Rosen Aviation 1060 User Manual
ELECTRONIC REVISION
CONTROLLED
Document Number 106282
Rev D
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 2 of 30
Technical Manual, 10.6” HD Widescreen Bulkhead Display
© 2013 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written authorization from Rosen Aviation, LLC,
except as allowed under copyright laws.
Disclaimer of Liability
The information contained in this document is subject to change without notice. Because we are
continuously improving and adding features to our products, Rosen Aviation, LLC reserves the right
to change specifications without prior notice. Rosen Aviation, LLC shall not be liable for technical or
editorial errors or omissions contained herein.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: 541.342.4912
www.rosenaviation.com
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 3 of 30
Contents
1. INTRODUCTION .................................................................................................................5
1.1. System Overview ..........................................................................................................5
1.1.1. Control Options ................................................................................................................. 6
1.1.2. Display Connections ......................................................................................................... 6
2. INSTALLATION GUIDELINES ...........................................................................................6
2.1. Mounting Configurations ...............................................................................................6
2.2. Cooling and Ventilation .................................................................................................7
2.3. Electrical Requirements ................................................................................................7
2.4. Video Connections ........................................................................................................7
2.5. Pinout Connections .......................................................................................................7
3. INITIAL POWER UP ...........................................................................................................7
4. IR REMOTE CONTROL ......................................................................................................8
5. OSD MENU OPTIONS ........................................................................................................9
5.1. Exit ................................................................................................................................9
5.2. User Menu .................................................................................................................. 10
5.2.1. Backlight ......................................................................................................................... 10
5.2.2. Aspect Ratio ................................................................................................................... 10
5.2.3. Scheme .......................................................................................................................... 11
5.2.4. Source ............................................................................................................................ 11
5.2.5. Auto Adjust ..................................................................................................................... 12
5.3. Image Adjust Menu ..................................................................................................... 12
5.3.1. Scheme .......................................................................................................................... 12
5.3.2. Picture-quality Controls ................................................................................................... 12
5.3.3. Reset Scheme ................................................................................................................ 13
5.3.4. Image Adjust Advanced (Submenu) ............................................................................... 13
5.4. Info .............................................................................................................................. 16
6. TECHNICIAN MENU ......................................................................................................... 17
6.1. Advanced Technician Submenu ................................................................................. 18
6.1.1. Factory Reset ................................................................................................................. 18
6.1.2. Comp/RGB 1 .................................................................................................................. 18
6.1.3. 3D Comb Filter ............................................................................................................... 19
6.1.4. Composite Sig (Signal) ................................................................................................... 19
6.1.5. AGC (Automatic Gain Control) ........................................................................................ 19
6.2. Mode Menu ................................................................................................................. 19
6.2.1. Power Mode ................................................................ ................................................... 20
6.2.2. Operation Mode ................................ ................................................................ .............. 20
6.2.3. SDI Overscan ................................................................................................................. 21
6.2.4. SDI Overscan % ............................................................................................................. 21
6.3. OSD Timeout ................................................................ .............................................. 21
6.4. Network ID .................................................................................................................. 22
6.5. Splash Screen ............................................................................................................ 22
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 4 of 30
6.6. Source Mode Submenu .............................................................................................. 22
6.6.1. Momentary Mode ............................................................................................................ 23
6.6.2. Constant Mode ............................................................................................................... 24
7. TECHNICAL REFERENCES AND SUPPORT ................................................................. 24
7.1. Troubleshooting .......................................................................................................... 25
7.2. Cleaning the Display ................................................................................................... 25
7.3. RTCA DO-160F Qualifications for Displays ................................................................ 26
7.4. Supported Video Resolutions ..................................................................................... 28
7.4.1. VGA Resolutions ............................................................................................................ 28
7.4.2. CVBS/Composite Resolutions ........................................................................................ 28
7.4.3. SDI Resolutions .............................................................................................................. 28
8. DEFINITIONS .................................................................................................................... 29
9. REVISION HISTORY ........................................................................................................ 30
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 5 of 30
VGA
SDI
Composite
RosenView MX
1. INTRODUCTION
Rosen’s 10.6” bulkhead display (model 1060-001) brings stunning HD widescreen picture quality
into a small aircraft’s cabin interior.
