Rosemount 3095MFC Data sheet

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Rosemount Compact Orifice Flowmeter Series

INTEGRATED DESIGN FOR LIMITED STRAIGHT PIPE RUN, CLOSED LOOP CONTROL, AND GENERAL PURPOSE MONITORING APPLICATIONS

• Reduced installation cost compared to a traditional orifice plate

• Accurate and repeatable

• Easy-to-install direct mount assembly

• Self-centering

• Based on ASME/ISO corner tap design

• Patented technology

Flowmeter Series

Content

The Rosemount 405 Compact Orifice Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2

Rosemount DP-Flow Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2

Rosemount 3051SFC Compact Orifice Flowmeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4

Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 11

Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16

Rosemount 3095MFC Compact Orifice Mass Flowmeter . . . . . . . . . . . . . . . . . . . . . . . . . . page 20

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20

Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 26

Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 28

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 29

Rosemount 405 Compact Orifice Primary Element. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 32

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 32

Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 36

Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 38

HART Configuration Data Sheet (CDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 40

F

OUNDATION fieldbus

™

Configuration Data Sheet (CDS) . . . . . . . . . . . . . . . . . . . . . . . . . . page 43

Fluid Data Sheet (FDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 46

www.rosemount.com

Rosemount Compact Orifice

Rosemount pressure transmitters

combined with the Rosemount 405 Compact

Orifice create Best-in-Class Flowmeters

3051SFC Compact

Orifice Flowmeter

3095MFC Compact

Orifice Mass Flowmeter

405C

405P

Flowmeter Series

The Rosemount 405 Compact Orifice Series

Best-in-Class Integrated DP Flowmeters

By integrating Rosemount pressure transmitters with the 405 Compact Orifice Series primary element, Rosemount provides the highest performing DP Flowmeters. This fully integrated flowmeter eliminates the need for fittings, tubing, valves, adapters, manifolds, and mounting brackets, thereby reducing welding and installation time.

Less Expensive than an Orifice Plate Installation

Direct mounting minimizes total installed cost by reducing engineering, procurement, labor, and material expenditures while offering unsurpassed utility.

Direct Mount

A 3-valve isolation manifold and 1-in (25 mm) thick wafer-style body allows direct mounting while eliminating field connections between the process and the differential pressure-measuring device. The integral configuration results in a robust, inexpensive, and easy-to-install assembly.

Accurate and Repeatable

The 405C Conditioning Orifice is ideal for limited pipe run measurements in gas, liquid, or steam applications (8-in. (200 mm) nominal diameter and smaller lines). The 405C Conditioning Orifice delivers consistent and accurate measurements one would expect from traditional orifice plate technology.

Centering Mechanism

Improper centering of any orifice type device can cause an error of up to ±5% in small line sizes. A centering mechanism independent of flange rating is standard with the 405 Compact Orifice Series.

Annubar® Flowmeter Series: Rosemount

3051SFA ProBar and 285

The state-of-the-art, fifth generation Rosemount 485 Annubar combined with the 3051S or 3095 MultiVariable transmitter creates an accurate, repeatable and dependable insertion-type flowmeter. The Rosemount 285 provides a commercial product offering for your general purpose applications.

Compact Orifice Flowmeter Series: Rosemount 3051SFC, 3095MFC, and 405

Compact Orifice Flowmeters can be installed between existing flanges, up to a Class 600 (PN100) rating. In tight fit applications, a conditioning orifice plate version is available, requiring only two diameters of straight run upstream.

®

, 3095MFA Mass ProBar®, 485,

Based on ASME/ISO Corner Tap Design

The incorporation of design features from proven standards results in a product that performs in a predictable manner and operates on well-known principles.

Advanced PlantWeb

Rosemount orifice flowmeters power PlantWeb through a scalable architecture, advanced diagnostics, and MultiVariable capabilities. This reduces operational and maintenance expenditures while improving throughput

and utilities management.

Rosemount DP-Flow Solutions

Integral Orifice Flowmeter Series: Rosemount 3051SFP

ProPlate®, 3095MFP Mass ProPlate, and 1195

These integral orifice flowmeters eliminate the inaccuracies that become more pronounced in small orifice line installations. The completely assembled, ready to install flowmeters reduce cost and simplify installation.

Orifice Plate Primary Element Systems: Rosemount 1495 and 1595 Orifice Plates, 1496 Flange Unions and 1497 Meter Sections

A comprehensive offering of orifice plates, flange unions and meter sections that is easy to specify and order. The 1595 Conditioning Orifice provides superior performance in tight fit applications.

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

®

Functionality

2

Product Data Sheet

Rosemount 3051SFC Compact Orifice Flowmeter

See ordering information on page 16.

• Combines the Rosemount 3051S scalable pressure transmitter with the 405 Compact Orifice Primary

• Accuracy up to ±0.80% of volumetric rate

• Remote display and interface assembly enables direct mounting with “at-grade” operator interface

• F

OUNDATION

®

fieldbus protocol available

• Ideal fluid type: liquid

Rosemount 3095MFC Compact Orifice Mass Flowmeter

See ordering information on page 29.

• Combines the Rosemount 3095MV MultiVariable mass flow transmitter with the 405 Compact Orifice Primary

• Accuracy up to ±0.70% of mass flow rate

• Measures differential pressure, static pressure, and process temperature (remotely) all in one flowmeter assembly

• Dynamically calculates compensated mass flow

• Ideal fluid types: gas and steam

Rosemount 405 Compact Orifice Primary

See ordering information on page 38.

• Integral manifold head allows direct mounting of DP transmitters

• Ideal fluid types: liquid, gas, and steam

• Accuracy up to ±0.5% of discharge coefficient uncertainty

• Direct mounting capability to ANSI 600# rating

• Self-centering alignment ring

3095MFC Compact Orifice

Mass Flowmeter

405C Conditioning

Orifice

3051SFC Compact

Orifice Flowmeter

405P Compact

Orifice

00813-0100-4810, Rev HA March 2008

405 Compact Orifice Series Selection Guide

Rosemount Compact Orifice

Flowmeter Series

3

Rosemount Compact Orifice Flowmeter Series

Rosemount 3051SFC Compact Orifice Flowmeter

SPECIFICATIONS

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Performance

System Reference Accuracy

Percent (%) of volumetric flow rate TABLE 1. 3051SFC Compact Orifice Flowmeter

Classic

(8:1 flow

Typ e Beta

3051SFCC

3051SFCP

(1) Line sizes 1/2-in. (15mm).

