Royal Sovereign HSH-1201 Owner's Manual

LAMINATOR MODEL NO.HSH-1201

OWNER'S

MANUAL

S
t

a
n

d

by

H
ot

/
C

ol

d

P
O

W

E
R

Read all instructions carefully before use.

Royal Sovereign International Inc.

INTRODUCTION 3

MAJOR PARTS 3

SAFETY PRECAUTIONS 4

CONTROL PANEL INSTRUCTIONS 5

HOT LAMINATING PROCEDURE 8

COLD LAMINATING PROCEDURE 9

COLOR FOIL LAMINATING PROCEDURE 9

MAINTENANCE 10

TROUBLESHOOTING 11

SPECIFICATIONS 11

WARRANTY

TABLE OF CONTENTS

HSH-1201

TOPIC PAGE

INTRODUCTION

MAJOR PARTS

HSH-1201

Thank you for purchasing a Royal Sovereign HSH-1201 Laminating Machine.
It has been designed and manufactured to provide years of continuous service.
To insure high quality lamination, please read this instruction manual thoroughly.
This manual will provide you with complete operating and maintenance information.
For additional product support, call Royal Sovereign Customer Service
at [phone]/201-050-1020

Cover Roller Screw Cover Roller Power Cord

Front Opening

Cover

Control Panel LCD Panel

3

HSH-1201

SAFETY PRECAUTIONS

The safety recommendations outlined in this section are to be read,
understood and followed before operating the machine. Failure to
comply with any of the following safety procedures could result in
serious injury. Keep this information for future reference.

1.To prevent the possibility of fire or injury, do not allow articles
of clothing (neckties, scarves, or paperclips etc.) inside the
machine.

2. Do not attempt to laminate items that exceed total

recommended material thickness.

3.To prevent the possibility of electric shock, do not immerse the
laminator in water or permit liquids inside the machine.

4.Because the laminator creats heat,keep out of reach of
children.

5. Do not operate machine for any other purpose other than its

intended use.

6. This machine is for indoor use only.

7. Do not operate the machine if the outlet or power cord is

damaged. Contact a qualified electrician.

4

HSH-1201

CONTROL PANEL INSTRUCTIONS

5

Appropriate speed and temperature may be set, using the LCD controller.

CONTROL PANEL SETTINGS

LCD DISPLAY

BUTTONS

HSH-1201

6

LCD DISPLAY

CONTROL PANEL
FUNCTIONS

FILM

This displays the current film thickness.
10 film settings
3 mil=75 mic, 4 mil=100 mic, 5 mil=125 mic
6mil=150mic,7 mil=175 mic, 8mil=200mic,
10mil=250mic,

SPEED

12 speed options (1-12)

TEMPERATURE

This displays the current
temperature.
displayed when desired
temperature is met.

This Indicates that the current
temperature is either higher or

lower than the preset
temperature.Wait until the indicator stops
blinking.

Indicates what direction the

rollers are moving in

(FWD/REV).

Indicates if the machine is ON or

OFF.

T-Check

Press this to check the current temperature

Hot / Cold

Press this to choose the Hot/Cold function

Temp.

Press this to increase the temperature

Temp.

Press this to decrease the temperature

Speed 

Press this to increase the speed

Speed 

Press this to decrease the speed

Stand by

Set temperature 176°F(80°C) speed 2

Set

Press this to scroll through preset settings

Reverse

Reverse function

Power

Power ON/OFF

1. Place and use the laminator on a sturdy, flat work surface.

2. Plug in the laminator after verifying the correct outlet voltage.

3. Press the power button.

4. Make sure the machine is in the HOT lamination mode by pressing the

HOT/COLD button.

5. Select the correct pouch thickness by pressing the button.

6. Set the temperature and speed according to the pouch thickness. Please

refer to the SPECIFICATIONS section for recommended settings

7. The symbol will appear and you will hear 3 beeps when your

desired temperature is met. The machine is now ready for lamination.

8. Place the item to be laminated into the laminating pouch.

9. Insert the pouch (sealed side first) into the front opening of the machine.

10. The laminated item will exit out the rear of the machine when completed.

11. If you laminate several items continuously the may disappear,

please wait until it is displayed again before continuing lamination.

12. When the machine is on for an extended period of time, use a slightly

lower temperature setting as the internal temperature of the machine may

actually be higher than the preset temperature, which may cause the

document to bend

13. When you are finished laminating, press the OFF button. The rollers will

continue to roll until the temperature decreases to 140°F(60°C).

NOTE: Your laminated item will be hot and can easily bend. To keep your

laminated item flat, place on a flat surface and allow to cool.

HSH-1201

8

HOT LAMINATING PROCEDURE

HSH-1201

9

COLD LAMINATING PROCEDURE

COLOR FOIL LAMINATING PROCEDURE

1. Set the laminator in the COLD lamination mode by pressing the HOT/COLD

button.

2. The symbol will appear and you will hear 3 beeps when the machine is

in the cold temperature mode. The machine is now ready for lamination.

3. Place the document to be laminated on the adhesive side of the cold film with the

document face down.

