Page 1
Quick Start Guide
00825-0100-4328, Rev 01
January 2019
Rosemount™ 326T Temperature Transmitter
Page 2
2
Page 3
Quick Start Guide Contents
00825-0100-4328 January 2019
Contents
Chapter 1 Introduction.................................................................................................................. 5
1.1 Functions and features..................................................................................................................... 5
Chapter 2 Installation.....................................................................................................................7
2.1 Mounting the transmitter.................................................................................................................7
2.2 Connect the transmitter................................................................................................................... 7
Chapter 3 Operation...................................................................................................................... 9
3.1 Display elements.............................................................................................................................. 9
3.2 Parameter settings........................................................................................................................... 9
3.3 Adjustable parameters................................................................................................................... 10
3.4 Operating modes........................................................................................................................... 10
Chapter 4 Temperature resistance............................................................................................... 11
Chapter 5 Product certifications...................................................................................................13
5.1 European directive information...................................................................................................... 13
5.2 Ordinary location information........................................................................................................ 13
5.3 3-A® certification............................................................................................................................13
5.4 Other industry certifications...........................................................................................................13
Chapter 6 Factory settings........................................................................................................... 15
Quick Start Guide 3
Page 4
Contents Quick Start Guide
January 2019 00825-0100-4328
4 Quick Start Guide
Page 5
Quick Start Guide Introduction
00825-0100-4328 January 2019
1 Introduction
The Rosemount 326T Temperature Transmitter detects media temperature and converts
it into an analog output signal (4 - 20 mA).
1.1 Functions and features
The temperature transmitter converts the measured signal into a temperatureproportional analog signal. Depending on the parameter setting, the output signal is:
• 4-20 mA with setting OU = I
• 20-4 mA with setting OU = Ineg
The temperature transmitter can scale the analog signal to accommodate the application.
For more technical data, see the Rosemount™ 326T Temperature Transmitter Product
Data Sheet or Emerson.com/Rosemount.
Maximum measuring range when OU = I
• MAW = initial value of the measuring range
• MEW = final value of the measuring range
Note
The minimum difference between ASP and AEP is 9 °F (5 °C).
If the temperature is within the measuring range, the output signal is between 4-20 mA. If
the temperature is outside the measuring range, the output signal is between these
ranges:
Measuring range scaled when OU = I
• ASP = analog start point
• AEP = analog end point
Temperature condition
Temperature > AEP 20-20.6 mA 4-3.7 mA
Temperature > MEW 20.6 mA 3.7 mA
Temperature < ASP 4-3.7 mA 20-20.6 mA
Quick Start Guide 5
Output signal when OU = I Output signal when OU = Ineg
Page 6
Introduction Quick Start Guide
January 2019 00825-0100-4328
Temperature condition Output signal when OU = I Output signal when OU = Ineg
Temperature < MAW 3.7 mA 20.6 mA
Note
In a fault condition, the output signal reacts according to the FOU parameter.
6 Quick Start Guide
Page 7
Quick Start Guide Installation
00825-0100-4328 January 2019
2 Installation
This section provides instructions for mounting and connecting the temperature
transmitter.
2.1 Mounting the transmitter
Follow these instructions to mount the temperature transmitter.
Note
If installing in a 3-A compliant environment, follow 3-A standards for installation.
Procedure
1. Position the transmitter to the desired orientation.
2. Install the clamp following recommended torque values provided by the clamp
manufacturer.
2.2 Connect the transmitter
Follow these instructions to connect the temperature transmitter for two-wire or four-wire
operations.
CAUTION
• A certified electrician must wire the temperature transmitter.
• Adhere to national and international regulations when wiring the temperature
transmitter.
Voltage supply to EN 50178, SELV, PELV / "supply class 2" to cULus.
Procedure
1. Disconnect power from the temperature transmitter.
2. Connect the temperature transmitter according to these wiring diagrams.
Quick Start Guide 7
Page 8
Installation Quick Start Guide
January 2019 00825-0100-4328
Figure 2-1: Two-wire operation
Pin 1 L+
Pin 2 Analog signal for temperature
Figure 2-2: Four-wire operation
Pin 1 L+
Pin 2 Analog signal for temperature
Pin 3 L-
Pin 4 IO-Link
8 Quick Start Guide
Page 9
Quick Start Guide
00825-0100-4328 January 2019
Operation
3 Operation
This section provides information for using the temperature transmitter.
3.1 Display elements
The front of the temperature transmitter includes an alphanumeric display and LED
indicators.