(2) Line sizes 1-in. to 1 1/2-in. (25mm to 40mm).

(3) Line sizes 2-in. to 12-in. (50mm to 300mm).

(4) For 0.65 beta and ReD< 10,000 add an additional ± 0.5% to the

(1)

(2)

(3)

Discharge Coefficient Uncertainty.

0.4

0.65

0.4

0.65

0.4

0.65

0.4

0.65

turndown)

±1.05% ±1.35%

±2.45% ±2.35% ±2.30%

(4)

±2.00% ±1.90% ±1.85%

(4)

±1.55% ±1.45% ±1.40%

(4)

Ultra

(8:1 flow

turndown)

±0.85% ±1.20%

Repeatability

±0.1%

Ultra for

(14:1 flow

turndown)

±0.80% ±1.15%

Functional

Service

• Liquid

•Gas

•Steam

Flow

4–20 mA/HART

Zero and Span Adjustment

Zero and span values can be set anywhere within the range. Span must be greater than or equal to the minimum span.

Output

Two-wire 4–20 mA is user-selectable for linear or square root output. Digital process variable superimposed on 4–20 mA signal, available to any host that conforms to the HART protocol.

Power Supply

External power supply required.

Standard transmitter (4–20 mA): 10.5 to 42.4 V dc with no load

3051S HART Diagnostics transmitter: 12 to 42 Vdc with no load

Line Sizes

•1/2-in. (15 mm) – not available for the 3051SFCC

• 1-in. (25 mm) – not available or the 3051SFCC

1

/2-in. (40 mm) – not available for the 3051SFCC

•1

• 2-in. (50 mm)

• 3-in. (80 mm)

• 4-in. (100 mm)

• 5-in (125 mm)

• 6-in. (150 mm)

• 8-in. (200 mm)

• 10-in. (250 mm)

• 12-in (300 mm)

Performance Statement Assumptions

• Measured pipe I.D

Sizing

Contact an Emerson Process Management representative for assistance. A Configuration Data Sheet is required prior to order for application verification.

4

Product Data Sheet

Voltage (V dc)

Load (Ohms)

Operating

Region

1387

1000

500

0

10.5 20 30

42.4

Voltage (V dc)

Load (Ohms)

Operating

Region

1322

1000

500

0

12.0 20 30

42.4

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Load Limitations

Maximum loop resistance is determined by the voltage level of the external power supply, as described by:

Standard Transmitter

Maximum Loop Resistance = 43.5 * (Power Supply Voltage – 10.5)

The HART communicator requires a minimum

loop resistance of 250Ω for communication.

3051S HART Diagnostics Transmitter (option code DA1)

Maximum Loop Resistance = 43.5 * (Power Supply Voltage – 12.0)

The HART communicator requires a minimum

loop resistance of 250Ω for communication.

ASP™ Diagnostics Suite for HART (Option Code DA1)

The 3051S provides Abnormal Situation Prevention indication for a breakthrough in diagnostic capability. The New 3051S ASP™ Diagnostics Suite for HART includes Statistical Process Monitoring (SPM), variable logging with time stamp and advanced process alerts. The enhanced EDDL graphic display provides an intuitive and user-friendly interface to better visualize these diagnostics.

The integral SPM technology calculates the mean and standard deviation of the process variable 22 times per second and makes them available to the user. The 3051S uses these values and highly flexible configuration options for customization to detect many user-defined or application specific abnormal situations (e.g. detecting plugged impulse lines and fluid composition change). Variable logging with time stamp and advanced process alerts capture valuable process and sensor data to enable quick troubleshooting of application and installation issues.

FOUNDATION fieldbus

Power Supply

External power supply required; transmitters operate on 9.0 to

32.0 V dc transmitter terminal voltage.

Current Draw

17.5 mA for all configurations (including LCD display option)

OUNDATION fieldbus Parameters

F

Schedule Entries 14 (max.) Links 30 (max.) Virtual Communications Relationships (VCR) 20 (max.)

Standard Function Blocks

Resource Block

• Contains hardware, electronics, and diagnostic information.

Transducer Block

• Contains actual sensor measurement data including the sensor diagnostics and the ability to trim the pressure sensor or recall factory defaults.

LCD Block

• Configures the local display.

2 Analog Input Blocks

• Processes the measurements for input into other function blocks. The output value is in engineering or custom units and contains a status indicating measurement quality.

PID Block with Auto-tune

• Contains all logic to perform PID control in the field including cascade and feedforward. Auto-tune capability allows for superior tuning for optimized control performance.

Backup Link Active Scheduler (LAS)

The transmitter can function as a Link Active Scheduler if the current link master device fails or is removed from the segment.

Software Upgrade in the Field

Software for the 3051S with F upgrade in the field using the F Device Software Download procedure.

PlantWeb Alerts

Enable the full power of the PlantWeb digital architecture by diagnosing instrumentation issues, communicating advisory, maintenance, and failure details, and recommending a solution.

Advanced Control Function Block Suite (Option Code A01)

Input Selector Block

• Selects between inputs and generates an output using specific selection strategies such as minimum, maximum, midpoint, average, or first “good.”

Arithmetic Block

• Provides pre-defined application-based equations including flow with partial density compensation, electronic remote seals, hydrostatic tank gauging, ratio control and others.

Signal Characterizer Block

• Characterizes or approximates any function that defines an

input/output relationship by configuring up to twenty X, Y coordinates. The block interpolates an output value for a given input value using the curve defined by the configured coordinates.

Integrator Bock

• Compares the integrated or accumulated value from one or

two variables to pre-trip and trip limits and generates discrete output signals when the limits are reached. This block is useful for calculating total flow, total mass, or volume over time.

OUNDATION fieldbus is easy to

OUNDATION fieldbus Common

5

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Output Splitter Block

• Splits the output of one PID or other control block so that the PID will control two valves or other actuators.

Control Selector Block

• Selects one of up to three inputs (highest, middle, or lowest) that are normally connected to the outputs of PID or other control function blocks.

Block Execution Time

Resource Transducer LCD Block Analog Input 1, 2 20 milliseconds PID with Auto-tune 35 milliseconds Input Selector 20 milliseconds Arithmetic 20 milliseconds Signal Characterizer 20 milliseconds Integrator 20 milliseconds Output Splitter 20 milliseconds Control Selector 20 milliseconds

Fully Compensated Mass Flow Block (Option Code H01)

Calculates fully compensated mass flow based on differential pressure with external process pressure and temperature measurements over the fieldbus segment. Configuration for the mass flow calculation is easily accomplished using the Rosemount 3095 Engineering Assistant.