Although you can use this display in standard analog systems, via Composite and/or VGA video
inputs, the 3G HD-SDI input allows you to use it in high definition systems and connect directly to
a Rosen Blu-ray player.
This manual describes how to install these all-in-one displays onto your aircraft. It contains
everything you need to know to wire the display and confirm that it is functioning correctly.
Note: Only trained and qualified personnel should perform installation and service.
The Outline & Installation drawing and the Technical Manual are available on the Rosen Aviation
website at www.rosenaviation.com.
From the Rosen Aviation home page, select the Products tab and browse by product category.
Please contact Technical Support at 541.342.3802 if you cannot find the documentation that you
need.
1.1. System Overview
The 1060-001 high-definition display enables viewers to watch digital video signals as well as
analog video signals in both high definition and standard resolutions.
Composite and SDI are the default video signals in Auto Detect mode. The Auto Detect mode
continually searches between Composite and SDI for a valid signal and then switches to that
input. In this mode, you remain connected to either input without having to set the source. If both
Composite and SDI are connected and active, then Composite is displayed by default.
Composite, SDI, Component, and RGB are all available in Standard Operation mode. RGB-1
and Component-1 share the VGA connector. Although there are four signal choices, you can
only select from three at any given time.
Figure 1 Single display installation
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 6 of 30
Touching the LCD with excessive force may leave pressure spots
that show in video display. Handle with care.
1.1.1. Control Options
Although the 10.6” display does not have a built-in IR sensor, it provides 3.3V DC
@100mA output to power an external IR receiver. The IR Receiver (P/N 0500-006) and
RC5 Remote Control (P/N 0500-019) (sold separately) enables control options inputs to
adjust the on-screen display settings.
Alternatively, you can control the 10.6” display via a cabin management system using
RS-485 and/or RS-232. For a copy of the RS-232 External Controller Message Formats
(P/N 9002934) or RS485 Network Message Definitions document (P/N 9002933), please
contact Rosen Aviation Technical Support at 541.342.3802.
Note: For directions on operating the optional universal remote control, refer to the user’s
guide enclosed with the remote.
1.1.2. Display Connections
The following cable connections are available:
Optional HD15 Male VGA connector kit (P/N 0300-055)
Required Female 15-pin P1 connector kit (P/N 0300-053)
Optional 90-degree connector kit (P/N 0300-058)
Optional HD BNC Plug to BNC Jack (P/N 106221), an adapter for a standard BNC
connector running CVBS or SDI
The 10.6” display connectors exit straight down. The 90-degree connector kit
(P/N 0300-058) contains the following adapters to route the harnesses away from the
display:
Two – HD BNC Plug to BNC Jack
Two – right-angle BNC Plug to Jack
One – right-angle D-sub 15
One – right-angle HD15
2. INSTALLATION GUIDELINES
2.1. Mounting Configurations
The 10.6 display can be flush mounted to the bulkhead, or secured to a separate mounting
structure from the top and bottom, sides, or back of the unit. Installation requirements include
minimum mounting fasteners: four 8-32 screws.
minimum clearance: ¼” on the sides, top, and bottom; or ⅛” to the back of the unit; or
secure the display to an aluminum structure to act as a heat sink.
Consult the Outline and Installation drawing to assist with the installation process. Pay close
attention to the dimensions and fastener depths required when considering installation
requirements.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 7 of 30
Do not plug or unplug the display connector while power is
applied.
When cycling power, leave unit off for 20 seconds before restoring
power.
2.2. Cooling and Ventilation
The 10.6 chassis does not have vent holes for conductive cooling, nor does it require any
external forced-air cooling.
2.3. Electrical Requirements
Nominal voltage 28VDC / .66 A
Max Power Consumption: 20 W
2.4. Video Connections
The 1060-001 display uses the following connectors.
Figure 2 10.6 bulkhead display connections
2.5. Pinout Connections
There are several ways to connect the remote display system to an aircraft’s entertainment
system.
