Page 1
FORM NO. G11-498 REV. 3
Supersedes Form No. G11-498 Rev. 2
90TS- SERIES
Models with Input Rates
from 45,000 to 120,000 BTU/HR
[13.19 to 35.17 kW]
(All Models 90% A.F.U.E.† or Above)
90 HIGH EFFICIENCY
DOWNFLOW/
HORIZONTAL
GAS FURNACES
The Rheem Value Series 90 High Efficiency line of downflow/horizontal gas furnaces are designed for utility rooms,
closets, alcoves, attics or crawl spaces. The 90TS is
shipped in the downflow configuration and is easily converted for horizontal left-hand airflow applications.
The design is certified by CSA.
Features
■ Low profile “34 inch” design is lighter and easier to handle
and leaves room for optional accessories.
■ Top electrical connections, left or right gas and conden-
sate drainage connections on downflow models.
■ Condensate drain for horizontal application provided
standard.
■ Integrated control board manages all operational functions
and provides hookups for an electronic air cleaner.
■ A slow-opening gas valve and a specially designed
inducer system make it one of the quietest furnaces on
the market today.
■ Galvanized steel cabinet.
■ Optional indoor or outdoor combustion air.
■ Control board diagnostics.
A variety of cooling coils and plenums designed to use with
the Rheem Value Series 90 gas furnaces are available as
optional accessories for air conditioning models.
✝A.F.U.E. (Annual Fuel Utilization Efficiency) calculated in accordance with Department
of Energy test procedures.
Page 2
2 Rheem Heating, Cooling and Water Heating
STANDARD EQUIPMENT
Completely assembled and wired; heat exchanger; primary: 409 stainless steel,
secondary: 29-4C stainless steel; induced draft; pressure switch; redundant
main gas control; blower compartment door safety switch; solid state time
on/off blower control; limit controls; manual shut-off valve; 100% safety lock
out; cool fan off delay; field selectable heat fan off delay; one hour automatic
retry; self-test diagnostics; control diagnostics; electronic air cleaner
connections; pressure regulator for natural and L.P. (propane) gases;
transformer; direct drive, multi-speed blower motor.
(Please note: a thermostat is not included as standard equipment.)
OPTIONAL EQUIPMENT
(See Accessory Page)
All models can be converted by a qualified distributor or local service dealer to
use L.P. (propane) gas without changing burners. Factory approved kits must be
used to convert from natural to L.P. (propane) gas and may be ordered as
optional accessories from a parts distributor.
For L.P. (propane) operation, refer to Conversion Kit Index Form.
WARNING
THIS FURNACE IS NOT APPROVED
OR RECOMMENDED
FOR USE IN MOBILE HOMES
PRIMARY AND SECONDARY
HEAT EXCHANGER
REMOTE
SENSOR
DIRECT SPARK IGNITION &
REMOTE SENSOR
IN-SHOT BURNERS
PRESSURE SWITCH
DRAFT INDUCER
INTEGRATED
FURNACE
CONTROL
GAS VALVE AND
MANIFOLD
90 HIGH EFFICIENCY
DOWNFLOW/HORIZONTAL
GAS FURNACE
Page 3
Rheem Heating, Cooling and Water Heating 3
MODEL IDENTIFICATION
[ ] Designates Metric Conversions
BEFORE PURCHASING THIS APPLIANCE, READ IMPORTANT ENERGY COST AND EFFICIENCY INFORMATION AVAILABLE
FROM YOUR RETAILER.
PHYSICAL DATA AND SPECIFICATIONS
DOWNFLOW/HORIZONTAL MODELS
U.S. and Canadian Models
NOTES: All models are 115V, 60HZ, 1
ø.
Gas connection size for all models is
1
/2
" [13 mm] N.P.T.
➀ See Conversion Kit Index Form for high altitude derate.
➁ Canadian installations only.
➂ In accordance with D.O.E. test procedures.