ASP™ Diagnostics Suite for F Code D01)

The 3051S ASP™ Diagnostics Suite for F provides Abnormal Situation Prevention indication and enhanced EDDL graphic displays for easy visual analysis.

The integral Statistical Process Monitoring (SPM) technology calculates the mean and standard deviation of the process variable 22 times per second and makes them available to the user. The 3051S uses these values and highly flexible configuration options for customization to detect many user-defined or application specific abnormal situations (e.g. detecting plugged impulse lines and fluid composition change).

OUNDATION fieldbus (Option

OUNDATION fieldbus

Process Temperature Limits

Direct Mount Transmitter

• 450 °F (232 °C)

Remote Mount Transmitter

• 850 °F (454 °C) – Stainless Steel

Transmitter Temperature Limits

Ambient

• –40 to 185 °F (–40 to 85 °C)

• With Integral Display

Storage

• –50 to 230 °F (–46 to 110 °C)

• With Integral Display: –40 to 185 °F (–40 to 85 °C)

• With Wireless Output (Code X): –40 to 185 °F (–40 to 85 °C)

(1)

: –40 to 175 °F (–40 to 80 °C)

Differential Pressure Limits

Maximum differential pressure (DP) up to 800 inH2O.

Pressure Limits

Direct Mount Transmitter

• Pressure retention per ANSI B16.5 600# or DIN PN

(2)

Static Pressure Limits

• Range 1A: Operates within specification between static line pressures of 0.5 psia to 2000 psig (0.03 to 138 bar)

• Ranges 2A– 3A: Operates within specifications between static line pressures of 0.5 psia and 3626 psig (0.03 bar-A to 250 bar-G)

Vibration Limits

Qualified per IEC61298-3 (1998) for field with high vibration level or pipeline with high vibration level (10-60Hz 0.21mm displacement peak amplitude / 60 - 500Hz 3g).

The weight and length of the transmitter assembly shall not exceed

5.8 lbs and 7.75-in.

Burst Pressure Limits

Coplanar or traditional process flange

• 10000 psig (689,5 bar)

Wireless Self-Organizing Networks

Output

Wireless enabled HART.

Transmit Rate

User selectable, 15 sec. to 60 min.

Power Module

Replaceable, Intrinsically Safe Lithium-thionyl chloride Power Module with polybutadine terephthalate (PBT) enclosure. Five-year life at one minute transmit rate: ten-year life at ten minute transmit rate.

(1) Reference conditions are 70 °F (21 °C), and routing data for three

additional network devices. NOTE Continuous exposure to ambient temperature limits, -40 °F (-40 °C) or 185 °F (85 °C), may reduce specified life by less than 20 percent.

6

(1)

(1) LCD display may not be readable and LCD updates will be

slower at temperatures below -4 °F (-20 °C).

(2) Static pressure selection may effect pressure limitations.

Product Data Sheet

T

c

T

d

Td = Dead Time T

c

= Time Constant

Pressure Released

Response Time = Td+T

c

63.2% of Total Step Change

Time

0%

100%

36.8%

Transmitter Output vs. Time

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Overpressure Limits

Transmitters withstand the following limits without damage:

• Range 1A: 2000 psig (138 bar)

• Ranges 2A–3A: 3626 psig (250 bar)

TABLE 2. Overpressure Limits

Standard Typ e

(1)

Carbon Steel Rating

Stainless Steel Rating

ANSI/ASME Class 150 285 (20) 275 (19) ANSI/ASME Class 300 740 (51) 720 (50) ANSI/ASME Class 600 1480 (102) 1440 (99)

At 100 °F (38 °C), the rating decreases with increasing temperature.

DIN PN 10/40 580 (40) 580 (40) DIN PN 10/16 232 (16) 232 (16) DIN PN 25/40 580 (40) 580 (40)

At 248 °F (120 °C), the rating decreases with increasing temperature.

(1) Carbon Steel and Stainless Steel Ratings are measured in

psig (bar).

Humidity Limits

• 0–100% relative humidity

Turn-On Time

Performance within specifications less than 2 seconds (typical) after power is applied to the transmitter

Damping

Analog output response to a step input change is user-selectable from 0 to 60 seconds for one time constant. This software damping is in addition to sensor module response time

Dynamic Performance

(1)

Failure Mode Alarm

HART 4-20mA (output option codes A and B)

If self-diagnostics detect a gross transmitter failure, the analog signal will be driven offscale to alert the user. Rosemount standard (default), NAMUR, and custom alarm levels are available (see Table 3).

High or low alarm signal is software-selectable or hardware-selectable via the optional switch (option D1).

TABLE 3. Alarm Configuration

High Alarm Low Alarm

Default ≥ 21.75 mA ≤ 3.75 mA NAMUR compliant Custom levels

(1) Analog output levels are compliant with NAMUR

recommendation NE 43, see option codes C4 or C5.

(2) Low alarm must be 0.1 mA less than low saturation and high

alarm must be 0.1 mA greater than high saturation.

3051S Safety-Certified Transmitter Failure Values

Safety accuracy: 2.0% Safety response time: 1.5 seconds

(1) A 2% variation of the transmitter mA output is allowed before

a safety trip. Trip values in the DCS or safety logic solver should be derated by 2%.

(1)

(2)

≥ 22.5 mA ≤ 3.6 mA

20.2 - 23.0 mA 3.6 - 3.8 mA

(1)

Total Response Time (Td + Tc)

Dead Time (Td) Update Rate 3051S 22 times per second 22 times per second

(1)

3051S_C, Ranges 2A - 3A:

Range 1A:

(5)

(1) Does not apply to wireless output code X. See “Wireless Self-Organizing Networks” on page 6 for wireless transmit rate.

(2) Dead time and update rate apply to all models and ranges; analog output only

(3) Transmitter fieldbus output only, segment macro-cycle not included.

(4) Nominal total response time at 75 °F (24 °C) reference conditions. For option code DA1, add 45 milliseconds (nominal) to 4-20 mA (HART®) total

response time values.

(5) For option code DA1, dead time (Td) is 90 milliseconds (nominal).

