Ryobi RBV3000CESV User Manual
RBV3000CESV
ORIGINAL INSTRUCTIONS
Electric Blower/
Vacuum
Important!
It is essential that you read the instructions in this manual before assembling,
operating and maintaining this machine.
Subject to technical modification.
WARNING
When using the product, the safety rules must be
followed. For your own safety and that of bystanders, you
must read and fully understand these instructions before
operating the product. Please keep these instructions
safe for later use.
WARNING
This power tool is not intended to be used by children
or persons with reduced physical, mental or sensory
capabilities. Children should be adequately supervised
to ensure they do not play with the power tool.
GENERAL SAFETY WARNINGS
TRAINING
Ŷ Read the instructions carefully. Be familiar with the
controls and the correct use of the product.
Ŷ Never allow children, persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge or people unfamiliar with these instructions
to use the product. Local regulations may restrict the
age of the operator.
Ŷ Keep in mind, that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
Ŷ Keep bystanders, children and pets 15 m away from
the area of operation. Stop the product if anyone enters
the area.
Ŷ Never use the product when you are tired, ill or under
the influence of alcohol, drugs or medicine.
ELECTRICAL SAFETY
Ŷ Power plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Ŷ Avoid unintentional starting. Always check that the
switch is in the Off position before plugging in the
product to the power supply. Do not carry a plugged in
product with your finger on the switch.
Ŷ Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Ŷ Do not expose this product to rain or wet conditions.
Water entering an appliance will increase the risk of
electric shock.
Ŷ Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 mA.
Ŷ Before every use, examine the power cord for damage.
If there are signs of damage, it must be replaced by at
an authorised service centre. Always uncoil the power
cord during use; coiled cables can overheat.
Ŷ If you need to use an extension cord ensure it is suitable
for outdoor use and has a current capacity rating
sufficient to supply your tool. The extension cord cable
should be marked with either “H05 RN F” or “H05 VV F”.
Check the extension cord before every use for damage.
Always uncoil the extension cord during use because
coiled cords can overheat. Damaged extension cords
should not be repaired, they should be replaced with
an equivalent type.
Ŷ Make sure the power cord is positioned so that it will not
be stepped on, tripped over or otherwise subjected to
damage or stress.
Ŷ Never pick up or carry the product by the electric cable.
Ŷ Never pull by the power cord to disconnect from the
power supply.
Ŷ Keep the power cord away from heat, oil and sharp
edges.
Ŷ Always direct the cable to the rear away from the
machine.
Ŷ Make sure voltage is correct for your product. A
nameplate on the product indicates the unit’s voltage.
Never connect the product to an AC voltage that differs
from this voltage.
Ŷ Make sure the switch is in Off position before
disconnecting from power supply.
PREPARATION
Ŷ Some regions have regulations that restrict the use of
the product to some operations. Check with your local
authority for advice.
Ŷ While operating the product always wear substantial
footwear and long trousers. Do not operate the product
when barefoot or wearing open sandals. Avoid wearing
clothing that is loose fitting or that has hanging cords or
ties; they can be caught in moving parts.
Ŷ Do not wear loose clothing or jewellery that can be
drawn into the air inlet.
Ŷ Secure long hair so it is above shoulder level to prevent
entanglement in moving parts.
Ŷ Wear hearing protection at all times whilst operating the
product. This product is extremely noisy and permanent
hearing may result if precautions to limit your exposure,
reduce noise and wear hearing protection are not
strictly adhered to.
Ŷ Wear full eye protection at all times whilst operating this
product. The manufacturer strongly suggests a full face
mask or fully enclosed goggles. Normal spectacles or
sun glasses are not adequate protection. Objects can
be thrown at high speed by the powerful air jet at any
time and may rebound from hard surfaces toward the
operator.
Ŷ Ensure before each use that all controls and safety
devices function correctly. Do not use the tool if the “off”
switch does not stop the product.
Ŷ Before each use, always visually inspect to see, that the
housing is undamaged and that guards and handles are
in place and properly secured.
Ŷ Return to an authorised service centre to replace
damaged or unreadable labels.
