Ryobi P360 User Manual [en, fr, es]
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
18 V AirStrike™ STAPLER
AGRAFEUSE DE AirStrike™ 18 V
GRAPADORA DE AirStrike™ 18 V
P360
TABLE OF CONTENTS
****************
General Power Tool
Safety Warnings ..............................2-3
Stapler Safety Warnings ..................3-5
Symbols ..............................................6
Glossary .............................................7
Features .............................................. 7
Assembly ............................................ 7
Operation .......................................8-10
Maintenance ..................................... 11
Troubleshooting ................................ 11
Illustrations ..................................12-13
Parts Ordering
and Service ........................Back page
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
TABLE DES MATIÈRES
****************
Avertissements de sécurité générales
relatives aux outils électriques ........2-3
Avertissements de sécurité relatifs
agrafeuse ........................................3-5
Symboles ............................................6
Glossaire .............................................7
Caractéristiques .................................7
Assemblage ........................................ 7
Utilisation ......................................8-10
Entretien ...........................................11
Dépannage ....................................... 11
Illustrations ..................................12-13
Commande de pièces
et dépannage ...................Page arrière
AVERTISSEMENT :
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
Pour
ÍNDICE DE CONTENIDO
****************
Advertencias de seguridad generales
para herramientas eléctrica ........... 2-3
Advertencias de seguridad de
grapadora de puntillas ................... 3-5
Símbolos ............................................6
Glosario de términos .........................7
Características ...................................7
Armado ..............................................7
Funcionamiento ........................... 8-10
Mantenimiento .................................11
Corrección de problemas ................11
Illustraciones .............................. 12-13
Pedidos de piezas
y servicio ....................... Pág. posterior
ADVERTENCIA: Para
reducir el riesgo de lesiones, el usuario
debe leer y comprender el manual del
operador antes de usar este producto.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
Use battery only with charger listed. For use with 18V
nickel-cadmium and 18V lithium-ion battery packs,
see tool/appliance/battery pack/charger correlation
supplement 987000-432.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
2 — English
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
GENERAL POWER TOOL SAFETY WARNINGS
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
STAPLER SAFETY WARNINGS
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
Always assume that the tool contains fasteners. Care-
less handling of the stapler can result in unexpected firing
of staples and personal injury.
Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the staple
causing an injury.
Do not actuate the tool unless the tool is placed firmly
against the workpiece. If the tool is not in contact with
the workpiece, the staple may be deflected away from
your target.
Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
Use caution while removing a jammed staple. The
mechanism may be under compression and the staple
may be forcefully discharged while attempting to free a
jammed condition.
Do not use this tool for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well as
the specific potential hazards related to this power
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Everyday glasses have only
impact resistant lenses. They are not safety glasses. Following this rule will reduce the risk of serious personal
injury.
Eye protection which conforms to ANSI specifications
and provides protection against flying particles both
from the FRONT and SIDE should ALWAYS be worn
by the operator and others in the work area when
loading, operating or servicing this tool. Eye protection
is required to guard against flying fasteners and debris,
which could cause severe eye injury.
The employer and/or user must ensure that proper
eye protection is worn. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety
glasses that provide protection against flying particles
both from the front and side. Always use eye protection
which is marked to comply with ANSI Z87.1.
3 — English
STAPLER SAFETY WARNINGS
Additional safety protection will be required in some
environments. For example, the working area may in-
clude exposure to noise level which can lead to hearing
damage. The employer and user must ensure that any
necessary hearing protection is provided and used by the
operator and others in the work area. Some environments
will require the use of head protection equipment. When
required, the employer and user must ensure that head
protection conforming to ANSI Z89.1-1997 is used.
Keep fingers away from trigger when not driving fasteners to avoid accidental firing
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an elec-
trical outlet; therefore, they are always in operating
condition. Be aware of possible hazards when not
using your battery tool or when changing accessories.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and pos-
sibly injury.
Use the tool only for its intended use. Do not discharge
fasteners into open air.
Use the tool only for the purpose for which it was
designed.
Use only the staples recommended for this tool. Use
of the wrong staples could result in poor staple feeding,
jammed staples, and staples leaving the tool at erratic
angles. If staples are not feeding smoothly and properly,
discontinue their use immediately. Jammed and improperly feeding staples could result in serious personal injury.
Never use this tool in a manner that could cause a
fastener to be directed toward anything other than
the workpiece.
Do not use the tool as a hammer.
Always carry the tool by the handle.
Do not alter or modify this tool from the original design
or function without approval from the manufacturer.
Always be aware that misuse and improper handling
of this tool can cause injury to yourself and others.
Never clamp or tape the trigger or workpiece contact
in an actuated position.
.
Never leave tool unattended if the battery is installed.
