Russound VMR1 User Manual

Safety Precautions

1. Read these instructions.

2. Keep these instructions

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accor­dance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifi ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or
grounding plug. A polarized plug has two blades with
one wider than the other. A grounding plug has two
blades and a third grounding prong. The wide blade
or the third prong is provided for your safety. If the
provided plug does not fi t into your outlet, consult an
electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where it exits from the apparatus.

11. Use only attachments or accessories specifi ed by the
manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table
specifi ed by the manufacturer or sold with the appara­tus. When a cart is used, use caution when moving the
cart-apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when
unused for long periods of time.

14. Refer all servicing to qualifi ed service personnel. Servic­ing is required when the apparatus has been damaged
in any way, such as the power supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into the apparatus, or the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.

If you have any questions, call Russound at 800.638.8055
or 603.659.5170.

Specifi cations

Device type: Single-gang in-wall Decora®-style
Input connector: 110 punch-down block
System cable: CAT-5e
Maximum cable length: 300 ft (90 m)
Output connectors: (3) RCA jacks for component video
Video resolution: Up to 1080p
Dimensions: 1.75” W x 4.17” H x 1.31” D

(4.4 x 10.6 x 3.3 cm)
Weight: 2.2 oz (61.3 g)

Warranty

The Russound VMR1 is fully guaranteed against all defects in materials and
workmanship for two (2) years from the date of purchase. During this period,
Russound will replace any defective parts and correct any defect in workman­ship without charge for either parts or labor. For this warranty to apply, the unit
must be installed and used according to its written instructions. If service is
necessary, it must be performed by Russound. The unit must be returned to
Russound at the owner’s expense and with prior written permission. Acciden­tal damage and shipping damage are not considered defects, nor is damage
resulting from abuse or from servicing by an agency or person not specifi cally
authorized in writing by Russound.

This warranty does not cover: damage caused by abuse, accident, misuse,
negligence, or improper installation or operation; power surges and lightning
strikes; normal wear and maintenance; products that have been altered or
modifi ed; any product whose identifying number, decal, serial number, etc. has
been altered, defaced or removed.

Russound sells products only through authorized dealers and distributors to
ensure that customers obtain proper support and service. Any Russound prod­uct purchased from an unauthorized dealer or other source, including retailers,
mail order sellers and online sellers will not be honored or serviced under
existing Russound warranty policy. Any sale of products by an unauthorized
source or other manner not authorized by Russound shall void the warranty on
the applicable product.

Damage to or destruction of components due to application of excessive
power voids the warranty on those parts. In these cases, repairs will be made
on the basis or the retail value of the parts and labor. To return for repairs, the
unit must be shipped to Russound at the owner’s expense, along with a note
explaining the nature of service required. Be sure to pack the unit in a corru­gated container with at least three (3) inches of resilient material to protect the
unit from damage in transit.

Before returning a unit for repair, call Russound at 603.659.5170 for a return
authorization number. Write this number on the shipping label and ship to: Rus­sound, 5 Forbes Road, Newmarket, NH 03857.

5 Forbes Road, Newmarket NH 03857 USA

Tel [phone] • Fax [phone]

www.russound.com

Copyright © 2007 Russound. All rights reserved. All trademarks are the prop­erty of their respective owners. Specifi cations are subject to change without
notice. Russound is not responsible for typographical errors or omissions.
28-1238 03/08/07

VMR1

Video Matrix Receiver

Instruction Manual

Overview

The VMR1 Receiver is an in-wall device for use with the
VM1 Video Matrix to provide connections for video displays
in rooms where component video distribution is desired.
It receives distributed video signals from the Video Matrix
through a single CAT-5e cable.

The receiver provides an analog component video signal
from any source connected to the Video Matrix. Red, green,
and blue RCA jacks in a single-gang Decora
connect to the display with an RGB video cable.

The VMR1 is capable of high-defi nition video resolution up to
1080p.

®

-style wall plate

Installation

1. Run CAT-5e cable up to 300 feet (90 m) between the

VM1 and the video display locations in the zones.

Note: When running CAT-5e cables, avoid AC power wiring.
If you have to run the cables parallel to electrical wiring,
space the cable at least 12 inches (30 cm) from AC power
lines.

2. Install single-gang UL/CSA-approved plastic wall boxes

for the VMR1 receivers. Attach the boxes to the wall with
appropriate fasteners.

3. In each zone, punch down the CAT-5e cable on the back

of the VMR1 as indicated on the circuit board.

BR BR/W GRN G/W OR O/W BL BL/W

RGB video cable

110 punch-down connection on rear of VMR1

4. Insert the VMR1 into the wall box and secure it with

screws. Attach a wall plate.

5. Crimp RJ-45 connectors on the system end of the CAT-5e

cables, following the T568A standard as shown.

RJ-45 Using T568A

Wiring Standard

6. Make sure the VM1 Video Matrix is turned off. Plug the

RJ-45 connectors into the appropriate zone outputs on
the VM1. (If using wall plates, punch down the CAT-5e
per the T568A standard and use straight-through patch
cables between the VM1 and the wall plates.)

up to 300 ft (90 m)

RJ-45 wall plate
(optional)

RJ-45 patch cable

VM1 Video Matrix

CAT-5e cable

Y = Green
PB = Blue

R

= Red

P

VMR1

Typical connection of the VMR1 for one zone

Wall

Wall box CAT-5e

VMR1 Trim plate

VMR1 installation detail