Ŷ Never operate the appliance with defective guards or
shields, or without safety devices, for example debris
1
collector in place.
Ŷ Keep all cooling air inlets clear of debris.
Ŷ Use rakes and brooms to loosen debris before blowing/
vacuuming.
Ŷ Clear the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or
string which can be blown a considerable distance by
high velocity air.
WARNING
Before using the product in vacuum mode you must
assemble the upper and lower vacuum tubes together
as shown on page 7. This is a once only operation.
Never operate the vacuum with only the upper vacuum
WXEH ¿WWHG 7KH ULVN RI SHUVRQDO LQMXU\ LV VLJQL¿FDQWO\
increased if you fail to follow this warning.
OPERATION
Ŷ If the cord becomes damaged during use, disconnect
the cord from the power supply immediately. Do not
touch the cord before disconnecting the power
supply. Do not use the product if the cord is damaged
or worn.
Ŷ Operate the product only at reasonable hours – not
early in the morning or late at night when people might
be disturbed.
Ŷ Never operate the product in an explosive atmosphere.
Ŷ Avoid using the product in bad weather conditions
especially when there is a risk of lightning.
Ŷ Do not operate in poor lighting. The operator requires a
clear view of the work area to identify potential hazards.
Ŷ Use of hearing protection reduces the ability to hear
warnings (shouts or alarms). The operator must pay
extra attention to what is going on in the working area.
Ŷ Do not get distracted and always concentrate on what
you are doing. Think about and consider the effect of
your actions carefully.
Ŷ Operating similar tools nearby increases both the risk
of hearing injury and the potential for other persons to
enter your working area.
Ŷ Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance.
Ŷ Always be sure of the footing on slopes and walk, never
run.
Ŷ Keep all parts of your body away from any moving part.
Rotating impeller blades can cause severe injury. Stop
the product and ensure impeller blades have stopped
rotating before opening the fan cover, installing or
changing tubes, opening or removing debris bag.
Ŷ Never run the product without the proper equipment
attached. When used as a blower, always install the
blower tubes and close the fan cover. When used as a
vacuum, always install the vacuum tubes and vacuum
bag.
Ŷ Do not modify the product in any way or use parts
and accessories which are not recommended by the
manufacturer.
WARNING
If the product is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the product and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
Ŷ To reduce the risk of injury associated with contacting
rotating parts, always stop the product, disconnect from
the mains, and make sure all moving parts have come
to a stop:
Ɣ before cleaning or clearing a blockage
Ɣ when leaving the product unattended
Ɣ before installing or removing attachments
Ɣ before checking, maintenance or working on the
product
Ɣ after striking a foreign object to inspect the product
for damage
Ɣ if the product starts to vibrate abnormally (inspect
immediately)
WARNING
Your blower/vacuum may be supplied with a harness.
Carefully adjust the harness to comfortably help to
support the weight of the product.
Identify the quick release mechanism and practice using
it before you start using the product. Its correct use may
prevent serious injury in the case of an emergency. Never
wear additional clothing over the harness or otherwise
restrict access to the quick release mechanism.
BLOWER SAFETY WARNINGS
Ŷ Wear a face filter mask in dusty conditions to reduce
the risk of injury associated with the inhalation of dust.
Ŷ Do not point the blower nozzle in the direction of people
or pets.
Ŷ Never place objects inside the blower tubes.
Ŷ Do not operate the product near open windows, etc.
Ŷ Slightly dampen surfaces in dusty conditions.
Ŷ Use the full blower nozzle extension so the air stream
can work close to the ground.
Ŷ Do not place blower on top of or near loose debris.
Debris may be sucked into intake vent resulting in
possible damage to the product.
VACUUM SAFETY WARNINGS
WARNING
Never operate the vacuum with only the upper vacuum
WXEH ¿WWHG 7KH ULVN RI SHUVRQDO LQMXU\ LV VLJQL¿FDQWO\
increased if you fail to follow this warning.
Ŷ Do not operate vacuum without vacuum bag assembly
installed; flying debris could cause serious injury. Make
sure the vacuum bag is completely zipped closed
2
before operating.