A. Current temperature in °C
B. Current temperature in °F
C. Seven-segment LED display (4 digits)
3.2 Parameter settings
Use an IO-Link capable tool to read current process values and modify parameter values.
3.2.1
3.2.2
General information
The temperature transmitter uses an IO-Link communication interface that requires an IOLink master for operation.
IO-Link enables direct access to process and diagnostic data and allows the setting of
parameter values.
IO-Link information
The IODDs necessary for configuring the IO-Link device, detailed information about
process data structure, diagnostic information, parameter addresses and the necessary
Quick Start Guide 9
Page 10
Operation Quick Start Guide
January 2019 00825-0100-4328
information about the required IO-Link hardware and software are available at
Emerson.com/Rosemount
3.3 Adjustable parameters
Use IO-Link software to configure these parameters.
Parameter Description
OU2 Output function: analog signal is 4-20 mA (I) or 20-4 mA (Ineg)
ASP2 Analog start point for the measured temperature value.
AEP2 Analog end point for the measured temperature value. The minimum
difference between ASP2 and AEP2 is 9 °F (5 °C).
COF Zero point calibration. Offsets the zero point ± 18 °F in steps of .18 °F (±
10 °C in steps of 0.1 °C).
FOU2 Behavior of the output after a fault.
• ON: the analog signal is driven to 21.1 mA.
• OFF: the analog signal is driven to 3.5 mA.
Uni Sets the temperature unit in °F or °C.
Update rate of display The rate at which the transmitter updates the displayed temperature
measurement.
• d1: 50 ms
• d2: 200 ms
• d3: 600 ms
Orientation of display rd: rotates the display by 180°.
3.4 Operating modes
The temperature transmitter uses different operating modes depending on the measured
temperature.
After turning on the temperature transmitter the temperature transmitter displays the
current measured temperature and the analog output provides a signal proportional to
the measured temperature.
If the temperature is outside of the measuring range the temperature transmitter displays
OL or UL.
10 Quick Start Guide
Page 11
Quick Start Guide Temperature resistance
00825-0100-4328 January 2019
4 Temperature resistance
This graph shows the reduction of maximum operation time based on process
temperature.
Quick Start Guide 11
Page 12
Temperature resistance Quick Start Guide
January 2019 00825-0100-4328
12 Quick Start Guide
Page 13
Quick Start Guide Product certifications
00825-0100-4328 January 2019
5 Product certifications
5.1 European directive information
The most recent revision of the EC Declaration of Conformity can be found at
Emerson.com/Rosemount.
5.2 Ordinary location information
As standard, this product has been examined and tested to determine that the design
meets the basic electrical, mechanical, and fire protection requirements by a nationally
recognized test laboratory (NRTL) as accredited by the Federal Occupational Safety and
Health Administration (OSHA).
Voltage supply to EN 50178, SELV, PELV / "supply class 2" to cULus.
5.3 3-A® certification
This product is authorized to display the 3-A symbol. Ensure gaskets and process
connection accessories selected for installation meet both the application and 3-A
requirements. A certificate of compliance is available at Emerson.com/Rosemount.
5.4 Other industry certifications
All Rosemount 326T transmitter surfaces and materials which come into contact with
process medium comply with the following regulations:
Quick Start Guide 13
Page 14
Product certifications Quick Start Guide
January 2019 00825-0100-4328
14 Quick Start Guide
Page 15
Quick Start Guide Factory settings
00825-0100-4328 January 2019
6 Factory settings
Use this worksheet to reference factory default settings and record user-modified settings.
Parameter Factory default setting User-defined setting
OU I
COF 0.0
FOU OFF
Quick Start Guide 15
Page 16
*00825-0100-4328*
00825-0100-4328
Rev. 01
2019
Global Headquarters
Emerson Automation Solutions
6021 Innovation Blvd
Shakopee, MN 55379, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
RFQ.RMD-RCC@Emerson.com
Linkedin.com/company/Emerson-Automation-Solutions
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/RosemountMeasurement
North America Regional Office
Emerson Automation Solutions
8200 Market Blvd.
Chanhassen, MN 55317, USA
+1 800 999 9307 or +1 952 906 8888
+1 952 949 7001
RMT-NA.RCCRF@Emerson.com
©
2019 Emerson. All rights reserved.
Emerson Terms and Conditions of Sale are available upon request. The Emerson logo is a
trademark and service mark of Emerson Electric Co. Rosemount is mark of one of the
Emerson family of companies. All other marks are the property of their respective owners.
Loading...