4 - 20 mA (HART®)

(4)

:

100 milliseconds 255 milliseconds

45 milliseconds (nominal) 97 milliseconds

(2)

Fieldbus protocol

152 milliseconds 307 milliseconds

(3)

Typical Transmitter Response Time

7

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Physical

Temperature Measurement

Remote RTD

• 100 Ohm platinum with series with Rosemount 644 housing) Model 0078D21N00A025T32Ex Connection Head: 00644-4410-0011

• Standard RTD cable is shielded armored cable, length is 12 feet (3.66 m)

Thermowell with Remote RTD

1

/2-in. x 1/2-in. NPT, 316 SST

•

NOTE

Remote temperature measurement is not available for and 11/2-in. sizes.

Electronic Connections for Remote Mount

1

/2–14 NPT, G1/2, and M20 × 1.5 (CM20) conduit. HART interface

connections fixed to terminal block for output code A

Material of Construction

Body/Plate

•316 SST

• 50 micro-inch Ra surface finish

Manifold Head/Valves

•316 SST

Flange Studs and Nuts

• Customer supplied

• Available as a spare part

Transmitter Connection Studs and Nuts

• Studs– A193 Grade B8M.

• Nuts– A194 Grade 8M.

Gasket and O-rings

• Gaskets are customer supplied.

• Durlon 8500 fiber gaskets are recommended. Consult an Emerson Process Management representative for use with other gaskets.

• Available as a spare part

NOTE

Gaskets and O-rings must be replaced when the 405 is disassembled.

1

/2-in. NPT nipple and union (078

1

/2-in., 1-in.,

Process-Wetted Parts

Integral Manifolds

•316 SST

• Hastelloy C-276

Remote Manifolds

•316 SST

• Hastelloy C-276

Transmitter Vent Valves and Process Flanges

•316 SST

• Hastelloy C-276

• Glass-filled PTFE O-rings

Process Isolating Diaphragms

• 316L SST

• Hastelloy C-276

Integral Manifold O-Rings

• PTFE/Graphite

Non-Wetted Parts

Sensor Module Fill Fluid

• Silicone oil

• Inert Fill optional

Cover O-rings

•Buna-N

Remote Mounting Brackets

• SST

Electronic Housing

• Low copper aluminum, NEMA 4x, IP65

• SST (optional)

Paint

• Polyurethane

Bolts

•CS

Transmitter Connections

Remote Mount

• Available with connections

Orifice Type

• Square edged, Wafer style

Orifice Pressure Taps

• Corner

1

/4-in. (standard) or 1/2-in. (option code E)

Process Connections

Mounts between the following flange configurations:

ASME B16.5 (ANSI)

Class 150

Class 300

Class 600

ANSI alignment ring is included as standard when ordering.

8

DIN JIS

PN16 (option code G)

PN40 (option code H)

PN100 (option code H)

10k (option code B)

20k (option code R)

40k (option code S)

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Typical Orifice Hole Sizes (For 3051SFCC)

Beta is calculated by: (β) = dC / Pipe ID, where the calculated bore is equal to 2 x typical orifice hole size (d shows the diameter of each of the four typical orifice holes.

TABLE 4. β = 0.4

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.249 (6.325)

1-in. (25 mm) Not Available 0.420 (10.668)

1

/2-in. (40 mm) Not Available 0.644 (16.358)

1 2-in. (50 mm) 0.413 (10.490) 0.827 (21.006) 3-in. (80 mm) 0.614 (15.596) 1.227 (31.166) 4-in. (100 mm) 0.805 (20.447) 1.610 (40.894) 5-in. (125 mm) 1.009 (25.629) 2.019 (51.283) 6-in. (150 mm) 1.213 (30.810) 2.426 (61.620) 8-in. (200 mm) 1.596 (40.538) 3.192 (81.077) 10-in. (250 mm) 2.004 (50.902) 4.008 (101.80) 12-in. (300 mm) 2.400 (60.960) 4.800 (121.92)

TABLE 5. β = 0.65

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.404 (10.262)

1-in. (25 mm) Not Available 0.682 (17.323)

1

/2-in. (40 mm) Not Available 1.047 (26.594)

1 2-in. (50 mm) 0.620 (15.748) 3-in. (80 mm) 0.997 (25.324) 1.994 (50.648) 4-in. (100 mm) 1.308 (33.223) 2.617 (66.472) 5-in. (125 mm) 1.640 (40.640) 3.281 (83.34) 6-in. (150 mm) 1.971 (50.063) 3.942 (100.127) 8-in. (200 mm) 2.594 (65.888) 5.188 (131.775) 10-in. (250 mm) 3.257 (82.728) 6.513 (165.43) 12-in. (300 mm) 3.900 (99.060) 7.800 (198.120)

(1) Measurement is in inches (millimeters)

(2) Tolerance = ±0.002-in.

(3) Beta (β) = 0.60-in. (15.24 mm) for 2-in. line size only.

= 2d). The table below

C

(3)

1.344 (34.138)

3051SFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 10.7 (4.58) 7.5 (3.70)

1-in. (25 mm) 11.45 (5. 1 9) 8.25 (4.07)

1

/2-in. (40 mm) 11.95 (5.42) 8.75 (4.32)

1 2-in. (50 mm) 12.20 (5.53) 9.00 (4.44) 3-in. (80 mm) 14.20 (6.44) 11.00 (5.43) 4-in. (100 mm) 16.70 (7.57) 13.50 (6.67) 5-in. (125 mm) 18.45 (8.37) 15.25 (7.53) 6-in. (150 mm) 20.20 (9.16) 17.00 (8.40) 8-in. (200 mm) 25.45 (11.54) 22.25 (10.99) 10-in (250 mm) 30.70 (13.92) 27.50 (13.58) 12-in (300 mm) 36.70 (16.64) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 3051S Coplanar PlantWeb housing transmitter.

(1)(2)

Remote Mount (R3)

3095MFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 9.50 (4.69) 6.3 (3.11)

1-in. (25 mm) 10.25 (5.06) 7.05 (3.48)

1

/2-in. (40 mm) 10.75 (5.31) 7.55 (3.73)

1 2-in. (50 mm) 11.00 (5.43) 7.80 (3.85) 3-in. (80 mm) 13.00 (6.42) 9.80 (4.84) 4-in. (100 mm) 15.50 (7.65) 12.30 (6.07) 5-in. (125 mm) 17.25 (8.52) 14.05 (6.94) 6-in. (150 mm) 19.00 (9.38) 15.80 (7.80) 8-in. (200 mm) 24.25 (11.98) 21.05 (10.40) 10-in (250 mm) 29.50 (14.57) 26.30 (12.9) 12-in (300 mm) 35.50 (17.53) 32.30 (15.95)

(1) Measurement in lb (kg).