4. Insert the document to be laminated into the front opening of the machine.

Remove the paper liner from the cold film slowly while the document is being
inserted into the machine.

NOTE: When switching the machine from the hot to cold mode, please wait until
the rollers cool down. It will take approximately 20-30 minutes. The symbol
will appear and you will hear 3 beeps.

IMPORTANT: Carrier is required for Foil Lamination

1. Set the temperature and speed according to the pouch thickness (FOIL).

Please refer to the SPECIFICATIONS section for recommended settings.

2. The READY ( ) symbol will stop blinking and a symbol will appear

when the correct temperature is met. The machine is now ready for lamination.

3. Position the color foil on the document with the color side facing up. When you

are applying the foil to small areas or using different colors, use the tape that’s
included to hold the foil in place.

4. Place the document into the paper carrier.

5. Insert the carrier into the front opening of the machine.

6. The carrier will exit out the rear of the machine when completed.

NOTE: Your laminated item will be hot and can easily bend. To keep your
laminated item flat, place on a flat surface and allow to cool.

HSH-1201

10

MAINTENANCE

When adhesives from film build up on the rollers, the quality of lamination will
decrease and jamming may occur. Please clean the rollers regularly.

1. Turn on the laminator and set the
temperature to 212°F(100°C) and set
the mil thickness to 4mil(100mic).

2. Insert a sheet of clean thick paper (about

0.5mm to 1/50" thick) into the front
opening of the machine 2-3 times to
remove excess adhesives from the rollers.

3. To thoroughly clean the rollers make sure
the machine is in the COLD mode and the
rollers are completely cool.

4. Unscrew the 2 screws on the cover using
a screwdriver. Once the screws are off,
remove the top cover.

5. Use a cleaning solvent such as Laminex
Poly-off or something equivalent on a lint
free cloth to clean residue on the rollers.
(Do not use alcohol or petroleum based
cleaning solvents or abrasives).

6. Place the cover and screws back into place and tighten.

7. Use and store this unit in a dry area, damp area may damage the machine.

HSH-1201

11

TROUBLESHOOTING

Problem Possible Cause Possible Solution

SPECIFICATIONS

Model HSH-1201

Dimensions 22.8"x11.4"x4.9" (in) 580x290x124 (mm)
Max.Laminating Width 13 (in) 330 (mm)
Max.Lam. Thickness 1/10" (in) 3mm
Film Thickness 1.5-10 (mil) 37.5 ~ 250mic
Heat method Hot Roller
Warm up time 5‘30” min
Cooling system DC FAN
Motor Type DC GEARED MOTOR
Laminating speed 8.86 (ft/min) 2700 (mm/min)
Number of rollers 6
Unit weight 32 (lbs) 14.5Kg
Voltage supply 100V/120V/220~240V(50~60Hz)
Power Consumption 1200W/1200W/1200~1300 W

Motor doesn’t work

- Power cord may not be
plugged in.

- Power switch is off

- Check and plug in the
power cord.

- Check and turn on the
power.

Pouches are not

laminating correctly

- If laminating heat sealed
pouches, the machine
may be set in the COLD
mode.

- The temperature may be
set too low

- The speed is set too high

- Make sure the machine
is in the HOT mode

- Check the temperature
is set according to
pouch thickness.

- Adjust to a lower speed.

HSH-1201

12

POUCH FILM SETTINGS

Please refer to the settings below if you are laminating a few items.

Please refer to the settings below if you are laminating a few items.

This warranty applies to repair or replacement of product found to be defective
in material or workmanship for one year from the date of the original purchase. This
warranty is extended only to the original purchaser.

This warranty does not apply to damage resulting from abuse, misuse or
improper maintenance or damage that is attributable to acts of God. Royal
Sovereign International, Inc. (and its affiliated companies) is not liable for incidental
or consequential damages of any nature. This limitation would not apply if you live
in those areas that do not permit the exclusion or limitation of incidental or
consequential damages.

Royal Sovereign International will repair or replace this product if it is found to
be defective in material or workmanship. Defective product must be returned to
Royal Sovereign International, freight prepaid, with proof of purchase and Return
Shipping & Handling payment (check or money order). Upon repair or replacement
the product will be returned to the customer.

Return defective product to the following address with a detailed description
of the problem. If possible, pack in original carton. Pleaseprepay shipping
charges.

LIMITED ONE YEAR WARRANTY

Model No. HSH-1201

1

2

3

For service or sales please contact your local Royal Sovereign office:

Royal Sovereign International Inc.

2 Volvo Drive Rockleigh, N.J. 07647, U.S.A
TEL :[phone]
FAX :[phone]
[e-mail]

Royal Sovereign Canada

164 Oakdale Road, Unit 164 Toronto,
Ontario M3N2S5
TEL : [phone]
FAX : [phone]
[e-mail]

Royal Sovereign International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147,
Australia
TEL : [phone]
FAX : [phone]
[e-mail]

RS Holland B.V.

Planetenweg 75, 2132HM Hoofddorp,
The Netherlands.
Tel : [phone]
Fax : [phone]
[e-mail]