut-off blade
on the grass deflector. For best cutting, advance string until
it is trimmed to length by the cut-off blade. Advance the
string whenever you hear the engine running faster than
normal, or when trimming efficiency diminishes. This will
maintain best performance and keep the string long enough
to advance properly.

DANGEROUS

CUTTING AREA

BEST CUTTING

AREA

DIRECTION OF

ROTATIOPN

Fig. 11

CUTTING TIPS

See Figure 11.

n Avoid hot surfaces by always keeping the tool away from

your body. (Proper operating position shown in figure 10.)

n Keep the trimmer tilted toward the area being cut; this is

the best cutting area.

n The curved shaft trimmer cuts when passing the unit

from right to left. This will avoid throwing debris at the
operator. Avoid cutting in the dangerous area shown in
illustration.

n Use the tip of string to do the cutting; do not force string

head into uncut grass.

n Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs, and wood may
wear string rapidly.

n Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by the string.

CURVED SHAFT TRIMMER

LINE TRIMMING CUT-OFF BLADE

Fig. 12

OPERATION

POSITION FOR STARTING

See Figure 13.

Lay the pruner on the ground and ensure that no objects or
obstructions are in the immediate vicinity. Make sure nothing
can come in contact with the bar and chain.

Fig. 13

STARTING AND STOPPING

See Figures 14 - 16.

TO START A COLD ENGINE:

DO NOT squeeze the throttle trigger until the engine starts
and runs.

�n Lay the trimmer on a flat, bare surface.

�n PRIME - Press the primer bulb 7 times.

�n SET the start lever to the START position.

�n PULL the rope until the engine starts.

�n Allow the engine to run for 15 seconds.

�n Squeeze trigger lock and throttle trigger.

NOTE: Squeezing the throttle trigger releases the start lever
to the RUN position.

STARTER

GRIP

ENGINE

SWITCH

PRIMER BULB

TRIGGER

LOCK

THROTTLE TRIGGER

Fig. 15

START LEVER

START

POSITION

TO START A WARM ENGINE:

PULL the rope until the engine starts.

TO STOP THE ENGINE:

Press and hold the switch in the stop “ ” position until the
engine stops.

ENGINE

SWITCH

TRIGGER

LOCK

THROTTLE

TRIGGER

Fig. 14

START LEVER

RUN

POSITION

Fig. 16

14 15

MAINTENANCE

WARNING:

When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.

WARNING:

Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.

WARNING:

Before inspecting, cleaning or servicing the unit (except
for carburetor adjustments), shut off engine, wait for all
moving parts to stop, and disconnect spark plug wire
and move it away from spark plug. Failure to follow
these instructions can result in serious personal injury
or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.

n Stop the engine before setting the chain tension. Make

sure the guide bar nut is loose to finger tight, turn the
chain tensioning screw clockwise to tension the chain.
Refer to “Replacing the Bar and Chain” for additional
information.

NOTE: A cold chain is correctly tensioned when there is

no slack on the underside of the guide bar, the chain is
snug, but it can be turned by hand without binding.

n Chain must be re-tensioned whenever the flats on the

drive links hang out of the bar groove as shown in fig.

17.

n During normal operation, the temperature of the chain will

increase. The drive links of a correctly tensioned warm
chain will hang approximately .050 in. (1.25 mm) out of
the bar groove, as shown in fig. 18.

NOTE: New chain tends to stretch; check chain tension
frequently and tension as required.

CAUTION:

Chain tensioned while warm, may be too tight upon cool­ing. Check the “cold tension” before next use.

FLATS

WARNING:

Do not at any time let brake fluids, gasoline, petroleum­based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic, which may result in serious personal injury.

Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Ryobi Authorized Service Center.

CHAIN TENSION

See Figures 17 - 18.

WARNING:

To avoid possible serious injury, never touch or adjust the
chain while the motor is running. The saw chain is very
sharp; always wear protective gloves when performing
maintenance to the chain.

APPROX .050 IN. (1.25 mm)

Fig. 17

Fig. 18

MAINTENANCE

REPLACING THE BAR

See Figures 19 - 24.