Do not operate this tool if it does not contain a legible
warning label.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Following this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
OPERATION
Do not use tool if trigger does not actuate properly.
Any tool that cannot be controlled with the trigger is
dangerous and must be repaired.
Check operation of the workpiece contact mechanism
frequently. Do not use the tool if the workpiece contact
mechanism is not working correctly as accidental driving
of a fastener may result. Do not interfere with the proper
operation of the workpiece contact mechanism.
Do not use a tool that does not work correctly.
Always assume that the tool contains fasteners.
Do not carry the tool from place to place holding the
trigger. Accidental discharge could result.
Always handle the tool with care:
• Respect the tool as a working implement.
• Never engage in horseplay.
• Never pull the trigger unless nose is directed toward the
work.
• Keep others a safe distance from the tool while tool is in
operation as accidental actuation may occur, possibly
causing injury.
Choice of triggering method is important. Check
manual for triggering options.
The stapler is designed for single-hand use. Do not
hold the tool by the front of the magazine. Do not put
hands, head, or other parts of your body near the bottom
of the magazine where the staple exits the tool, as serious
personal injury could result.
Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
Do not actuate the tool unless you intend to drive a
fastener into the workpiece.
Always ensure that the workpiece contact is fully posi-
tioned above the workpiece. Positioning the workpiece
contact only partially above the workpiece could cause
the fastener to miss the workpiece completely and result
in serious personal injury.
4 — English
STAPLER SAFETY WARNINGS
Do not drive fasteners near edge of material. The
workpiece may split causing the fastener to ricochet,
injuring you or a co-worker. Be aware that the fastener
may follow the grain of the wood, causing it to protrude
unexpectedly from the side of the work material or deflect, possibly causing injury.
Keep hands and body parts clear of immediate work
area. Hold workpiece with clamps when necessary to
keep hands and body out of potential harm. Be sure the
workpiece is properly secured before pressing the fastener against the material. The workpiece contact may
cause the work material to shift unexpectedly.
Keep face and body parts away from back of the tool
cap when working in restricted areas. Sudden recoil
can result in impact to the body, especially when driving
fasteners into hard or dense material.
During normal use the tool will recoil immediately
after driving a fastener. This is a normal function of
the tool. Do not attempt to prevent the recoil by holding
the stapler against the work. Restriction to the recoil can
result in a second fastener being driven from the stapler.
Grip the handle firmly, let the tool do the work and do not
place second hand on top of tool or near exhaust at any
time. Failure to heed this warning can result in serious
personal injury.
Do not drive fasteners on top of other fasteners or with
the tool at an overly steep angle as this may cause
deflection of fasteners which could cause injury.
LOADING TOOL
Do not load the tool with fasteners when any one of the
operating controls is activated.
When loading tool:
Never place a hand or any part of body in fastener dis-
charge area of tool.
Never point tool at anyone.
Do not pull the trigger or depress the workpiece contact
as accidental actuation may occur, possibly causing
injury.
SAVE THESE INSTRUCTIONS
Refer to them frequently and use them to instruct others
who may use this tool. If you loan someone this tool, loan
them these instructions also.
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities
may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
5 — English
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
NOTICE:
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s
Manual
Eye Protection
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Always wear eye protection with side shields marked to comply with ANSI
Z87.1.
Keep Hands Away Keep hands and body away from the discharge area of the tool.
Wet Conditions
Alert
Recycle Symbols
V Volts Voltage
min Minutes Time
Direct Current Type or a characteristic of current
n
o
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
No Load Speed Rotational speed, at no load
Do not expose to rain or use in damp locations.
This product uses nickel- cadmium (Ni-Cd) and lithium-ion (Li-ion) batteries.
Local, state or federal laws may prohibit disposal of batteries in ordinary
trash. Consult your local waste authority for information regarding available
recycling and/or disposal options.
6 — English
GLOSSARY
Activate (operating controls)
To move an operating control so that it is in a position that
allows the tool to be actuated or that satisifes one requirement
for the tool to be actuated.
Actuate (tool)
To cause movement of the tool component(s) intended to
drive a fastener.
Actuation system
The use of a trigger, workpiece contact, and/or other operating
control, separately or in some combination or sequence, to
actuate the tool.
• Single sequential actuation
An actuation system in which there is more than one
operating control and the operating controls must be
activated in a specific sequence to actuate the tool.
Additional actuation can occur when a specific operating
control, other than a workpiece contact, is released and
re-activated.
• Contact actuation
An actuation system in which there is more than one
operating control and the operating controls can be
activated in any sequence to actuate the tool. Additional
actuation can occur when any operating control is
released and re-activated.
Fastener
A staple, pin, brad, nail, or other fastening device which is
designed and manufactured for use in the tools within the
scope of this standard.