Ŷ Move the vacuum from side to side along outer edge of
debris. To avoid clogging, do not place the vacuum tube
directly into the debris pile.
Ŷ Hold the motor higher than the inlet end of the vacuum
tube.
Ŷ Always point vacuum tube downhill when working on
a hillside.
Ŷ To avoid serious injury to the operator or damage to the
product, do not try to vacuum up rocks, broken glass,
bottles, or other similar objects.
Ŷ Avoid situations that could cause fire in the vacuum
bag. Do not operate near an open flame. Do not
vacuum warm ash from fireplaces, barbecue pits, etc.
Do not vacuum discarded cigars or cigarettes unless
the cinders are completely cool.
TRANSPORTATION AND STORAGE
Ŷ Stop the product, disconnect from the mains and allow
it to cool before storing or transporting.
Ŷ Clean all foreign material from the product. Store it in a
cool dry and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents such
as garden chemicals and de-icing salts. Do not store
outdoors.
Ŷ For transportation, secure the product against
movement or falling to prevent injury to persons or
damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts,
accessories and attachments. Failure to do so can
cause possible injury, poor performance and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
DQG VKRXOG EH SHUIRUPHG RQO\ E\ D TXDOL¿HG VHUYLFH
technician. For service we suggest you return the
product to your nearest authorised service centre for
repair. When servicing, use only identical replacement
parts.
Ŷ You may make adjustments and repairs described
here. For other repairs, contact the authorised service
agent.
Ŷ After each use, clean the product with a soft dry cloth.
Ŷ Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
centre.
INTENDED USE
The product is only intended for use outdoors.
This product is not intended to be used by children
or persons with reduced physical, mental or sensory
capabilities.
The product is intended for blowing light debris including
leaves, grass and other garden refuse. It is intended to
vacuum and lightly mulch debris as described above and
deposit it into the collection bag. It is not designed to suck
or vacuum water or other liquid.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Ŷ Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
Ŷ Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
Ŷ Injury from flying objects from the blow tube airflow or
vacuum exhaust if the bag is not fitted or damaged.
Wear adequate eye protection at all times.
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
QXPEQHVV DQG EODQFKLQJ RI WKH ¿QJHUV XVXDOO\ DSSDUHQW
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Ŷ Keep your body warm in cold weather. When operating
the product wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
Ŷ After each period of operation, exercise to increase
blood circulation.
Ŷ Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
See page 6.
1. Fan cover
2. Upper vacuum tube
3. Lower vacuum tube
4. Guide wheels
5. High speed nozzle
3
6. Lower blow tube
7. Upper blow tube
8. Vacuum bag
9. Bag adaptor
10. Blower/vacuum mode selection lever
11. Front handle
12. Speed selector
13. Rear handle
14. On/Off trigger
Vacuum mode
SYMBOLS IN THIS MANUAL
Connect to power outlet.
SYMBOLS ON THE PRODUCT
Read and understand all instructions
before operating the product, follow all
warnings and safety instructions.
%HZDUHRIWKURZQRUÀ\LQJREMHFWV
Keep all bystanders, especially
children and pets, at least 15 m away
from the operating area.
Rotating fans. Keep hands and feet
out of openings while the product is
running.
Wear ear protection.
Wear eye protection.
Do not expose to rain or damp
condition.
Switch off: remove plug from mains
before cleaning or maintenance
Remove plug from the mains
immediately before maintenance or if
cable is damaged or cut.
Conforms to all regulatory standards
in the country in the EU where the
product is purchased.
Disconnect from power outlet.
Note
Warning
The following signal words and meanings are intended to
explain the levels of risk associated with this product.
DANGER
Indicates an imminently hazardous situation, which, if
not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CAUTION
Without safety alert symbol
Indicates a situation that may result in property damage.
GOST-R Conformity
Class II tool, double insulation
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
The guaranteed sound power level is
108
shown on this label by 108 dB.
Blower mode
4
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
5
11 12
1
2
3
654 7 8 9 10
13
14
6
Loading...