MODEL NUMBERS
90TS- SERIES
INPUT-BTU/HR [kW] ➀
HEATING CAPACITY
BTU/HR [kW]
HIGH ALTITUDE INPUT
[kW] ➁
HIGH ALTITUDE OUTPUT
CAPACITY [kW] ➁
BLOWER (D x W)
[mm]
MOTOR H.P. [W]
SPEEDS-TYPE
MOTOR FULL LOAD AMPS 6.8 6.8 6.8 9.5 8.0 9.5
HEATING SPEED Med-Low Low Med Low Med Low
COOLING SPEED High High High High High High
HEAT EXT. STATIC PRESSURE
(IN. W.C.) [kPA]
RATED EXT. STATIC PRESSURE
(IN. W.C.) [kPA]
HEATING C.F.M. @ .2"
W.C. E.S.P. [L/s]
COOLING C.F.M. @ .5"
W.C. E.S.P. [L/s]
TEMPERATURE RISE
RANGE °F [°C]
STANDARD FILTER [mm]
APPROX. SHIPPING WEIGHT
(LBS.) [kG]
AFUE ➂
CALIFORNIA SEASONAL
EFFICIENCY ➂
04EES** 06EES** 07EES** 07EFS** 09EJS** 10EGS**
45,000
[13.19]
42,000
[12.31]
40,500
[11.87]
37,800
[11.07]
11 x 7
[279 x 178]
1/2 [373]
4-PSC
.10 [.025] .12 [.029] .12 [.029] .12 [.029] .15 [.037] .20 [.049]
.50 [.12] .50 [.12] .50 [.12] .50 [.12] .50 [.12] .50 [.12]
890 [420] 885 [418] 1060 [500] 1275 [602] 1400 [661] 1425 [673]
1220 [576] 1180 [557] 1150 [543] 1625 [767] 1570 [740] 1820 [859]
30-60
[16.7-33.3]
(2) 12" x 20"
[305 x 508]
111 [50.3] 117 [53.1] 123 [55.8] 123 [55.8] 148 [67.1] 152 [68.9]
92.0% 92.4% 92.0% 92.3% 92.4% 92.0%
84.35% 86.46% 89.96% 85.00% 86.40% 87.02%86.40%
60,000
[17.58]
56,000
[16.41]
54,000
[15.83]
50,400
[14.77]
11 x 7
[279 x 178]
1/2 [373]
3-PSC
40-70
[22.2-38.9]
(2) 12" x 20"
[305 x 508]
75,000
[21.98]
70,000
[20.51]
67,500
[19.78]
63,000
[18.46]
11 x 7
[279 x 178]
1/2 [373]
3-PSC
45-75
[25-41.7]
(2) 12" x 20"
[305 x 508]
75,000
[21.98]
70,000
[20.51]
67,500
[19.78]
63,000
[18.46]
12 x 7
(2) 12" x 20"
[305 x 178]
3/4 [559]
3-PSC
35-65
[19.4-36.1]
[305 x 508]
[305 x 279]
[19.4-36.1]
(2) 12" x 20"
[305 x 508]
90,000
[26.37]
84,000
[24.61]
81,000
[23.73]
76,000
[22.27]
12 x 11
1/2 [373]
3-PSC
35-65
09EGS**
90,000
[26.37]
84,000
[24.61]
81,000
[23.73]
76,000
[22.27]
12 x 11
[305 x 279]
3/4 [559]
3-PSC
9.5
Low
High
.15 [.037]
.50 [.12]
1400 [661]
1850 [873]
35-65
[19.4-36.1]
(2) 12" x 20"
[305 x 508]
148 [67.1]
92.4%
105,000
[30.77]
97,000
[28.43]
94,500
[27.70]
87,500
[25.64]
12 x 11
[305 x 279]
3/4 [559]
3-PSC
50-80
[27.8-44.4]
(2) 12" x 20"
[305 x 508]
12EHS**
120,000
[35.17]
113,000
[33.12]
108,000
[31.65]
100,000
[29.31]
11 x 10
[279 x 254]
3/4 [559]
3-PSC
9.5
Low
High
.20 [.049]
.50 [.12]
1565 [739]
2040 [963]
50-80
[27.8-44.4]
(2) 14" x 20"
[609 x 508]
160 [72.6]
92.1%
87.37%
Efficiency
T = Downflow/
Horizontal
Condensing
S = 3rd Design Series
Heating Input DesignationDesign Series
Electric Ignition
04E
06E
07E
09E
10E
12E
Input BTU/HR [kW]
45,000 [13.1]
60,000 [17.6]
75,000 [21.9]
90,000 [26.4]
105,000 [30.7]
120,000 [35.2]
Blower Designation [mm]
E = Standard Cabinet
11 x 7 [279 x 178]
1
/2 H.P. PSC
Fuel Designation