Jam
An obstruction in the feed or drive areas of the tool.
Operating control
A control that separately, or as part of an actuation system,
can cause the actuation of a tool.
Trigger
A tool operating control activated by a tool operator’s fingers.
Workpiece
The intended object into which a fastener is to be driven
by a tool.
Workpiece contact
An operating control element or assembly on the tool intended
to be activated by the material to be fastened.
FEATURES
PRODUCT SPECIFICATIONS
Magazine Capacity ...........................................105 Staples
Stapler Speed .......................................up to 60 shots/min.
Staple Type ............................ 1/4 in. Narrow Crown Staple
Staple Size (Length) ................................ 3/8 in to 1-1/2 in.
ASSEMBLY
WARNING:
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of
a product that is not properly and completely assembled
or with damaged or missing parts could result in serious
personal injury.
If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
WARNING:
Do not attempt to modify this product or create
accessories or attachments not recommended for use
with this product. Any such alteration or modification is
misuse and could result in a hazardous condition leading
to possible serious personal injury.
7 — English
OPERATION
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always remove battery pack from the tool when you are
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental
starting that could cause serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
APPLICATIONS
You may use this tool for the purposes listed below:
Finish and Trim (Interior and exterior)
Door & Window Casing
Door Jambs
Baseboard
Crown Molding
Cabinetry
Cap and Shoe Molding
Molding
Staircases
Door and Window Trim
Chair Rail
Brickmold
Hardwood Flooring
Paneling
Furniture
ATTACH BELT CLIP
See Figure 1, page 12.
The belt clip can be installed on the left or right side of the
stapler, depending on operator preference.
Alignbeltclipandscrewwithrightorleftsidescrewhole.
Usinga phillips screwdriver (not included)tighten se-
curely.
INSTALLING/REMOVING BATTERY PACK
See Figure 2, page 12.
To install, place the battery pack in the tool. Align the
raised rib inside the tool with the groove on the battery
pack.
Make sure the latches on each side of the battery pack
snap into place and battery pack is secured in tool before
beginning operation.
NOTE: Squeeze LED light grip switch to activate stapler.
To remove battery pack:
To remove, locate latches on battery pack and depress
to release battery pack from the tool.
For complete charging instructions, see the operator’s
manuals for your battery pack and charger.
NO-MAR PAD
See Figure 3, page 12.
The no-mar pad attached to the nose of the tool helps prevent marring and denting when working with softer woods.
To remove or replace the pad:
Remove the battery pack.
Remove the pad by pulling it down and away from the
nose.
To replace the pad, fit it into place over the nose and
push up to reseat.
On-board storage for the pad is located on the magazine of
the tool. An extra no-mar pad is provided in the on-board
storage area.
LOADING THE TOOL WITH STAPLES
See Figures 4 - 5, pages 12 - 13.
WARNING:
Use only the staples recommended for use with this tool.
The use of any other staples can result in tool malfunction,
leading to serious injuries.
WARNING:
Keep the tool pointed away from yourself and others
when loading fasteners. Failure to do so could result in
possible serious personal injury.
Remove battery pack from the tool, if installed.
Hold the tool upside down with the nose pointed upward
and tilted away from you.
Squeeze the magazine release button located at the rear
of the magazine and slide the magazine cover open.
Place staples in the channel with the staple tips point-
ing upward and the crown resting on the bottom of the
channel.
8 — English
OPERATION
Push the magazine cover closed. Make sure it securely
snaps into place.
Reinstall battery, and reactivate the tool by pressing the
worklight grip switch.
REMOVING STAPLES FROM THE TOOL
Remove the battery pack.
Depress the magazine release button.
Remove staples and close the magazine.
SETTING THE AIR PRESSURE
See Figure 6, page 13.
The amount of air pressure required will depend on the size
of the fastener and the workpiece material.
Begin testing the depth of drive by driving a test fastener into
the same type of workpiece material used for the actual job.
Remove battery pack from the tool, if installed.
Turn air pressure dial clockwise to increase air pressure
or counterclockwise for decreased pressure.
It may be possible to achieve the desired depth with air
pressure adjustments alone. If finer adjustments are needed,
use the depth of drive adjustment on the tool.
NOTE: Under some conditions, the unit may not deliver a
fastener when the air pressure dial is turned to the MAXIMUM pressure setting. The user may need to decrease the
pressure setting for desired operation.
ADJUSTING DEPTH OF DRIVE
See Figure 7, page 13.
The driving depth of the fastener may be adjusted beyond
air pressure. It is advisable to test the depth on a scrap
workpiece to determine the required depth for the application.
To determine depth of drive, first adjust the air pressure and
drive a test fastener. To achieve the desired depth, use the
depth of drive adjustment on the tool. Harder materials and
longer fasteners will require more force to drive the staple.