WARNING:

To avoid possible serious injury, stop engine before re­placing the bar, chain, or performing any maintenance
operation.

n Remove the bar nut and drivecase cover.
n The bar contains a bar stud slot that fits over the bar stud.

The bar also contains a chain tensioning pin hole which
fits over the chain tensioning pin.

n Place the bar onto the bar stud so that the chain tension-

ing pin fits into the chain tensioning pin hole.

n Fit the chain over the sprocket and into the bar groove.

The cutters on the top of the bar should face toward the
bar tip, in the direction of the chain rotation.

n Replace the side case cover and install the bar nut.

Tighten the bar nut finger tight only. The bar must be
free to move for tension adjustment.

CHAIN

BAR

BAR NUT

DRIVECASE

COVER

n Remove all slack from chain by turning the chain tension-

ing screw clockwise, assuring that the chain seats into
the bar groove during tensioning.

n Lift the tip of the bar up to check for sag. Release the tip

of the bar, and turn the chain tensioning screw 1/2 turn
clockwise. Repeat this process until sag does not exist.

n Hold the tip of the bar up and tighten the bar nut se-

curely.

n Chain is correctly tensioned when there is no slack on

the underside of the bar, the chain is snug, but it can be
turned by hand without binding.

NOTE: If chain is too tight, it will not rotate. Loosen the
bar nut slightly and turn adjusting screw 1/4 turn counter­clockwise. Lift the tip of the bar up and retighten bar nut.

CHAIN ROTATION

CHAIN

SPROCKET

CHAIN

TENSIONING PIN

BAR NUT

BAR STUD

BAR STUD SLOT

Fig. 19

DRIVECASE

COVER

Fig. 20

BAR

BAR NUT

Fig. 22

CHAIN

TENSIONING SCREW

Fig. 23

BAR NUT

SPROCKET

CHAIN TENSIONING

PIN HOLE

Fig. 21

Fig. 24

16 17

MAINTENANCE

IDLE SPEED ADJUSTMENT

See Figure 25.

If the chain turns at idle, the idle speed screw needs ad­justing on your trimmer engine. Turn the idle speed screw
counterclockwise to reduce the idle RPM and stop the chain
movement. If the saw chain still moves at idle speed, contact
a service dealer for adjustment and discontinue use until the
repair is made.

WARNING:

The saw chain should never turn at idle. Turn the idle
speed screw counterclockwise to reduce the idle RPM
and stop the chain, or contact a service dealer for ad­justment and discontinue use until the repair is made.
Serious personal injury may result from the saw chain
turning at idle.

IDLE

SPEED SCREW

CHAIN OILER

See Figure 26.

n Use Premium Bar and Chain Oil. It is designed for chains

and chain oilers and is formulated to perform over a wide
temperature range with no dilution required.

n Remove the cap and carefully pour approximately 8 oz.

of bar and chain oil into the chain oiler tank.

n Replace the cap and tighten securely.

n Check and refill the chain oiler tank every time the engine

is fueled.

NOTE: Do not use dirty, used or otherwise contaminated
oils. Damage may occur to the oil pump, bar, or chain.

CHAIN OILER TANK

REPLACE

CAP

Fig. 25

REMOVE

CAP

Fig. 26

MAINTENANCE

CHAIN MAINTENANCE

See Figure 27.

For smooth and fast cutting, the chain needs to be main­tained properly. The following conditions indicate that the
chain requires sharpening:

n Wood chips are small and powdery

n Chain must be forced through the wood during cutting

n Chain cuts to one side

During maintenance of the chain, consider the following:

n Improper filing angle of the side plate can increase the

risk of a severe kickback.

n Depth gauge (or raker clearance) setting determines the

height the cutter enters the wood and the size of the wood
chip that is removed. Too much clearance increases the
potential for kickback. Too little clearance decreases the
size of the wood chip thus decreasing the chain's cutting
ability.

n If cutter teeth have hit hard objects such as nails and

stones, or have been abraded by mud or sand on the
wood, have service dealer sharpen chain.

DEPTH GAUGE SETTING

n Use a 5/32 in. diameter round file and holder.

n Keep the file level with the top plate of the tooth. Do not

let the file dip or rock.