(2) Includes 3095 MultiVariable transmitter.

(1)(2)

Remote Mount (R3)

405 Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 3.50 (1.73) 7.5 (3.70)

1-in. (25 mm) 4.25 (2.10) 8.25 (4.07)

1

/2-in. (40 mm) 4.75 (2.34) 8.75 (4.32)

1 2-in. (50 mm) 5.00 (2.47) 9.00 (4.44) 3-in. (80 mm) 7.00 (3.45) 11.00 (5.43) 4-in. (100 mm) 9.50 (4.69) 13.50 (6.67) 5-in. (125 mm) 11.25 (5.55) 15.25 (7.53) 6-in. (150 mm) 13.00 (6.41) 17.00 (8.40) 8-in. (200 mm) 18.25 (9.00) 22.25 (10.99) 10-in (250 mm) 23.50 (11.59) 27.50 (13.58) 12-in (300 mm) 29.50 (14.55) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 405 Direct Mount option D3.

(1)(2)

Remote Mount (R3)

(1)

9

Rosemount Compact Orifice

Upstream (inlet)

side of primary

3051SFCDP Compact Orifice

3051SFCDC

Conditioning

Orifice

30°

120°

30°

360°

FLOW

Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Installation Considerations

Straight Run Requirements

TABLE 6. 3051SFCC Straight Pipe Requirements

Beta 0.40 0.65

Reducer (1 line size) 2 2 Single 90° bend or tee 2 2 Two or more 90 ° bends in the same

plane Two or more 90° bends in different

plane

side of primary

Up to 10° of swirl 2 2

Upstream (inlet)

Butterfly valve (75% to 100% open) 2 N/A

Downstream (outlet) side of primary

TABLE 7. 3051SFCP Straight Pipe Requirements

Beta 0.40 0.65

(2)(3)

Downstream (outlet) side of primary

(1) Consult an Emerson Process Management representative if

(2) Recommended lengths represented in pipe diameters per

(3) Refer to ISO 5167 for recommended lengths when using flow

Reducer (1 line size) 5 12 Single 90° bend or tee 16 44 Two or more 90 ° bends

in the same plane Two or more 90° bends

in different plane Expander 12 28 Ball / Gate valve fully open 12 18

disturbance is not listed.

ISO 5167.

straighteners.

(1)

2 2

22

(1)(2)(3)

10 44

50 60

6 7

Flowmeter Orientation

Flowmeter orientation for both 3051SFC Conditioning Compact Orifice and standard Compact Orifice.

Gas (Horizontal)

Liquid and Steam (Horizontal)

50°

80°

Gas (Vertical)

Pipe Orientation

Pipe orientation for both 3051SFCC Compact Conditioning and standard 3051SFCP Compact Orifice.

Process

Orientation/ Flow Direction

Horizontal D/R D/R D/R Vertical Up R D/R R Vertical Down D/R NR NR

(1) D = Direct mount acceptable (recommended)

R = Remote mount acceptable NR = Not recommended

Gas Liquid Steam

(1)

Pipe Centering

Improper centering of any orifice type device can cause an error of up to ±5% in small line sizes. A centering mechanism (centering ring) independent of flange rating comes standard with the 405 Compact Orifice Series.

10

Liquid (Vertical)

360°

FLOW

Product Data Sheet

00813-0100-4810, Rev HA March 2008

PRODUCT CERTIFICATIONS

Approved Manufacturing Locations

Rosemount Inc. — Chanhassen, Minnesota USA

Emerson Process Management GmbH & Co. — Wessling, Germany

Emerson Process Management Asia Pacific Private Limited — Singapore

Beijing Rosemount Far East Instrument Co., LTD — Beijing, China

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can be found at www.rosemount.com. A hard copy may be obtained by contacting an Emerson Process Management representative.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

European Pressure Equipment Directive (PED) (97/23/EC)

Models 3051S_CA4; 3051S_CD2, 3, 4, 5; (also with P9 option) Pressure Transmitters — QS Certificate of Assessment EC No. PED-H-20, Module H Conformity Assessment

All other Model 3051S Pressure Transmitters — Sound Engineering Practice

Transmitter Attachments: Diaphragm Seal - Process Flange Manifold

Primary Elements, Flowmeter — See appropriate Primary Element QIG

— Sound Engineering Practice

Electro Magnetic Compatibility (EMC) (89/336/EEC)

All Models: EN 50081-1: 1992; EN 50082-2:1995; EN 61326-1:1997 – Industrial

Ordinary Location Certification for FM

As standard, the transmitter has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).

Hazardous Locations Certifications

North American Certifications

FM Approvals

E5 Explosion-proof for Class I, Division 1, Groups B, C, and D;

dust-ignition proof for Class II and Class III, Division 1, Groups E, F, and G; hazardous locations; enclosure Type 4X, conduit seal not required when installed according to Rosemount drawing 03151-1003.

Rosemount Compact Orifice

Flowmeter Series

I5/IE Intrinsically Safe for use in Class I, Division 1, Groups A, B,

C, and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1; Class I, Zone 0 AEx ia IIC when connected in accordance with Rosemount drawing 03151-1006; Non-incendive for Class I, Division 2, Groups A, B, C, and D Enclosure Type 4X For entity parameters see control drawing 03151-1006.

Canadian Standards Association (CSA)

E6 Explosion-proof for Class I, Division 1, Groups B, C, and D;

Dust-Ignition-Proof for Class II and Class III, Division 1, Groups E, F, and G; suitable for Class I, Division 2, Groups A, B, C, and D, when installed per Rosemount drawing 03151-1013, CSA Enclosure Type 4X; conduit seal not required.

I6/IF Intrinsically Safe for Class I, Division 1, Groups A, B, C, and

D when connected in accordance with Rosemount drawings 03151-1016; For entity parameters see control drawing 03151-1016.