Pay close attention to the pinout descriptions on the Outline and Installation drawings to assist in
completing the wiring connections.
Note: This display is for entertainment purposes only; connect to a non-critical power bus.
3. INITIAL POWER UP
Make sure that power is turned off and perform the following steps.
1. Ensure a low impedance ground connection on the chassis from any one of the 8-32
mounting holes.
2. Connect the power supply and video source to the appropriate connectors.
3. An optional, 90-degree connector kit (P/N 0300-058) allows you to route the harness
towards the back, if desired.
4. Supply power and wait for a video signal on the screen. The default video mode is
Auto Detect and the default power mode is Auto On.
5. The display will search for a valid video signal by priority—Composite first and then
SDI. To use VGA, change the Operation Mode from Auto Detect to Standard
in the on-screen display (OSD).
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 8 of 30
Note: The AUTO button works
only when an RGB source is
active. The MUTE and
VOLUME ± buttons are not
used.
How it Works
SOURCE
Switches between any enabled video inputs. Press the SOURCE
button twice to switch inputs. The first command sent will only display
the current source name in the upper-left corner of the monitor; the
second command switches the source.
POWER
Turns the display’s power on and off.
MENU
Opens the Main Menu to access other settings and fine-tune the
display’s picture quality. For details, see Section 5, OSD Menu
Options, on page 9.
EXIT
Closes the OSD and saves settings. Exit does not close control bars.
ENTER
Accepts changes to menu settings. Selects menu options, accepts
settings, and closes the control bars.
◄►▲▼
Controls the navigation in the on-screen display menus. Navigate
between the OSD menu pages, options, and change settings.
ASPECT
Changes the aspect ratio or proportions of the picture depending on
the video format. Switches between Full Screen, Pillar Box, and
Letterbox Expanded. See also Section 5.2.2, Aspect Ratio, on
page 10.
INFO
Opens the Info page on the OSD. Use INFO to verify source and
resolution values. Also quick access to open the Technician Menu.
See also Section 5.4, Info, on page 16.
AUTO
(RGB only) Performs an auto-adjust function without a menu. Forces
the display to evaluate the RGB signals and ensure it is interpreting
them correctly. See also Section 5.2.5, Auto Adjust, on page 12.
BRIGHT ±
Opens the backlight control bar. See also Section 5.2.1, Backlight, on
page 10.
4. IR REMOTE CONTROL
The 10.6” displays may use an optional remote control to adjust the on-screen display (OSD)
settings. The instructions in this manual use the RC5 IR remote in describing how to navigate the
OSD. Table 1 shows the RC5 IR remote layout and the button descriptions.
Table 1 RC5 IR remote control
Rosen Aviation 10.6” HD Widescreen Bulkhead Display
Document Number: 106282
Revision: D
Date: 03/20/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 9 of 30
Press ► to access
the menu page
options
Press ► to access
the menu option
values
Press ▼ to
access menu
pages. The
selected menu
page is
highlighted.
5. OSD MENU OPTIONS
The OSD contains screen settings and options in menus and informational readouts that display
over the image, as shown below. Press MENU on the remote to open the Main Menu, as shown in
Section 5.1.
Press the ▲▼ buttons to navigate within the menu pages. Press the ►◄ buttons to navigate
between the menu page, options, and values columns. The yellow highlighted area shows the
currently selected option in the menu.
Figure 3 OSD menu pages
The available menu options will vary depending on which source signal is active.
Press MENU to choose a setting or an option.
Select the Back option to switch menu pages.
Press EXIT to close the OSD and save settings.
Note: The on-screen display will timeout and close automatically after no screen activity for a
preset amount of time, which is adjustable on the Technician MenuOSD Timeout option. See
Section 6.3, OSD Timeout on page 21.
5.1. Exit
Use Exit to close the OSD. When you press MENU, the OSD opens to this screen, as shown
below. Press MENU again to close the OSD from this screen.
Press the ▲▼ buttons to access the other menu pages in the OSD.
From other settings within the OSD, press EXIT on the remote control to close the OSD.
Figure 4 Opening screen for the Main Menu
Loading...