Fig. 29

n Using light but firm pressure, stroke towards the front

corner of the tooth. Lift file away from the steel on each
return stroke.

Fig. 27

HOW TO SHARPEN THE CUTTERS

See Figures 28 - 31.

Be careful to file all cutters to the specified angles and to
the same length, as fast cutting can be obtained only when
all cutters are uniform.

PARTS OF A CUTTER

TOP PLATE

RIVET HOLE

HEEL

n Tighten the chain tension enough that the chain does not

wobble. Do all of your filing at the mid-point of the bar.
Wear gloves for protection.

CUTTING CORNER

GULLET

SIDE PLATE

DEPTH GAUGE

TOE

Fig. 28

Fig. 30

n Put a few firm strokes on every tooth. File all left hand

cutters in one direction. Then move to the other side and
file the right hand cutters in the opposite direction. Oc­casionally remove filings from the file with a wire brush.

LEFT HAND

CUTTERS

RIGHT HAND

CUTTERS

Fig. 31

18 19

MAINTENANCE

CAUTION:

Dull or improperly sharpened chain can cause excessive
engine speed during cutting which may result in severe
engine damage.

WARNING:

Improper chain sharpening increases the potential of
kickback. Failure to replace or repair damaged chain
can cause serious injury.

SPOOL REPLACEMENT

NEW PREWOUND SPOOL

See Figures 32 - 33.

If replacing string only, refer to “String Replacement” later
in this manual.

Use only monofilament string. Use original manufacturer’s
replacement string for best performance.

n Stop the engine and disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

n Turn the spool retainer counterclockwise.

n Remove the empty spool from the string head. Keep the

spring attached to the spool.

n To install the new spool, make sure the two strings are

captured in the slots opposite each other on the new
spool. Make sure the ends of each string are extended
approximately 6 in. beyond each slot.

n Thread the strings into the eyelets in the string head.

Carefully push the spool into the string head (gently pull
the strings to the outside if necessary). When the spool
is positioned in the string head, grasp the strings and pull
sharply to release them from the slots in the spool.

n Push down and turn the spool counterclockwise until it no

longer turns. Hold the spool down and rotate clockwise
a small amount. Release the spool. The spool should be
locked down in the string head. If not, hold down and
rotate until locked.

n Make sure the string head and the spool retainer are

installed on the drive shaft.

SPOOL

RETAINER

Fig. 32

SPRING

SLOTS

EYELETS

STRING HEAD

SHAFT

Fig. 33

To install the spool retainer:

n Turn the spool retainer clockwise.

n Pull the strings again to rotate the spool into cutting

position. Push the spool retainer down while pulling on
string(s) to manually advance the string and to check for
proper assembly of the string head.

MAINTENANCE

STRING REPLACEMENT

See Figures 34 - 36.

Use only monofilament string. Use original manufacturer’s
replacement string for best performance.

n Stop the engine, disconnect the spark plug wire. Hold

the string head and unscrew the spool retainer.

To remove the spool retainer:

n Turn the spool retainer counterclockwise.

n Remove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove

any old string remaining on the spool.

n Cut two pieces of string, each being approximately 9 ft.

long.

n Insert the first string into the anchor hole in the upper part

of the spool. Wind the first string around the upper part of
the spool counterclockwise, as shown by the arrows on
the spool. Place string in the slot on upper spool flange,
leaving about 6 in. extended beyond the slot. Do not
overfill. After winding the string, there should be a
1/4 in. bet
of the spool.

n Repeat above step with second string, using the bottom

part of spool. Do not overfill.

n Replace the spool and the spool retainer. Refer to “Spool

Replacement” earlier in this manual.

ween the wound string and the outside edge

t least

SPRING

FIRST STRING

FIRST STRING

SLOT

SPOOL

ARROWS ON

SPOOL

ANCHOR

HOLE

Fig. 34

SECOND

STRING

SLOT

Fig. 35

ARROWS ON

SPOOL

Fig. 36

20 21

MAINTENANCE

CLEANING THE EXHAUST PORT AND
MUFFLER

Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port
and muffler may become blocked with carbon deposits. If
you notice a power loss with your gas powered tool, a quali­fied service technician will need to remove these deposits
to restore performance.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every 25 hours
or yearly to ensure proper performance of your product. For
the location of the spark arrestor and specific cleaning in­structions, contact your nearest authorized service center.

