RPI Industries SCAS36R-DI-I Service Manual

RPI Industries, Inc.

AIR SCREEN and SELF-SERVE

OPERATION AND SERVICE MANUAL

WARRANTY INFORMATION

For Models

Olympus Drop-In

SCAS36R-DI-I
SCAS48R-DI-I
SCAS60R-DI-I

SCAS72R-DI-I
SCAS36R-DI-II
SCAS48R-DI-II
SCAS60R-DI-II
SCAS72R-DI-II

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

220 Route 70, Medford, NJ 08055

Phone: [phone] Fax: [phone]

IMPORTANT: THE FOLLOWING INFORMATION SHOULD BE RETAINED FOR

FUTURE REFERENCE

RPI Industries, Inc.

Congratulations, you have just purchased the finest air screen/self-serve display case
available. RPI Industries, Inc. development of an exclusive humidity and temperature
control system insures product shelf life and enticing displays, which leads to a better
bottom line. We at RPI Industries, Inc. hope you are satisfied with your case for many
years to come.

IMPORTANT IMPORTANT IMPORTANT

Controls are pre-set at our factory. Please consult our refrigeration service department
at [phone] if setting changes are required.

ADJUSTING CONTROLS WITHOUT PRIOR AUTHORIZATION FROM

RPI INDUSTRIES MAY VOID YOUR WARRANTY

Please consult your operation and service manual for proper care of your case.

For Your Records Enter Model And Serial Number of the Product You Purchased.

Model:____________________________

Serial No.:________________________________

CASES ARE DESIGNED TO OPERATE IN AN ENVIRONMENT OF 75 DEGREES

FAHRENHEIT AMBIENT AND 55% HUMIDITY.

2

RPI Industries, Inc.

REFRIGERATED AIR SCREENS and SELF SERVE CASES

USE & SERVICE MANUAL

1. Temperature of case is controlled by temperature control in storage area. Cases

are pre-set at factory. Settings should not be touched, without first notifying the
factory.

2. Condensing unit is COPELAND 115/60 or 208/230V/60 cycle/single phase air-

cooled or equal.

3. Refrigerant: R134A, R22, R404

4. Average case temperature in Air Screens and Self-Serve cases is between 37 and

41 degrees Fahrenheit.

5. Make certain that the drain pan on refrigerated cases is checked weekly. Calcium

deposits may accrue depending on area and water quality. The float on the drain
pan should be cleaned weekly for proper operation.

6. Brush out or vacuum condenser (looks like a black radiator) once a month for

efficient operation. (When the condenser is clogged with dirt and dust, the case
looses its efficiency, causing the unit to operate without stopping).

7. Do not store packages against blower (evaporator coils) so airflow is not impeded.

8. Do not block airflow inside display area over front and back grill.

9. Keep the flow area around the fixture clean and orderly.

10. Tracks and sliding door fixtures should be cleaned and lubricated periodically.

11. Check inside cooling coil housing to be certain that it is free of ice debris.

12. Replace any malfunctioning parts as soon as possible.

13. It is most important that the interior of the fixture be cleaned periodically. HOW

TO CLEAN: Remove the product load and all shelving. Use only mild soap or
detergent to wash the interior panels. Rinse with clean, warm water, and dry with
a soft absorbent cloth.

14. Failure to comply with above may void warranty.

3

RPI Industries, Inc.

RECEIVING & INSPECTION PROCEDURE

1. All fixtures have been carefully operation tested and inspected before shipping and

are determined to be in good operating condition before leaving our factory. All
units have been run for 24 hours prior to shipment to ensure proper operation.

2. Upon arrival of the fixture the cases should be examined thoroughly for any

damage. If any damage is discovered, it should be noted on the delivery ticket or
Bill of Lading and signed to that effect.

3. If you find any hidden damage, notify the carrier at once. Confirm all claims in

writing. RPI Industries, Inc. cannot assume responsibility for filing freight claims,
however, the factory will assist if required.

LOCATING THE FIXTURE

1. Locate refrigerator or freezer in a dry, cool and well-ventilated area. When

possible, do not locate any fixture in the direct rays of the sun, near heating
ducts, radiators, stoves, doors or any device which will hinder the airflow as
designed.

2. There must be at least 24 inches of unobstructed clearance from the condensing

unit compartment.

3. Locate the electrical outlet in such a manner that you may plug in the service cord

(when furnished) direct, without the use of an extension cord, must be 115V/20A
or 115/208-230V 20/30-amp circuit (depending upon size of case model). On
models not furnished with a service cord, a permanent electrical connection is
required. Make sure that no other electrically operated appliances are connected
to the circuit operating this fixture, which will cause an overload. Overloaded
circuits are extremely hazardous. THE VOLTAGE MUST BE MAINTAINED TO

WITHIN 5% OF VOLTAGE INDICATED ON THE NAMEPLATE FOR PROPER
OPERATION.

4. This unit is intended to be sealed to the floor with a NSF approved sealant. Unless

supplied with castors or legs, In addition, Air screen display cases may be installed
flush against the rear wall with no clearances.

5. This unit is for use in a max. 75F (24C) room ambient

will effect the operation and warranty of this unit.

.

Higher room temperature

4