Royal Sovereign NB-1900N User Manual
OWNER'S MANUAL
LAMINATOR Model No.
For any customer support needs, please choose
the « Customer Support » tab on www.royalsovereign.com.
NB-1900N
Read all instructions carefully before use.
Royal Sovereign International Inc.
NB-1900N
TABLE OF CONTENTS
TOPIC PAGE
INTRODUCTION
MAJOR PARTS
CHARACTERISTICS OF NB-1900N
SAFETY PRECAUTIONS
SET UP
CONTROL PANEL SETTINGS
HOT LAMINATING
COLD LAMINATING
COLOR FOIL LAMINATING
MOUNTING BOARD LAMINATING
CLEAN ROLLERS AND REMOVE JAMMED FILMS
IMPORTANT SAFETY CONCERNS
MAINTENANCE
ASSEMBLY PARTS
TROUBLESHOOTING
SPECIFICATIONS
3
3
3
4
5
5
7
8
9
10
11
12
12
12
12
13
NB-1900N
INTRODUCTION
Thank you for purchasing a Royal Sovereign Laminator.
To insure high quality lamination, please read this instroduction manual thoroughly.
For additional product support or factory-direct ordering information.
Call Royal Sovereign Customer Service at (800) 397-1025.
MAJOR PARTS
Top Cabinet
Output Power Cord
Control Button PanelInput LED
CHARACTERISTICS
LAMINATOR NB-1900N is an advanced laminator of contemporary design,
utilizing the lastest in laminating technology.
1. Contemporary design and rounded shape will enhance any decor.
2. A microprocessor is used for added protection.
1) The microprocessor protects the rollers
a.Even when power is off, rollers continue to turn until properly cooled down.
b.In the event of a power failure, rollers continue turning until properly cooled down.
2) The microprocessor prevents overheating
If a temperature sensor fails, the microprocessor prevents rollers from overheating.
3. Designed to prevent heat from radiating through the housing, using powerful fans.
4. Eight function settings, allow you to laminate various types of film.
5. Every time a button is pressed, a buzzor sounds.
6. Temperature is controled automatically for energy efficiency.
3
SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could
result in serious injury. Keep this information for future reference.
1.To prevent the possibility of fire or injury, do not allow articles
of clothing (neckties, scarves, or paperclips etc.) inside the
machine.
2. Do not attempt to laminate items that exceed total
recommended material thickness.
3.To prevent the possibility of electric shock, do not immerse
the laminator in water or permit liquids inside the machine.
4. Do not operate machine for any other purpose other than its
intended use.And do not insert sharp objects into front or rear
machine openings.
NB-1900N
5. This machine is for indoor use only.
6. Do not operate the machine if the outlet or power cord is
damaged. And do not alter the electric plug in any way.
Contact a qualified electrician.
7.The electrical outlet should be installed near the equipment
and should be easily accessible.
4
NB-1900N
SET UP
Place laminator on a sturdy, flat work surface. Allow ample clearence
behind laminator for laminated document or photograph to exit completely
without bending.
Connect laminator to an electrical outlet that matches laminator's rated voltage
and power requirements.
If an extension cord is required, use a cord rated higher than the laminator's
capacity.
CONTROL PANEL SETTINGS
Eight Functions allow you to laminate as necessary.
TACT-BUTTON and LED were designed for your convenience.
1.FUNCTION OF BUTTONS
TEMP
COLD
ON/OFF
2.DISPLAY
NB-1900N
Foil
~
200
~
150 180
~
80 125
Mic
COLD
: Increase setting
: Decrease setting
COLD
ON/OFF
B
7
6
5
4
3
2
1
: COLD Function
: Power On/off
200~250 micron (8~10 mil) film, color foil and
mount board laminating
150~180 micron (6~7 mil) film laminating
80~125 micron (3~5 mil) film laminating
Cold film laminating
5
Loading...