AIR FILTER COVER

KNOB

REPLACING AND CLEANING AIR FILTER

See Figures 37 - 38.

For proper performance and long life, keep air filter clean.

n Remove the air filter cover by pushing down on the latch

with your thumb while gently pulling on the cover.

n Remove the filter, clean it in warm soapy water. Rinse

and let dry completely. For best performance, replace
annually.

n Reinstall the filter.

n Replace the air filter cover by inserting the tabs on the

bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.

FUEL CAP

WARNING:

A leaking fuel cap is a fire hazard and must be replaced
immediately.

The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine perfor­mance. If performance improves when the fuel cap is loos­ened, check valve may be faulty or filter clogged. Replace
fuel cap if required.

AIR FILTER BASE

AIR FILTER COVER

Fig. 37

FILTER

Fig. 38

SPARK PLUG

This engine uses a Champion RCJ-6Y with .025 in. electrode
gap. Use an exact replacement and replace annually.

STORAGE (1 MONTH OR LONGER)

See Figure 39.

n Drain all fuel from tank into a container approved for

gasoline. Run engine until it stops.

n Clean all foreign material from the trimmer. Store it in a

well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals
and de-icing salts.

n Abide by all ISO and local regulations for the safe storage

Fig. 39

and handling of gasoline. Excess fuel should be used up
in other 2-cycle engine powered equipment.

�n Always place the sheath on the saw bar when transporting

or storing the pruner. The sheath is a snug fit and must
be attached very carefully due to the sharp teeth on the
saw chain. This is best done by grasping the sheath at
one end, in the center portion of the sheath, and carefully
sliding it over the chain as shown below. Use caution to
avoid the sharp teeth of the chain.

TROUBLESHOOTING

PROBLEM CAUSE REMEDY

Engine will not start. No spark.

No fuel.

Engine is flooded.

Starter rope pulls harder now
than when new.

Engine starts but will not
accelerate.

Engine starts but will only
run at high speed at half
choke.

Engine does not reach
fu l l sp e e d an d emit s
excessive smoke.

Engine requires approximately
three minutes to warm up.

Carburetor requires adjustment. Contact a servicing dealer.

Check oil fuel mixture.

Air filter is dirty.

Spark arrestor screen is dirty.

Check spark. Remove spark plug. Reattach the spark plug cap and lay
spark plug on metal cylinder. Pull the starter rope and watch for spark at
spark plug tip. If there is no spark, repeat test with a new spark plug.

Push primer bulb until bulb is full of fuel. If bulb does not fill, primary
fuel delivery system is blocked. Contact a servicing dealer. If primer
bulb fills, engine may be flooded, proceed to next item.

Pull starter three times with choke lever at “RUN”. If engine does not
start, move choke lever to “START” and repeat normal starting pro­cedure. If engine still fails to start, repeat procedure with a new spark
plug.

Contact a servicing dealer.

Allow engine to completely warm up. If engine does not accelerate
after three minutes, contact a servicing dealer.

Use fresh fuel and the correct 2-cycle oil mix.

Clean air filter. Refer to “Replacing and Cleaning Air Filter” earlier in
this manual.

Contact a servicing dealer.

Engine starts, runs, and
accelerates but will not
idle.

Bar and chain running
hot and smoking.

Motor runs, but chain is
not rotating.

String won’t advance String is welded to itself.

Spool retainer hard to
turn

Idle speed screw on carburetor Turn idle speed screw clockwise to increase idle speed.

Check chain tension for overtight
condition

Chain oil tank empty

Ch a i n t e n s i on t o o t i g h t.

Check guide bar and chain as­sembly.

Check guide bar and chain for
damage.

Not enough string on spool.

String is worn too short.

String is tangled on spool.

Engine speed is too slow.

Sc rew thre ads are di r ty or
damaged.

Tension chain. Refer to “Chain Tension” earlier in this manual.

Check oil tank.

Retension chain. Refer to “Chain Tension” earlier in this manual.