European Certifications

I1/IA ATEX Intrinsic Safety

Certificate No.: BAS01ATEX1303X II 1G EEx ia IIC T4 (T Display/Quick Connect/HART Diagnostics EEx ia IIC T4 (T EEx ia IIC T4 (T IP66

118 0

TABLE 8. Input Parameters

Loop / Power Groups

U

= 30 V HART / FOUNDATION fieldbus/ Remote

i

Ui = 17.5 V FISCO I

= 300 mA HART / FOUNDATION fieldbus/ Remote

i

Ii = 380 mA FISCO P

= 1.0 W HART / Remote Display / Quick Connect /

i

Pi = 1.3 W FOUNDATION fieldbus P

= 5.32 W FISCO

i

Ci = 30 nF SuperModule Platform / Quick Connect C

= 11.4 nF HART / HART Diagnostics

i

Ci = 0 FOUNDATION fieldbus / Remote Display /

L

= 0 HART / FOUNDATION fieldbus/ FISCO /

i

Li = 60 µH Remote Display

Special conditions for safe use (x)

1. The apparatus, excluding the Types 3051 S-T and 3051 S-C (In-line and Coplanar SuperModules respectively), is not capable of withstanding the 500V test as defined in Clause 6.4.12 of EN 50020. This must be considered during installation.

2. The terminal pins of the Types 3051 S-T and 3051 S-C must be protected to IP20 minimum.

= -60 °C to 70 °C) -HART/Remote

a

= -60 °C to 70 °C) -FOUNDATION fieldbus

a

= -60 °C to 40 °C) -FISCO

a

Display / Quick Connect / HART Diagnostics

HART Diagnostics

FISCO

Quick Connect / HART Diagnostics

11

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

N1 ATEX Typ e n

Certificate No.: BAS01ATEX3304X II 3 G EEx nL IIC T4 (T Ui = 45 Vdc max IP66

Special conditions for safe use (x)

The apparatus is not capable of withstanding the 500V insulation test required by Clause 9.1 of EN 50021: 1999. This must be taken into account when installing the apparatus.

ND ATEX Dust

Certificate No.: BAS01ATEX1374X II 1 D T105°C (-20 °C ≤ T

= 42.4 volts max

V

max

A = 22 mA IP66

118 0

Special conditions for safe use (x)

1. The user must ensure that the maximum rated voltage and current (42.4 volts, 22 milliampere, DC) are not exceeded. All connections to other apparatus or associated apparatus shall have control over this voltage and current equivalent to a category “ib” circuit according to EN 50020.

2. Cable entries must be used which maintain the ingress protection of the enclosure to at least IP66.

3. Unused cable entries must be filled with suitable blanking plugs which maintain the ingress protection of the enclosure to at least IP66.

4. Cable entries and blanking plugs must be suitable for the ambient range of the apparatus and capable of withstanding a 7J impact test.

5. The 3051S must be securely screwed in place to maintain the ingress protection of the enclosure.

E1 ATEX Flameproof

Certificate No.: KEMA00ATEX2143X II 1/2 G EEx d IIC T6 (-50 °C ≤ T EEx d IIC T5 (-50 °C ≤ T

= 42.4V

V

max

118 0

Special conditions for safe use (x)

This device contains a thin wall diaphragm. Installation, maintenance and use shall take into account the environmental conditions to which the diaphragm will be subjected. The manufacturer’s instructions for installation and maintenance shall be followed in detail to assure safety during its expected lifetime. The Model 3051S pressure transmitter must include a Series 300S housing integrally mounted to a Series Model 3051S Sensor module as per Rosemount drawing 03151-1023.

= -40 °C TO 70 °C)

a

≤ 85 °C)

amb

≤ 65 °C)

amb

≤ 80 °C)

amb

Japanese Certifications

E4 TIIS Flameproof

Ex d IIC T6

Certificate Description

TC15682 Coplanar with Junction Box Housing TC15683 Coplanar with PlantWeb Housing TC15684 Coplanar with PlantWeb Housing

TC15685 In-Line SST with Junction Box Housing TC15686 In-Line Hastelloy with Junction Box Housing TC15687 In-Line SST with PlantWeb Housing TC15688 In-Line Hastelloy with Plantweb Housing TC15689 In-Line SST with Plantweb Housing

TC15690 In-Line Hastelloy with PlantWeb Housing

and LCD Display

Australian Certifications

E7 SAA Flameproof and Dust Ignition-proof

Certification No.: AUS Ex 3798X Ex d IIC T6 (T DIP A21 TA T6 (T

Special conditions for safe use (x)

1. It is a condition of safe use that each housing shall be connected to external circuits via suitable conduit or Standards Australia certified cable glands. Where only one entry is used for connection to external circuits, the unused entry shall be closed by means of the blanking plug supplied by the equipment manufacturer or by a suitable Standards Australia certified blanking plug.

2. It is a condition of safe use that a dielectric strength test shall be applied whenever the terminal block is changed or replaced in either the dual compartment or single compartment housings. The breakdown current shall be less than 5 mA, when 500 V, 47 to 62 Hz, is applied for one minute. Note: if tested with an optional T1 transient protector terminal block fitted, the protection will operate and hence there will be no current indicated.

3. It is a condition of safe use that each transmitter module shall be used with a Model 300S housing, in order to comply with flameproof requirements.

4. It is a condition of safe use that each model 300S housing fitted with a transmitter module shall be marked with the same certification marking code information. Should the housing be replaced after initial supply to another model 300S housing, the replacement housing shall have the same certification marking code information as the housing it replaces.

= 60°C) IP66

a

= 60°C) IP66

a

12

Product Data Sheet

µ

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

IECEx Certifications

I7/IG IECEx Intrinsic Safety

Certificate No.: IECExBAS04.0017X Ex ia IIC T4 (T Display/Quick Connect/HART Diagnostics Ex ia IIC T4 (T Ex ia IIC T4 (T IP66

TABLE 9. Input Parameters

Loop / Power Groups

U

= 30 V HART / FOUNDATION fieldbus/

i

Ui = 17.5 V FISCO I

= 300 mA HART / FOUNDATION fieldbus/

i

Ii = 380 mA FISCO P

= 1.0 W HART / Remote Display / Quick

i

Pi = 1.3 W FOUNDATION fieldbus P

= 5.32 W FISCO

i

Ci = 30 nF SuperModule Platform / Quick

C

= 11.4 nF HART / HART Diagnostics

i

Ci = 0 FOUNDATION fieldbus / Remote

= 0 HART / FOUNDATION fieldbus /

L

i

Li = 60 H Remote Display

Special conditions for safe use (x)

1. The Models 3051S HART 4-20mA, 3051S fieldbus, 3051S Profibus and 3051S FISCO are not capable of withstanding the 500V test as defined in clause 6.4.12 of IEC 60079-11. This must be taken into account during installation.