S = Natural Gas - CSA United States & Canada
(North American)
Value Series
F = Wide Cabinet
12 x 7 [305 x 178]
3
/4 H.P. PSC
G = Standard Cabinet
12 x 11 [305 x 279]
3
/4 H.P. PSC
H = Standard Cabinet
11 x 10 [279 x 254]
3
/4 H.P. PSC
J = Standard Cabinet
12 x 11 [305 x 279]
1
/2 H.P. PSC
01SE04EST90
Rheem
Page 4
4 Rheem Heating, Cooling and Water Heating
DOWNFLOW MODELS
[ ] Designates Metric Conversions
IMPORTANT NOTE: Horizontal furnace maybe installed for horizontal left hand air supply ONLY. The condensate trap provided for horizontal application must be
installed in the field beneath the unit as directed in the furnace Installation & Operating Instructions.
MODEL
90TS-
04 171/2 [445] 1611/32 [415] 155/8 [397] 2 [51] 165/8 [422] 137/8 [352] 0 0 0 1 [25] 2 [51] 0 111 [50]
06 171/2 [445] 1611/32 [415] 155/8 [397] 2 [51] 165/8 [422] 137/8 [352] 0 0 0 1 [25] 2 [51] 0 117 [53]
07EE 171/2 [445] 1611/32 [415] 155/8 [397] 2 [51] 165/8 [422] 137/8 [352] 0 0 0 1 [25] 2 [51] 0 123 [56]
07EF 21 [533] 1927/32 [504] 193/16 [486] 2 [51] 201/8 [511] 173/8 [441] 0 0 0 1 [25] 2 [51] 0 123 [56]
09
10 21 [533] 1927/32 [504] 193/16 [486] 2 [51] 201/8 [511] 173/8 [441] 0 0 0 1 [25] 2 [51] 0 152 [69]
12
A B C D E F
21 [533] 1927/32 [504] 193/16 [486]
241/2 [622] 2311/32 [593] 225/8 [575]
2 [51]
2 [51]
201/8 [511] 173/8 [441]
235/8 [600] 207/8 [530]
LEFT
SIDE
0 0 0 1 [25] 2 [51] 0 148 [67]
0 0 0 1 [25] 2 [51] 0 160 [73]
MINIMUM CLEARANCE (IN.) [mm]
RIGHT
BACK TOP FRONT VENT
SIDE
SHIP
WGTS.
[kg]
Page 5
Rheem Heating, Cooling and Water Heating 5
HORIZONTAL MODELS
IMPORTANT NOTE: Horizontal furnace may be installed for horizontal left hand air supply ONLY. The condensate trap provided for horizontal application must be
installed in the field beneath the unit as directed in the furnace Installation & Operating Instructions.
[ ] Designates Metric Conversions
Page 6
6 Rheem Heating, Cooling and Water Heating
BLOWER PERFORMANCE DATA—90TS MODELS
NOTE: Recommended blower speeds are in bold.
[ ] Designates Metric Conversions
GENERAL TERMS OF LIMITED WARRANTY
Rheem will furnish a replacement for any part of this product
which fails in normal use and service within the applicable
period stated, in accordance with the terms of the limited
warranty.
For Complete Details of the Limited Warranty, Including Applicable Terms
and Conditions, See Your Local Installer or Contact the Manufacturer for
a Copy.
Primary and Secondary Heat Exchanger ...Twenty (20) Years
*Any Other Part.............................................Five (5) Years
*This five year limited warranty is applicable only to single-phase products
installed in residential applications on or after January 1, 2001.
