Russound Pro-6, Pro-12, Pro-8 Installation Manual

1 AMP A/B 2 3 4 5 6 7 8 9 10 11 12

FAMILY ROO M

MASTER BATH

MASTER BED THEATER ROOM

OFFICE

FOYER

BEDROOM 1 BEDROOM 2 BEDROOM 3 BEDROOM 4 BEDROOM 5 BEDROOM 6

1 AMP A/B 2 3 4 5 6 7 8

FAMIL Y R OOM

GUEST BATH MASTER BATH GUEST BED MASTER BED THEATER ROOM FOYER OFFICE

1 AMP A/B 2 3 4 5 6

FAMIL Y R OOM

GUEST BATH MASTER BAT H GUEST BED MASTER BED THEATER ROOM

PRO Series

Dual Source Speaker Selectors

Installation Manual

SETUP / OPERATION /TECH SPECS / WARRANTY

Description

The PRO series speaker selectors are highly ecient dual-source, impedance­matching selectors. These high-quality speaker selectors are designed for use
with either 4-ohm or 8-ohm ampliers and 4-ohm to 8-ohm speakers.

The PRO speaker selectors are equipped with a low-frequency protection
circuit to reduce subsonic signals. This allows high power operation without
amplier shutdown. The PRO units employ audiophile-grade impedance
matching autoformers to maintain a safe operating load at the amplier while
distributing maximum power through the system. Autoformers are very ecient
because of the small loss incurred as a result of heat dissipation. The series is
equipped with a back panel rotary switch, which is used to set the appropriate
impedance based on the number of pairs of speakers connected. This switch
selects the proper taps of the autoformers, allowing all of the amplier’s power
to be delivered to the speakers.

The PRO speaker selectors can be connected to one or two ampliers. A front
panel button allows switching between the two ampliers for all speakers
connected to the unit.

Connections

The PRO series have 4-pole screw down removable terminals for speaker and
amplier connections. These accept wire up to 12 gauge.

Remove the terminal by rmly pulling it out of its 4-pole connector. Strip about
3/8” of insulation from the ends of all wires to be connected. If necessary, twist
the exposed conductor to insure that no loose strands exist. Insert the wire ends
into the screw down connector, being careful to observe proper channel and
polarity. Tighten the screws on the connector. Connect the amplier(s) and each
pair to the appropriate connector.

If external volume controls are used, connect speaker wire from the appropriate
speaker connector on the PRO to the volume control input. Speaker connections
can support multiple speaker pairs wired in parallel or series, provided their
combined impedance is a minimum of 4 ohms.

Setting System Volume

It is important to properly adjust an impedance-matching system to avoid
distortion or DC clipping (DC voltage will be produced from an amplier that is
overworked or that has an improper load). These can cause an amplier/receiver
to go into protection, and can cause autoformers on volume controls to heat
up, damaging system components. To set up the system, the amplier/receiver
volume should be at its lowest setting, and the selector volume control should
be at the highest setting. Slowly adjust the amplier/receiver volume to a level
that is acceptable for the amplier to produce without clipping.

Operation

To ensure safe operation of the amplier, an impedance level must rst be
selected using the rotary switch labeled SPEAKER PAIRS located on the rear of
the unit. This switch should be set to the total number of speaker pairs being
connected to the unit. Set the switch based on the following conditions:

If the amplier and the speakers are both 4 ohms, set the rotary switch to the •
number of pairs of speakers connected to the PRO.

If the amplier and the speakers are both 8 ohms, set the rotary switch to the •
number of pairs of speakers connected to the PRO.

If the amplier is 8 ohms and the speakers are 4 ohms, set the rotary switch •
to TWICE the number of pairs of speakers connected to the PRO.

If the amplier is 4 ohms and the speakers are 8 ohms, set the rotary switch •
to HALF the number of pairs of speakers connected to the PRO.

After setting the proper impedance level, the speakers can be turned on and
o in any combination.

To switch between the A and B ampliers, push the AMP A / AMP B button
located on the front panel.

Technical Specications

Power: 100 watts per channel RMS continuous
200 watts per channel average
300 watts per channel peak
Impedance Matching: High-eciency impedance-matching

autoformers
Low-Frequency Protection: Bi-polar capacitor circuit
Wire Size: up to 12 gauge wire
Dimensions: 17” W x 2.875” H x 8.25” D (43.2 x 7.3 x 21 cm)
Weight: PRO-6 7.52 lbs. (3.4 kg)
PRO-8 7.75 lbs. (3.49 kg)
PRO-12 7.995 lbs. (3.58 kg)

Warranty

The Russound PRO Series is fully guaranteed against all defects in materials and
workmanship for ten (10) years from the date of purchase. During this period,
Russound will replace any defective parts and correct any defect in workmanship
without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according to its
written instructions. If service is necessary, it must be performed by Russound. The
unit must be returned to Russound at the owner’s expense and with prior written
permission. Accidental damage and shipping damage are not considered defects,
nor is damage resulting from abuse or from servicing by an agency or person not
specically authorized in writing by Russound.

This Warranty does not cover:

Damage caused by abuse, accident, misuse, negligence, or improper installation •
or operation

Power surges and lightning strikes•
Normal wear and maintenance•
Products that have been altered or modied•
Any product whose identifying number, decal, serial number, etc. has been •

altered, defaced or removed.

Russound sells products only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound product
purchased from an unauthorized dealer or other source, including retailers, mail
order sellers and online sellers will not be honored or serviced under existing
Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable
product.

Damage to or destruction of components due to application of excessive power
voids the warranty on those parts. In these cases, repairs will be made on the basis of
the retail value of the parts and labor. To return for repairs, the unit must be shipped
to Russound at the owner’s expense, along with a note explaining the nature of
service required. Be sure to pack the unit in a corrugated container with at least
three (3) inches of resilient material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at [phone] for a Return
Authorization number. Write this number on the shipping label and ship to:
Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857

Due to continual eorts to improve product quality as new technology and
techniques become available, Russound/FMP, Inc. reserves the right to revise system
specications without notice.

2 Russound PRO Series Installation Manual

Rev. 5