2. The terminal pins of the Types 3051S-T and 3051S-C must be protected to IP20 minimum.

= -60 °C to 70 °C) -HART/Remote

a

= -60 °C to 70 °C) -FOUNDATION fieldbus

a

= -60 °C to 40 °C) -FISCO

a

Remote Display / Quick Connect / HART Diagnostics

Connect / HART Diagnostics

Connect

Display / FISCO / Quick Connect / HART Diagnostics

FISCO / Quick Connect / HART Diagnostics

N7 IECEx Type n

Certificate No.: IECExBAS04.0018X Ex nC IIC T4 (Ta = -40 °C to 70 °C) Ui = 45 Vdc MAX IP66

Special conditions for safe use (x)

The apparatus is not capable of withstanding the 500 V insulation test required by Clause 8 of IEC 79-15: 1987.

Combinations of Certifications

Stainless steel certification tag is provided when optional approval is specified. Once a device labeled with multiple approval types is installed, it should not be reinstalled using any other approval types. Permanently mark the approval label to distinguish it from unused approval types.

K1 Combination of E1, I1, N1, and ND

K5 Combination of E5 and I5

K6 Combination of E6 and I6

K7 Combination of E7, I7, and N7

KA Combination of E1, I1, E6, and I6

KB Combination of E5, I5, I6 and E6

KC Combination of E5, E1, I5 and I1

KD Combination of E5, I5, E6, I6, E1, and I1

13

Rosemount Compact Orifice

Radio Power Label

Figure 1.

Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

WIRELESS CERTIFICATIONS

Telecommunication Compliance

All wireless devices require certification to ensure that they adhere to regulations regarding the use of the RF spectrum. Nearly every country requires this type of product certification. Emerson is working with governmental agencies around the world to supply fully compliant products and remove the risk of violating country directives or laws governing wireless device usage.

FCC and IC Approvals

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: This device may not cause harmful interference this device must accept any interference received, including interference that may cause undesired operation.

This device must be installed to ensure a minimum antenna separation distance of 20cm from all persons.

Ordinary Location Certification for FM

As standard, the transmitter has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can be found at www.rosemount.com. A hard copy may be obtained by contacting an Emerson Process Management representative.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

European Pressure Equipment Directive (PED) (97/23/EC)

Models 3051S_CA4; 3051S_CD2, 3, 4, 5; (also with P9 option) Pressure Transmitters — QS Certificate of Assessment EC No. PED-H-100, Module H Conformity Assessment

All other Model 3051S Pressure Transmitters — Sound Engineering Practice

Transmitter Attachments: Diaphragm Seal - Process Flange Manifold

Primary Elements, Flowmeter — See appropriate Primary Element QIG

Electro Magnetic Compatibility (EMC) (2004/108/EC)

All Models: EN 50081-1: 1992; EN 50082-2:1995; EN 61326-1:1997 + A1, A2, and A3 – Industrial

Radio and Telecommunications Terminal Equipment Directive (R&TTE)(1999/5/EC)

Emerson Process Management complies with the R&TTE Directive.

— Sound Engineering Practice

Hazardous Locations Certifications

North American Certifications

Factory Mutual (FM) Approvals

I5 FM Intrinsically Safe, Non-Incendive, and Dust Ignition-proof.

Intrinsically Safe for Class I/II/III, Division 1, Groups A, B, C, D, E, F, and G. Zone Marking: Class I, Zone 0, AEx ia llC Temperature Codes T4 (T Non-Incendive for Class I, Division 2, Groups A, B, C, and D. Dust Ignition-proof for Class II/III, Division 1, Groups E, F, and G. Ambient temperature limits: -50 to 85° C For use with Rosemount SmartPower options 00753-9220-XXXX only. Enclosure Type 4X / IP66

CSA - Canadian Standards Association

I6 CSA Intrinsically Safe

Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D. Temp Code T3C Enclosure Type 4X / IP66 For use with Rosemount SmartPower options 00753-9220-XXXX only.

European Certifications

I1 ATEX Intrinsic Safety

Certificate No.: BAS01ATEX1303X II 1G Ex ia IIC T4 (T IP66 For use with Rosemount SmartPower options 00753-9220-XXXX only.

1180

Country Restriction

Bulgaria General authorization required for outdoor use

France Outdoor use limited to 10mW e.i.r.p. Italy If used outside of own premises, general

Norway May be restricted in the geographical area within

Romania Use on a secondary basis. Individual license

Radio Power Label (See Figure 1) indicates output power configuration of the radio. Devices with this label are configured for output power less than 10 mW e.i.r.p. At time of purchase the customer must specify ultimate country of installation and operation.

= -60 °C to 70 °C)

a

and public service

authorization is required.

a radius of 20 km from the center of Ny-Alesund.

required.

= -50 to 70° C)

amb

14

IECEx Certifications

I7 IECEx Intrinsic Safety

Certificate No.: IECEx BAS 04.0017X Ex ia IIC T4 (Ta = -60 °C to 70 °C) For use with Rosemount SmartPower options 00753-9220-XXXX only. IP66

Product Data Sheet

1.13 (28.7)

1.00 (25.4

C

A

B

1.13 (28.7)

1.00 (25.4

C

00813-0100-4810, Rev HA March 2008

DIMENSIONAL DRAWINGS

Rosemount 3051SFC Compact Orifice Flowmeter

Orifice Plate Front View Orifice Plate Side View Orifice Plate Top View

B

A

Compact Orifice Plate

(Primary Element Type code P)

Rosemount Compact Orifice

Flowmeter Series

D

(Primary Element Type code C)

Conditioning Orifice Plate

TABLE 10. Dimensional Drawings

Plate Type A B Transmitter Height C D

Type P and C 5.50 (140) Transmitter Height + A 7.75 (197) 7.75 (197) - closed

(1) Measurement in inches (millimeters).