MODEL
90TS-
04EES**
06EES**
07EES**
07EFS**
09EJS**
09EGS**
10EGS**
12EHS**
BLOWER
SIZE
IN. [mm]
11 x 7
[279 x 178]
11 x 7
[279 x 178]
11 x 7
[279 x 178]
12 x 7
[305 x 178]
12 x 11
[305 x 279]
12 x 11
[305 x 279]
12 x 11
[305 x 279]
11 x 10
[279 x 245]
MOTOR
H.P.
[W]
1/2
[373]
1/2
[373]
1/2
[373]
3/4
[559]
1/2
[373]
3/4
[559]
3/4
[559]
3/4
[559]
BLOWER
SPEED
LOW
MED-LO
MED-HI
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
LOW
MED
HIGH
EXTERNAL STATIC PRESSURE INCHES WATER COLUMN [kPa]
0.1 [.02] 0.2 [.05] 0.3 [.07] 0.4 [.10] 0.5 [.12] 0.6 [.15] 0.7 [.17]
820 [387]
930 [439]
1150 [543]
1414 [667]
910 [429]
1115 [526]
1365 [644]
890 [420]
1100 [519]
1340 [632]
1405 [668]
1595 [753]
1835 [866]
1155 [545]
1420 [670]
1605 [757]
1420 [670]
1605 [757]
2005 [946]
1460 [689]
1680 [793]
2055 [970]
1590 [750]
1840 [868]
2315 [1093]
790 [373]
890 [420]
1120 [528]
1365 [644]
885 [418]
1080 [510]
1315 [620]
860 [406]
1060 [500]
1295 [611]
1375 [649]
1560 [736]
1780 [840]
1125 [531]
1400 [661]
1575 [743]
1400 [661]
1575 [743]
1965 [927]
1425 [672]
1645 [776]
2000 [944]
1565 [738]
1820 [860]
2250 [1062]
760 [359]
850 [401]
1090 [514]
1320 [622]
860 [406]
1045 [493]
1270 [600]
835 [394]
1025 [484]
1250 [590]
1350 [637]
1525 [720]
1730 [816]
1100 [519]
1380 [651]
1550 [732]
1380 [651]
1550 [732]
1930 [910]
1390 [656]
1615 [762]
1940 [915]
1540 [727]
1800 [850]
2185 [1031]
CFM [L/s] AIR DELIVERY
725 [342]
815 [384]
1045 [493]
1270 [599]
815 [384]
1005 [474]
1225 [578]
790 [373]
980 [462]
1200 [566]
1310 [618]
1480 [698]
1675 [791]
1080 [510]
1365 [644]
1560 [736]
1365 [644]
1560 [736]
1890 [892]
1375 [649]
1585 [748]
1880 [887]
1505 [710]
1750 [826]
2110 [996]
690 [326]
785 [370]
1002 [473]
1220 [576]
770 [363]
965 [455]
1180 [557]
750 [354]
940 [443]
1150 [543]
1270 [599]
1440 [679]
1625 [767]
1060 [500]
1350 [637]
1570 [740]
1350 [637]
1570 [740]
1850 [873]
1360 [642]
1560 [736]
1820 [859]
1475 [696]
1700 [802]
2040 [963]
650 [306]
750 [354]
950 [448]
1165 [550]
725 [342]
920 [434]
1125 [491]
705 [332]
890 [420]
1090 [514]
1235 [583]
1380 [651]
1555 [734]
1000 [472]
1260 [594]
1480 [698]
1260 [594]
1480 [698]
1765 [833]
1280 [604]
1490 [703]
1745 [823]
1425 [672]
1645 [776]
1965 [927]
610 [288]
720 [340]
900 [425]
1115 [526]
680 [321]
875 [413]
1070 [505]
660 [311]
845 [399]
1025 [484]
1195 [564]
1325 [625]
1480 [698]
940 [443]
1175 [554]
1395 [656]
1175 [554]
1395 [656]
1680 [793]
1200 [566]
1420 [670]
1675 [790]
1375 [649]
1590 [750]
1890 [892]
Page 7
Rheem Heating, Cooling and Water Heating 7
ACCESSORIES—DOWNFLOW
PLENUM DATA FOR “A” COILS
Plenum adapters are required in some applications when plenum and
furnace size do not match.