Refer to “Replacing the Bar and Chain” earlier in this manual.

Inspect guide bar and chain for damage.

Lubricate string with silicone spray.

Install more string. Refer to “String Replacement” earlier in this
manual.

Pull strings while alternately pressing down on and releasing spool
retainer.

Remove string from spool and rewind. Refer to “String Replacement”
earlier in this manual.

Advance string at full throttle.

Clean threads and lubricate with grease - if no improvement, replace
the spool retainer.

Gr a s s wr a p s aro und
driveshaft housing and
string head

Cutting tall grass at ground
level.

Op e r a ting tr i m m er at part
throttle.

Cut tall grass from the top down to prevent wrapping.

Operate trimmer at full throttle.

22 23

WARRANTY

LIMITED WARRANTY STATEMENT

Ryobi Technologies, Inc. warrants to the original retail
purchaser that this Ryobi Technologies, Inc. product is
free from defect in material and workmanship and agrees
to repair or replace, at Ryobi Technologies, Inc.’s discretion,
any defective product free of charge within these time
periods from the date of purchase.

�n Two years if the product is used for personal, family or

household use;

�n 90 days, if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.

Any part of the Ryobi Technologies, Inc. product
manufactured or supplied by Ryobi Technologies, Inc. and
found in the reasonable judgment of Ryobi Technologies,
Inc. to be defective in material or workmanship will be
repaired or replaced by an authorized Ryobi Technologies,
Inc. service dealer without charge for parts and labor.

The product, including any defective part, must be returned
to an authorized service dealer within the warranty period.
The expense of delivering the Ryobi Technologies, Inc.
product to the dealer for warranty work and the expense
of returning it back to the owner after repair or replacement
will be paid by the owner. Ryobi Technologies, Inc.’s
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach
of warranty shall be cause for cancellation or rescission
of the contract of sale of any Ryobi Technologies, Inc.
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by an authorized Ryobi Technologies, Inc.
service dealer.

This warranty is limited to ninety (90) days from the date
of original retail purchase for any Ryobi Technologies, Inc.
product that is used for rental or commercial purposes, or
any other income-producing purpose.

This warranty does not cover any Ryobi Technologies,
Inc. product that has been subject to misuse, neglect,
negligence, or accident, or that has been operated in any
way contrary to the operating instructions as specified
in this operator’s manual. This warranty does not apply
to any damage to the Ryobi Technologies, Inc. product
that is the result of improper maintenance or to any
Ryobi Technologies, Inc. product that has been altered
or modified. The warranty does not extend to repairs
made necessary by normal wear or by the use of parts or
accessories which are either INCOMPATIBLE WITH THE
RYOBI TECHNOLOGIES, INC. product or adversely affect
its operation, performance, or durability.

In addition, this warranty does not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bag
and Straps, Guide Bars, Saw Chains

Ryobi Technologies, Inc. reserves the right to change or
improve the design of any Ryobi Technologies, Inc. product
without assuming any obligation to modify any product
previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
AN Y SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY
DAY WARRANTY PERIOD. RYOBI TECHNOLOGIES,
INC.’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR
OR REPLAC EMENT OF DEFECTIVE PARTS AND
RYOBI TECHNOLOGIES, INC.DOES NOT ASSUME OR
AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. RYOBI TECHNOLOGIES, INC. ASSUMES NO
RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,
OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED TO,
EXPENSE OF RETURNING THE RYOBI TECHNOLOGIES,
INC. PRODUCT TO AN AUTHORIZED SERVICE DEALER
AND EXPENSE OF DELIVERING IT BACK TO THE OWNER,
MECHANIC’S TRAVEL TIME, TELEPHONE OR TELEGRAM
CHARGES, RENTAL OF A LIKE PRODUCT DURING THE
TIME WARRANTY SERVICE IS BEING PERFORMED,
TRAVEL, LOSS OR DAMAGE TO PERSONAL PROPERLY,
LOSS OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.

This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

This warranty applies to all Ryobi Technologies, Inc.
products manufactured by Ryobi Technologies, Inc. and
sold in the United States and Canada.

To locate your nearest service dealer, dial 1-800-860-4050.

