ROTRONIC AFP1 Users Manual

AFP1 - SmartTool

32.8 %RH

(green LED blinking)

32.8 %RH OK!

(green and red LED on)

75.2 %RH

(red LED blinking)

Measure mode
(auto-power-off

after 5 min)

Power OFF

Measure mode

2s < PRESS < 8s

PRESS < 1s

PRESS > 2s PRESS > 2s

After 30min

PRESS < 1s

PRESS > 10s

After 30min

PRESS > 2s

Humidity adjustment mode

Bluetooth

To connect the AFP1 with the app, please ensure that the
Bluetooth function of your smartphone is enabled.

Home

The current measured values are displayed on the home screen
of the AFP1. Furthermore, you can reach further sub-menus or
features:

- Device overview

- Menu

- Picture mode

- Graphical mode

- Parameter settings

- Parameter units

Data recording

Device overview

Connected devices appear in the “Device Overview”.

Features:

- Rename devices

- Select displayed device

Menu

Home
View current measuring values

Data export
Export saved data

Feedback
Send feedback to ROTRONIC

About
TOTRONIC contact information

Parameter settings

To make alarms or parameters specific settings, just click
the appropriate parameter on the home screen.

Features:

- Set high and low alarms

- Parameter-specific settings

Picture mode

The “Picture Mode” has been implemented to photograph
specific measuring points at which the measurements are
saved directly on the photo.

Graphical mode

In the “Graphical Mode” the current
measured values can be graphically
displayed and viewed. To toggle the
visibility of a certain curve click on the
corresponding parameter symbol.

Data export

Stored data will be saved in the “Data Export” menu and
can be renamed, deleted, or sent via e-mail.

About

The menu "About" includes contact information of all
ROTRONIC AG offices.

- Street address

- Phone number

- Website

- E-mail address

General

Sensor type

Vane anemometer
ROTRONIC HYGROMER® IN-1
NTC

Measuring range

0.5…20 m/s
0…100 %RH

-20…60 °C

Accuracy

±(3 %reading + 0.2 m/s)
±3 %RH (at 25°C)
±0,3 K (at -20...50°C)

Log interval

1 s

LED

1 dual color LED
Red: Battery level too low to maintain proper operation
Green: Battery and communication normal

Power supply

2 x 3 V CR2032 batteries

Power consumption

<5.3 mA

Dimensions measuring head

150 x ø18 mm or 150 x ø28 mm

Dimensions telescopic stick

Retracted: 0,55 m
Withdrawn: 1,2 m

Weight

xxx

Software

„ROTRONIC“ App (iOS, Android)

Delivery

Factory certificate
Short manual instructions
APP (online)
Soft case
Batteries 2 x 3 V (CR2032)

SHORT INSTRUCTION MANUAL

Device Operation via multifunction key

The AFP1 features a multifunction button, which is located on the front, below the sensor head.
The following functions are controlled via the button:

- Switch on with auto-power-off after 5 minutes

- Switch on

- Switch off

- Calibration mode humidity

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may

cause undesired operation.

General description

Congratulations on your purchase of a ROTRONIC AFP1 probe. Please read this short
operating instructions carefully before putting the unit into operation. The document is limited
to the description of the main features and the installation of the device.

The AFP1 probe measures along with humidity and temperature also wind speeds of 0.5 to 20
m/s.

Dimensions

Energy supply

The AFP1 is powered by two CR2032 button batteries.
When inserting or replacing the batteries, place them on top of each other in the battery
compartment slide (observe polarity).

Federal Communication Commission Interference Statement

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

compliance could void the user's authority to operate this equipment.This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired

operation.

environment and are safe for intended operation as described in this manual. The further RF exposure reduction

can be achieved if the product can be kept as far as possible from the user body or set the device to lower output

power if such function is available.This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

This equipment has been tested and found to comply with the limits for a Class B digital device,

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

IMPORTANT NOTE:

Radiation Exposure Statement:

The product comply with the US portable RF exposure limit set forth for an uncontrolled

AFP1 on the Smart Device

After commissioning of AFP1 the LED should light up green. The device is now switched on
and ready to perform measurements. To measure wind speeds ensure that the wind turbine
rotates freely and the sign “AIR IN" points in the direction of the measured air flow.
Operation of AFP1 sensor via the ROTRONIC smartphone application “
available in the App Store (iOS) or in Play Store (Android) for free.
Use the app to display, log and send the desired measurement values by email. Furthermore,
among other things, measurement-specific settings and options can be set.

The “

ROTRONIC" APP

ROTRONIC" which is

Technical specifications

ROTRONIC AG, CH-8303 Bassersdorf

Tel. [phone], www.rotronic.com

ROTRONIC Messgeräte GmbH, D-76275 Ettlingen
Tel. [phone], www.rotronic.de

ROTRONIC SARL, 56, F - 77183 Croissy Beaubourg
Tél. [phone], www.rotronic.fr

ROTRONIC Italia srl, I- 20157 Milano
Tel. [phone], www.rotronic.it

ROTRONIC Instruments (UK) Ltd, West Sussex RH10 9EE
Phone [phone], www.rotronic.co.uk

ROTRONIC Instrument Corp, NY 11788, USA
Phone [phone], www.rotronic-usa.com

ROTRONIC Canada Inc.,Canada L8W 3P7
Phone + 1 416-848-7524, www.rotronic.ca

ROTRONIC Instruments Pte. Ltd., Singapore 159836
Phone [phone], www.rotronic.sg

ROTRONIC Shanghai Rep. Office, Shanghai 200233, China
Phone [phone], www.rotronic.cn