VENT TERMINATION KITS CONCENTRIC: HORIZONAL/
VERTICAL =
RXGY-E03A (US & Canadian Installations)
HORIZONTAL TWO PIPE: RXGY-D02, RXGY-D03, RXGY-D04
(US Installations)
RXGY-D02A, RXGY-D03A, RXGY-D04A (Canadian Installations)
RXGY-G02 (US Only)
CONDENSATE PUMP KIT: RXGY-B01
NEUTRALIZER KIT: RXGY-A01
FOSSIL FUEL KIT: RXPF-F01, RXPF-F02 (TVA)
FOR HIGH ALTITUDES:
*Filter racks are shipped without filters.
RXGP-F03
TWINNING KIT—is for use with Rheem Value Series Gas Furnaces for
parallel operation requirements.
COMBUSTIBLE FLOOR BASE: RXGC-B17, RXGC-B21, RXGC-B24
EXTERNAL TOP MOUNT FILTER RACK: RXGF-CC
INTERNAL FILTER RACK FOR AIR RETURN DUCT: RXGF-DB*
Each order contains (1) one box of 10 filter racks supplied without filters.
*Filters available through PROSTOCK
®
.
FURNACE
WIDTH
IN. [mm]
PLENUM
WIDTH
IN. [mm]
PLENUM ADAPTER
DOWNFLOW
COIL
PLENUM
171/2 [445] 161/4 [413] RXAA-C186 RXAL-B16BU
171/2 [445] 201/4 [514]
RXAA-C173 RXAL-B20BU
171/2 [445] 215/8 [549] RXAA-C187 RXAL-B21BU
171/2 [445] 251/4 [641] RXAA-C174 RXAL-B25BU
211/2 [533] 251/4 [641]
RXAA-C175 RXAL-B25BU
211/2 [533] 221/4 [565] RXAA-C176 RXAL-B22BU
241/2 [622] 251/4 [641]
RXAA-C177 RXAL-B25BU
241/2 [622] 215/8 [549] RXAA-C187 RXAL-B21BU
211/2 [533] 215/8 [549]
RXAA-C188 RXAL-B21BU
*For installations over 5000 ft.
OPTION CODE FOR HIGH ALTITUDE: U.S. & Canada – 278
NOTE: High altitude kits and options do NOT include additional burner
orifices. If a burner orifice change is necessary, they must be
ordered through PROSTOCK
®
. See Installation Instructions for
more information.
Option – 278 furnaces are shipped with #51 DMS orifices installed. This is
one drill size smaller than standard furnaces to account for expected
average elevations and heating values typically seen in these areas.
CAUTION: Always follow National Fuel Gas Code (NFGC) guidelines when
converting furnaces for high altitudes.
For all installations above 2000 ft. (including all option – 278 models), the
burner orifice size needs to be recalculated and verified. A burner orifice
change may still be required. See Installation Instructions for more
information.
NOTE: For Canadian installations only, an optional derate (manifold gas
pressure reduction) method may be used to adjust the furnace for
altitude. See Installation Instructions for more information. This
optional method may NOT be used for U.S. installations.
[ ] Designates Metric Conversions
THERMOSTATS
*HIGH ALTITUDE KIT:
F04-105 KBTU/H
F06-45/60/90 KBTU/H
F05-120 KBTU/H
F07-75 KBTU/H
FILTER RACK FILTER SIZES®INCHES [mm]
MODEL 90TS- RXGF-CC
04 (2) 12 x 20 [305 x 508]
06 (2) 12 x 20 [305 x 508]
07 (2) 12 x 20 [305 x 508]
09 (2) 12 x 20 [305 x 508]
10 (2) 12 x 20 [305 x 508]
12 (2) 14 x 20 [305 x 508]
Page 8
Before proceeding with installation, refer
to installation instructions packaged
with each model, as well as complying
with all Federal, State, Provincial, and
Local codes, regulations, and practices.
Rheem Heating,
Cooling and
Water Heating
P.O. Box 17010, Fort Smith, AR 72917
“In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.”
PRINTED IN U.S.A. 12-08 DC FORM NO. G11-498 REV. 3
Supersedes Form No. G11-498 Rev. 2
Loading...