ROWENTA DX1900 User Manual

1

2

3

5

7

8

9

10

11

12

A

6

4

IMPORTANT SAFETY INSTRUCTIONS

Appliance description

1 Spray button

2 Burst of steam and

vertical steam button

3 Variable steam control with

Self Clean Function

4 Auto-off light

5 Thermostat light

6 Temperature control dial

7 Water filling inlet

8 Spray nozzle

9 Release button
10 Cord reel
11 Water tank with maximum

water level indicator

12 Soleplate

A

When using your iron, basic safety precautions should always be
followed,including the following :
Read all instructions before using the iron.

• Use iron only for its intended use.

• To protect against a risk of electric shock, do not immerse the
iron in water or other liquids.

• The iron should always be turned to Minimum (Min) before plugging
or unplugging from outlet. Never yank cord to disconnect from out­let, instead grasp plug and pull to disconnect.

• Do not allow cord to touch hot surfaces. Let iron cool completely
before putting away. Loop cord loosely around iron when storing.

• Always disconnect iron from electrical outlet when filling iron with
water, emptying iron or when not in use.

• Do not operate iron with a damaged cord or if the iron has been
dropped or damaged. To avoid the risk of electric shock, do not
disassemble the iron, ship it to the nearest authorized Rowenta
Appliance Service Center for examination and repair. Incorrect
reassembly can cause a risk of electric shock whenthe iron is used.

• Close supervision is necessary for any appliance being used by or
near children. Do not leave iron unattended while plugged in or on
an ironing board.

• Burns can occur from touching hot metal parts, hot water or steam.
Use caution when you turn a steam iron upside down there may be
hot water in the reservoir.

• The use of accessory attachments is not recommended by Rowenta
Appliance Company and may result infire, electric shock or personal
injury.

SPECIAL INSTRUCTIONS

1.This is either a 1500 / 1600 watt appliance. To avoid an overload, do
not operate another high wattage appliance on the same circuit.

2. If an extension cord is absolutely necessary, the marked electrical
rating of the extension cord should be at least as great as the electri­cal rating of the appliance. Cords rated for less amperage may over­heat. Care should be taken to arrange the cordso that it cannot be
pulled or tripped over.

3. Your Rowenta appliance is intended for householdor professional
use.

SAVE THESE INSTRUCTIONS

Before Use

- Please read all of the Instructions for Use and
the Important Safety Guards carefully.

- Remove all packaging from the iron.

- Remove the soleplate protector.

- It is normal for a small amount of smoke and
a light odor to be produced the first time it is
used. This will quickly disappear.

- Particles may emit from iron during first use.
They are not harmful and sould disppear
after the iron has been alowed.

Helpful Hints

- When ironing, start with fabrics that require a low tempera­ture setting (•) and finish with those which need the highest
temperature (•••).

- Mixed fiber fabrics should be ironed on the temperature for
the most delicate fabrics. For example a shirt that is 60 %
cotton and 40 % polyester should be ironed at the (•) set­ting for synthetics.

- If spray starch is used, spray it onto the reverse side of the
garment. Allow starch to penetrate before ironing by set­ting garment aside for 30 seconds.

- For best results, use a mesh type ironing board to allow
excess steam to escape.

- For delicate fabrics, we recommend carrying out a test on
an unobtrusive area of the garment such as an inner seam.

- Adhere to manufacturer recommendations on garment label.

3 Way Auto-Off

- If the iron is not moved while it isplugged in,
an internal safety switch will turn it off.

- It will turn off in 8 minutes if left vertically or
in 30 seconds if left on its soleplate or tipped
over. A red flashing light indicates that the
auto-off has been activated.

- To switch the iron on again, move the iron
or gently shake it.

Auto off is not on/off switch.
Always unplug iron when it is not use.

Filling with Water

- Ensure the iron is unplugged.

- Slide the variable steam control completely to
the left.

- Rest the iron on heel and tilt it foward
approximately 1 inch. If the iron is equiped
with a covered filling inlet, open the filling
inlet by sliding the cover down.

- Hold the appliance upright so that the water
inlet is horizontal.

- Fill with water (containing no additives) to
the max mark on the water tank. We recommend
using water pitcher rather than filling under the
tap.

- If you need to add water during ironing,
UNPLUG the iron and follow the steps above.

- Ensure iron heats back to temperature after­wards, that means thermostat light will go out.