Russound KPSC User Manual

28-1204 Rev. 1 11/02/05

Warranty Repair

The Russound KPSC is fully guaranteed against all defects in materials and
workmanship for two (2) years from the date of purchase. During this peri­od, Russound will replace any defective parts and correct any defect in
workmanship without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according to
its written instructions. If service is necessary, it must be performed by
Russound. The unit must be returned to Russound at the owner's expense
and with prior written permission. Accidental damage and shipping damage
are not considered defects, nor is damage resulting from abuse or from
servicing by an agency or person not specifically authorized in writing by
Russound.

This Warranty does not cover: Damage caused by abuse, accident, misuse,
negligence, or improper installation or operation; Power surges and light­ning strikes; Normal wear and maintenance; Products that have been
altered or modified; Any product whose identifying number, decal, serial
number, etc. has been altered, defaced or removed.

Russound sells products only through authorized Dealers and Distributors to
ensure that customers obtain proper support and service. Any Russound
product purchased from an unauthorized dealer or other source, including
retailers, mail order sellers and online sellers will not be honored or serv­iced under existing Russound warranty policy. Any sale of products by an
unauthorized source or other manner not authorized by Russound shall void
the warranty on the applicable product.

Damage to or destruction of components due to application of excessive
power voids the warranty on those parts. In these cases, repairs will be
made on the basis or the retail value of the parts and labor. To return for
repairs, the unit must be shipped to Russound at the owner's expense,
along with a note explaining the nature of service required. Be sure to pack
the unit in a corrugated container with at least three (3) inches of resilient
material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at [phone] for a
Return Authorization number. Write this number on the shipping label and
ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket, NH 03857

Due to continual efforts to improve product quality as new technology and
techniques become available, Russound/FMP, Inc. reserves the right to
revise system specifications without notice.

All trademarks are property of their respective owners.

Technical Specifications

Dimensions: 1.85"W x 2.7"D x 1"H

(4.7 x 6.9 x 2.5 cm)
Fits 1 Gang UL/CSA Approved 18 ci
Junction Box

Weight: 3 oz. (85 g)

KP Keypad Port: 12-pin connector

5 Forbes Road, Newmarket, NH 03857
tel [phone] • fax [phone]

e-mail: [e-mail]

www.russound.com

KPSC Keypad

The KPSC keypad is an in-wall, Decora®style single-gang keypad
accessory designed to connect to a KP6 or KPL keypad (wall
plate not included). The KPSC keypad provides source control and
numeric control capability to the CAA66 system keypads. It has
amber backlit, soft-touch control buttons.

Note: The KPSC keypad cannot be used with a CAS44 controller
system.

KPSC Keypad Front Panel

PRIMARY CONTROLS - Functions on outer edge of
buttons are default or normal operation for each
selected source. These include play, stop, forward,
back, pause, etc.

FAVORITES - Set and recall two favorite settings of
source and volume.

NUMERIC VALUE SHIFT - Press to shift buttons to
numeric control. Numeric Prefix “Disc” and Suffix
“Enter” commands are sent upon entering and exiting
Numeric control. Red backlight indicates numeric
mode.

NUMERIC ENTRY - Once numeric value control is
initiated, the buttons now represent the numeric
value when pressed (0-9).

Press Numeric button to enter
or exit Numeric Entry Mode

NOTE:

1. Entering Numeric Entry Mode

will send Prefix command

2. Exiting Numeric Entry Mode
will send Suffix command

Primary
source
control
function of
button is
located on
outer edge

Numeric
entry
function of
button is
located on
inner edge

KPSC Operation

The KPSC keypad adds source control and numeric con­trol capability to a KP6 or KPL keypad via a 12-pin connec­tion. The amber backlit buttons provide primary source
controls when pressed, such as stop, play, next, etc.

When the Numeric button is pressed, it becomes backlit in
red, and changes the buttons to numeric entry (0 - 9). It
will also send a Prefix command. A second press of the
Numeric button sends a Suffix command and puts the key­pad back into the source control mode. If the button is not
pressed a second time, a 3-second time out sends a
Suffix command and exits Numeric control mode.

The F1 and F2 favorite buttons are programmed by a
press and hold. They save current input and volume level
settings for recall, and can be overwritten with another
press and hold.

1

2

3

4

4

3

2

1

Safety Instructions

1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be
retained for future reference.

3. Heed Warnings - All warnings on the appliance in the operating instruc­tions should be adhered to.

4. Follow Instructions - All operating and user instructions should be fol­lowed.

5. Water and Moisture - The appliance should not be used near water; for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.

6. Wall Mounting - The appliance should be mounted to a wall only as recom­mended by the manufacturer.

7. Ventilation - The appliance should be situated so that its location or posi­tion does not interfere with its proper ventilation. For example, the appli­ance should not be situated on a bed, sofa, rug, or similar surface that
may block the ventilation openings, or placed in a built-in installation, such
as a bookcase or cabinet that may impede the flow of air through the
ventilation openings.

8. Heat - The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers)
that produce heat.

9. Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.

10.Grounding or Polarization - Precaution should be taken so that the ground­ing or polarization means of an appliance is not defeated.

11.Object and Liquid Entry - Care should be taken so that objects do not fall
and liquids are not spilled into the enclosure through the openings.

12.Damage Requiring Service - The appliance should be serviced by quali­fied service personnel when:

A. Objects have fallen, liquid has been spilled into the appliance; or

B. The appliance has been exposed to rain; or

C. The appliance does not appear to operate normally; or

D. The appliance has been dropped or the enclosure is damaged.

13.Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should be
referred to qualified service personnel.

Precautions:

1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE FIRST
TIME, READ THE FOLLOWING SECTION CAREFULLY.

2. Do Not Touch The Unit With Wet Hands – Do not handle the unit when
your hands are wet or damp. If water or any other liquid enters the unit’s
cabinet, take it to a qualified service person for inspection.

3. Care – From time to time you should wipe off the front panel of the
cabinet with a soft cloth. Do not use rough material, thinners, alcohol or
other chemical solvents or cloths since this may damage the finish or
remove the panel lettering.

Double-gang Electrical Box

KPL Keypad

Trim Plate

KPSC Keypad

Keypad Installation

The KPSC connects to a KP6 or KPL keypad via a 12-pin connec­tor. A double-gang electrical box and faceplate is required for
installation.

1. Check whether or not you can route the wire to the location you
have chosen.

2. To install a double-gang keypad, you will need to use a UL/CSA
approved plastic two-gang (32 ci) electrical box.

3. Route CAT-5 wire to the electrical box from the CAA66 system
controller.

4. Use a 110 punchdown tool to connect each wire to its corre­sponding color labeled on the KP6/KPL punchdown terminal. Refer
to the KP6 or KPL keypad manual for complete instructions.

5. Insert the KPSC 12-pin connector into the 12-pin header on the
other keypad.

6. Mount the joined keypads in the electrical box and attach the
trim plate.

1

KPSC Side Panel

The KPSC 12-pin connector is located on the left side of the key­pad (when facing front). This is covered when a trim plate is
installed.

CONNECTOR - 12-pin connector for connecting to KP6 or
KPL keypad.

1

KPSC Front View

Source