Russell G200M22 User Manual

221 S. Berry St., P.O. Box 1030, Brea, CA 92822-1030 • Tel (714) 529-4461 • FAX (714) 529-8503 www.coldzone.com

1/2 to 3 HP

4 to 6 HP

MEA

UNI-PAK

Air Cooled Condensing Units 1/2 to 6 HP

Publication No. 502.12 rev. 2

March, 2007

HTPG, a division of Carrier Commercial Refrigeration

Description

Options

Horsepower 050 = 1/2 HP 075 = 3/4 HP 100 = 1 HP 101 = 1 HP 150 = 1-1/2 HP 151 = 1-1/2 HP 165 = 1-1/2 HP 200 = 2 HP 201 = 2 HP 202 = 2 HP

215 = 2 HP 250 = 2 HP 251 = 2HP 300 = 3 HP 301 = 3 HP 315 = 3 HP 400 = 4 HP 401 = 4 HP 500 = 5 HP 600 = 6 HP 650 = 6-1/2 HP

Indoor Models

• Hermetic, Semi-hermetic, Discus or Scroll compressor.

• Generously sized condenser, Copper tubes/Aluminum fins

• Large electrical control panel for power and control circuits

• Compressor contactor or start kit

• Encapsulated high and low pressure controls (adjustable low pressure control on low temp models)

• Refrigerant receiver with shutoff valve and relief plug

• All-weather housing

• UL and cUL listed for indoor or outdoor use

Outdoor Models

• Includes all Indoor model features - plus:

• Liquid line kit with filter/drier and sight glass with moisture indicator

• Suction line piping to exterior of cabinet

• Low Ambient - flooded head pressure control valve

• Crankcase heater

• Electric defrost timer with defrost contactor/relay on low

temperature models (ED10-230/1)

• Air Defrost Timer (2-1/2 through 6 HP High and Medium temp

models only, optional for other HP)

• Factory installed air defrost timer

• Factory installed electric defrost timer with contactor

• Low ambient flooded control (STD on Outdoor models)

• Mild ambient fan cycle control (for 2 fan units only)

• Wire fan guard(s) kit

• Suction line piping to exterior of cabinet (STD on Outdoor units)

• Suction line kit with filter and piping

• Liquid line (piping only)

• Liquid line kit with piping, filter/ drier and sight glass (STD on Outdoor models)

• Suction accumulator

• Oil separator (not available with mounted accumulator)

• Crankcase heater

• Copper fins, or coated condenser coil

• Tiered stacking

• Liquid line solenoid

• Fused disconnect

• High ambient oversized condenser coil - contact Applications

• Spring mounting for semi-hermetic compressors

ColdZone Uni-Pak condensing units are ideally suited for use

in a variety of commercial applications such as cafeterias,

convenience stores, restaurants and fast food outlets. Uni-Pak units offer a winning combination of quality, economy, and flexibility coupled with lower long term operating costs.

This low profile product line has been designed around environmentally safer refrigerants. All models utilize R-22 or R-404A. Units are available with a choice of compressors: low cost hermetic and scroll or heavy duty semi-hermetic and discus.

In addition to the basic Indoor and Outdoor models described in this bulletin, ColdZone can also provide pre-engineered system packages with matching evaporators and accessories.

These Uni-Pak condensing units are designed for operation in ambient air temperatures up to 110°F. Oversized condensers are available for most models. Contact our Applications Engineering department for requirements exceeding 110°F ambient temperature.

Features

Nomenclature

I R C S 050 H 22 — 2 T — 2

Refrigerant Type 22 = R-22 44= R-404A / 507 (Q) = Vintage Code

Temperature Range (varies by unit) H = High /Medium (0° to 55°S.T.) M = Medium (-10° to 45° S.T.) L = Low (-40° to 25° S.T.)

S = COLDSAVER

I = INDOOR

O = OUTDOOR

R = Remote P = Precharged W = Water Cooled

C = Center Mnt Evap E = End Mount Evap I = Inter-Temp

Blank = One Evap 2 = Two Evaps

Compressor Type D = Discus S = Semi-Hermetic H = Hermetic G = Scroll

T = 3 Phase S = 1 Phase

2 = 208/230V 4 = 460V

HTPG, a division of Carrier Commercial Refrigeration

DESCRIPTION IR*-H IR*-D IR*-S IR*-G OR*-H OR*-D OR*-S OR*-G

Hermetic STD N/A N/A N/A STD N/A N/A N/A

Discus N/A STD N/A N/A N/A STD N/A N/A

Semi-Hermetic N/A N/A STD N/A N/A N/A STD N/A

Scroll N/A N/A N/A STD N/A N/A N/A STD

Oil failure control (as required) N/R STD STD N/R N/R STD STD N/R

Encapsulated high and low pressur e controls**

Compressor contactor (1Ø or 3Ø), start kit (1Ø)

Control trans former (460v to 230V) as required

Copper tubes , Aluminum fins

Fan motor(s) - overload protection

Fan blade(s) - individually balanced

Fan guard(s)

Suction line ( vibrasorber† and piping only )

Suction kit (vibrasorber†, piping and suction filter)

Suction line accumulator

*Liquid line kit

Discharge vibras ober N/R STD†† STD†† N/R N/R STD†† STD†† N/R

Shut-off valve(s)

Fusible plug

Galvanized steel all weather housing

Control panel

Fan cycle control (2 Fan models only)

Flooded head pressure c ontrol

Air defrost time clock

Electric defrost package (1) (1) (1) (1)

UL and cUL listed

Leak and dielectric tested before shipping

Dry Nitrogen shipping charge (25 to 35 PSI)

OPTIONAL

STANDARD

OPTIONAL

STANDARD

OPTIONAL

STANDARD

PACKAGED UNITS

STANDARD UNITS

STANDARD

STD on 3-6 HP

STANDARD

OPTIONAL

STANDARD

OPTIONAL

STANDARD

OPTIONAL

STANDARD

UNI-PAK

Features and Options

COMPRESSOR

ELECTRICAL

CONTROLS

CONDENSER

PIPING

COMPONENTS

RECEIVER

HOUSING

LOW AMBIENT

CONTROLS

STD = Standard Feature N/R = Not Required N/A = Not Available OPT = Optional Feature

TESTING

DEFROST

PROVISIONS

† Vibrasorber not required for Hermetic and Scroll compressors.Vibrasorber not included for 1/2 through 2HP models, Add optional kit SPR-VB if suction vibrasorber required. ††Standard for 2-1/2 through 6HP Models. For 1/2 to 2HP models, add kit number SPR-VB to include vibrasorbers and compressor spring mounting. *Liquid line kit includes: piping, filter drier, sight glass/moisture indicator. ** Adjustable low pressure control on low temp models in lieu of fixed control. (1) Electric defrost kit is included on Low temperature models. ED-10-230/1 for 1/2 to 3 HP models, and ED11-230/3 for 4 to 6 HP models.

1/2 through 3 HP

4 through 6 HP

+ 5 hidden pages