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.

RYOBI TECHNOLOGIES, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION
CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Ryobi Technologies, Inc. are pleased
to explain the Emission Control System Warranty on your non-road or small off-road engine. In California, new small off-road engines
must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model
year non-road engines must be designed, built, and equipped, at the time of sale, to meet the U.S. EPA regulations for small non-road
engines. The non-road engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA
standards for the first two years of engine use from the date of sale to the ultimate purchaser. Ryobi Technologies, Inc. must warrant
the emission control system on your non-road or small off-road engine for the period of time listed above provided there has been no
abuse, neglect, or improper maintenance of your non-road or small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic
converter. Also included may be hoses, belts and connectors, and other emission related assemblies.

Where a warrantable condition exists, Ryobi Technologies, Inc. will repair your non-road or small off-road engine at no cost to you,
including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year non­road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or
replaced by Ryobi Technologies, Inc. free of charge.

OWNER’S WARRANTY RESPONSIBILITIES

(a) As the non-road or small off-road engine owner, you are responsible for the performance of required maintenance listed in your

operator’s manual. Ryobi Technologies, Inc. recommends that you retain all receipts covering maintenance on your non-road or
small off-road engine, but Ryobi Technologies, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability
may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.

(b) As the non-road or small off-road engine owner, you should be aware, however, that Ryobi Technologies, Inc., may deny you

warranty coverage if your non-road or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or
unapproved modifications.

(c) You are responsible for presenting your non-road or small off-road engine to a Ryobi Technologies, Inc., service dealer as soon as

a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a Ryobi Technologies, Inc., Customer
Representative at 1-800-860-4050.

COVERAGE:

Ryobi Technologies, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your non-road or small off-road
engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Ryobi Technologies, Inc. also war­rants to the initial purchaser and each subsequent purchaser that your non-road or small off-road engine is free from defects in mate­rials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and
later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires
manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the non-road or small off­road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by
Ryobi Technologies, Inc. at no cost to the owner.

Ryobi Technologies, Inc. shall remedy warranty defects at any authorized Ryobi Technologies, Inc. engine dealer or warranty sta­tion. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work deter­mines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty
maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty.
Ryobi Technologies, Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s
regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)

These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.

MAINTENANCE REQUIREMENTS

The owner is responsible for the performance of the required maintenance as defined by Ryobi Technologies, Inc. in the operator’s
manual.

LIMITATIONS

The Emission Control Systems Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or

replacements not conforming to Ryobi Technologies, Inc. specifications that adversely affect performance and/or durability, and
alterations or modifications not recommended or approved in writing by Ryobi Technologies, Inc., and

(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled

replacement point.

The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which
the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.

24 25

1-800-8 60-4050

CALL

WARRANTY

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER

Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every

Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours
or Yearly or Yearly

CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X

AIR FILTER ASSY

includes:

Filter ................................................................. X............................. X

SPARK SCREEN ..................................................................................................................X

CARBURETOR ASSY

includes:
Heat Dam
Gaskets

FUEL TANK ASSY

includes:

Fuel Lines........................ X

Fuel Cap.......................... X

Fuel Filter

IGNITION ASSY

includes:

Spark Plug........................................................................................ X

ALL EMISSIONS RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

CALL US FIRST

For any questions about operating or maintaining your product,

call the Ryobi® Help Line!

Your product has been fully tested prior to shipment to ensure

your complete satisfaction.

OPERATOR’S MANUAL

PC30 PRUNER/TRIMMER

RY52002

WARNING:

The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.

CALIFORNIA PROPOSITION 65

• SERVICE

Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi
Authorized Service Center. You can also check our web site at www.ryobitools.com for a
complete list of Authorized Service Centers.

• MODEL NO. AND SERIAL NO.

The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.

• HOW TO ORDER REPAIR PARTS

When ordering repair parts, always give the following information:

• MODEL NUMBER

• SERIAL NUMBER

RYOBI TECHNOLOGIES, INC.

1428 Pearman Dairy Road, Anderson, SC 29625

Post Office Box 1207, Anderson, SC 29622-1207

RY52002

Phone [phone]

983000-700

4-05