Remove battery pack from the tool, if installed.
Turn the depth of drive adjustment left or right to change
the driving depth.
Reinstall battery and reactivate the tool by pressing the
worklight grip switch.
Drive a test staple after each adjustment until the desired
depth is set.
NOTE: Set depth of drive at the shallowest depth that
will meet your needs.
DRIVING STAPLES
See Figures 8 - 9, page 13.
WARNING:
Never wedge or hold back the workpiece contact mechanism during operation of the tool. Doing so could result
in possible serious injury.
The mode selector lets the operator choose between Single
Sequential Actuation for precise fastener placement and
Contact Actuation for higher productivity.
The tool will drive a fastener each time the trigger is depressed,
as long as the workpiece contact is depressed.
Single sequential actuation mode:
Single sequential actuation provides the most accurate
fastener placement.
Remove battery pack from the tool.
Slide the selector to position ( ).
WARNING:
The stapler will not function properly if the selector is not securely seated in either position ( ) or
( ). Always assure the selector is seated properly to
avoid an unexpected fastener discharge and possible
serious personal injury.
Reinstall the battery and reactivate the tool.
Grip the tool firmly to maintain control. Position the nose
of the tool onto the work surface.
Push the tool against the work surface to depress the
workpiece contact.
Squeeze the trigger to drive a fastener.
NOTE: Hold trigger until drive cycle is complete.
Always remove your finger from the trigger when the
desired number of fasteners has been driven.
9 — English
OPERATION
Contact actuation mode:
Contact actuation allows very fast repetitive fastener placement.
Remove battery pack from the tool.
Slide the selector to position ( ).
Reinstall the battery and reactivate the tool.
Grip the tool firmly to maintain control.
Squeeze and hold the trigger. Push the tool against the
work surface to depress the workpiece contact and drive
a staple.
Lift the tool from the workpiece to drive the next staple.
NOTE: Hold trigger until drive cycle is complete.
Always remove your finger from the trigger when the
desired number of fasteners has been driven.
NOTE: In Contact Actuation Mode, the tool may also be
operated by depressing the workpiece contact against the
surface and squeezing the trigger.
DRY-FIRE LOCKOUT
The dry-fire lockout feature keeps the tool from operating
when fasteners are low in the magazine.
The low staple indicator window in the magazine shows
how many staples remain in the tool.
When the magazine has 0-5 staples remaining, the dry-fire
lockout feature will not allow continued operation.
To resume operation, reload the tool with staples.
REMOVING A JAMMED STAPLE
See Figure 11, page 13.
WARNING:
Remove the battery pack before removing staples or
clearing a jammed staple. Failure to do so could result
in serious personal injury.
Remove the battery pack from the tool.
Open the magazine and remove staples.
Insert a flat blade screwdriver into the driving mechanism
and push the driver mechanism back, freeing the jam.
Remove the bent staple.
Reinsert staples and close the magazine.
Reinstall the battery and reactivate the tool.
NOTE: Driving too deeply into the material, excess debris,
or jammed fasteners may lead to a driver blade being stuck
at its bottom position.
CONSTRUCTION RULER
A construction ruler located along the left side of the magazine allows the operator to make quick measurements while
working.
LED WORKLIGHTS/DIAGNOSTIC FEEDBACK
See Figure 10, page 13.
The LED Worklights provide feedback to indicate whether
the battery pack is charged sufficiently and/or if the tool is
functioning properly.
To turn on the worklights, press the LED worklight grip switch
while firmly holding tool in normal operating position.
If worklights are flashing, install fully charged battery. If
lights continue to flash, see Troubleshooting section for
more information.
10 — English
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Work-contacting element does not
depress fully - tool does not operate.
Tool operates properly, but fasteners do
not drive fully
Tool operates properly, but fasteners are
driven too deep
Tool jams frequently Incorrect staples
Tool stops and LEDs flash rapidly Battery is low or has no charge
Tool has charged battery and LEDs
are slowly flashing or LEDs do not turn
off after approximately ten seconds of
non-use.
Low staples
Work-contacting element is jammed
Air pressure is too low
Depth of drive isn’t deep enough
Staple is too long for wood hardness
Air pressure is too high
Depth of drive is too deep
Damaged staples
Loose magazine
Dirty magazine
Tool is hot
Tool has malfunctioned Take tool to nearest authorized repair
Replenish staples
Remove battery and clear debris
Increase air pressure
Adjust depth of drive
Use staple length that is appropriate
for wood
Decrease air pressure
Adjust depth of drive
Verify that staples are the correct size
Replace staples
Tighten screws
Clean magazine
Recharge battery
Allow tool to cool
center
NOTE: ILLUSTRATIONS START ON PAGE 12
AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
11 — English
Loading...