(1)

8.25 (210) - open

6.00 (152) - closed

6.25 (159) - open

15

Rosemount Compact Orifice Flowmeter Series

ORDERING INFORMATION

Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information

Model Product Description

3051SFC Compact Orifice Flowmeter

Code Measurement Type

D Differential Pressure

Code Primary Element Type

C Conditioning Orifice Plate P Orifice Plate

Code Material Type

S 316 Stainless Steel (SST)

(1)

H

Code Line Size

(2) 1

005

(2)

010

(2)

015 020 2-in. (50 mm) 030 3-in. (80 mm) 040 4-in. (100 mm)

(1)

050 060 6-in. (150 mm) 080 8-in. (200 mm)

(1)

100

(1)

120

Code Primary Element Style

N Square Edged

Code Beta Ratio

040 0.40 Beta Ratio (β)

(3)

065

Code Temperature Measurement

R Remote Thermowell and RTD

(1)

T 0 No Temperature Sensor

Code Transmitter Connection Platform

3 Direct-mount, 3-valve integral manifold, SST 7 Remote-mount, 1/4-in. NPT connections

Code Differential Pressure Range

1 0 to 25 in H2O (0 to 62.2 mbar) 2 0 to 250 in H2O (0 to 623 mbar) 3 0 to 1000 in H2O (0 to 2.5 bar)

Code Static Pressure Range

A None

Code Output Protocol

A 4–20 mA with digital signal based on HART protocol

(4)

F

(5)

X

Hastelloy

/2-in. (15 mm) 1-in. (25 mm) 11/2-in. (40 mm)

5-in. (125 mm)

10-in (250 mm) 12-in. (300 mm)

0.65 Beta Ratio (β)

Integral RTD and Thermowell

FOUNDATION fieldbus protocol Wireless (Requires wireless options and wireless housing 5A)

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

16

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information

Code Transmitter Housing Style Material Conduit Entry Size

00 None (Customer-supplied electrical connection) 01 Assemble to Rosemount 753R Web-based Monitoring Indicator 1A PlantWeb Housing Aluminum 1B PlantWeb Housing Aluminum M20 x 1.5 (CM20) 1C PlantWeb Housing Aluminum G 1J PlantWeb Housing 316L SST 1K PlantWeb Housing 316L SST M20 x 1.5 (CM20) 1L PlantWeb Housing 316L SST G1/2 2A Junction Box Housing Aluminum 2B Junction Box Housing Aluminum M20 x 1.5 (CM20) 2C Junction Box Housing Aluminum G 2E Junction Box housing with output for remote display and interface Aluminum 2F Junction Box housing with output for remote display and interface Aluminum M20 x 1.5 (CM20) 2G Junction Box housing with output for remote display and interface Aluminum G1/2 2J Junction Box Housing 316L SST 2M Junction Box housing with output for remote display and interface 316L SST 5A Wireless PlantWeb housing Aluminum M20 x 1.5 (CM20)

(6)

7J

Code Transmitter Performance Class for Flow

(7)

1 2 Classic: up to ± 1.05% flow rate accuracy, 8:1 flow turndown, 5-year stability

(7)

3

Code Options

Installation Accessories

G DIN Alignment Ring (PN 16) H DIN Alignment Ring (PN 40, PN 100) B JIS Alignment Ring 10K R JIS Alignment Ring 20K S JIS Alignment Ring 40K

Remote Adapters

E Flange adapters 316 SST (1/2-in. NPT)

High Temperature Applications

T Graphite valve packing (Tmax = 850 °F)

Flow Calibration

(8)

WC

(8)

WD

Pressure Testing

P1 Hydrostatic testing with certificate

Special Cleaning

P2 Cleaning for special processes PA Cleaning per ASTM G93 Level D (section 11.4)

Special Inspection

QC1 Visual and dimensional inspection with certificate QC7 Inspection and performance certificate

Transmitter Calibration Certification

Q4 Calibration Data Certificate for Transmitter QP Calibration Data Certificate and Tamper Evident Seal

Safety Certification

QS Certificate of FMEDA data

(9)

QT

Material Traceability Certifications

(10)

Q8

Quick Connect (A size Mini, 4-pin male termination)

Ultra: up to ± 0.85% flow rate accuracy, 8:1 flow turndown, 10-year stability, limited 12-year warranty

Ultra for Flow: up to ± 0.75% flow rate accuracy, 14:1 flow turndown, 10-year stability. limited 12-year warranty

Discharge coefficient verification (3 point) Discharge coefficient verification (10 point)

Safety Certified to IEC 61508 with certificate of FMEDA data

Material Cert per ISO 10474 3.1.B and EN 10204 3.1.B

1

/2-14 NPT

1

/2

1

/2-14 NPT

1

/2-14 NPT

1

/2

1

/2-14 NPT

1

/2-14 NPT

1

/2-14 NPT

17

Rosemount Compact Orifice

Product Data Sheet

00813-0100-4810, Rev HA

Flowmeter Series

Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information

Code Conformance

J2 ANSI B31.1 J3 ANSI B31.3 J4 ANSI B31.8

Material Conformance

(11)

J5

Country Certification

J1 Canadian Registration

Product Certifications

E1 ATEX Flameproof I1 ATEX Intrinsic Safety IE FM FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only IF CSA FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only

(1)

IA N1 ATEX Type n ND ATEX Dust K1 ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E1, I1, N1, and ND) E4 TIIS Flameproof E5 FM Explosion-proof, Dust Ignition-proof I5 FM Intrinsically Safe, Division 2 K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5) E6 CSA Explosion-proof, Dust Ignition-proof, Division 2 I6 CSA Intrinsically Safe K6 CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E6 and I6)

(1)

E7 I7 IECEx Intrinsic Safety IG IECEx FISCO Intrinsic Safety; for FOUNDATION fieldbus protocol only N7 IECEx Type n K7 SAA Flameproof, Dust Ignition-proof, IECEx Intrinsic Safety, Type n (combination of E7, I7, and N7) KA ATEX and CSA Flameproof, Intrinsically Safe, Division 2 (combination of E1, I1, E6, and I6)

KB FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5, E6, I5, and I6)

KC FM and ATEX Explosion-proof, Intrinsically Safe, Division 2 (combination of E5, E1, I5, and I1)

KD FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of E5, I5, E6, I6, E1, and I1)

Alternative Transmitter Material of Construction

L1 Inert Sensor Fill Fluid L2 Graphite-filled PTFE o-ring LA Inert sensor fill fluid and graphite-filled PTFE o-ring

Display

M5 PlantWeb LCD display

(7)(13)

M7

(7)(13)

M8

(7)(13)

M9

Terminal Blocks

(14)

T1

(15)

T2

(15)

T3

Manifold for Remote Mount Option

F2 3-Valve Manifold, SST F6 5-Valve Manifold, SST

PlantWeb Control Functionality

(16)

A01

PlantWeb Diagnostic Functionality

(16)

D01

(17)

DA1

NACE MR-0175 / ISO 15156

ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus protocol only

SAA Flameproof, Dust Ignition-proof

Note: Only available on Housing Style codes 00, 1A, 1J, 2A, 2J, 2E, or 2M.

(12)

Remote mount LCD display and interface, no cable; PlantWeb housing, SST bracket, requires 4-20 mA / HART output Remote mount LCD display and interface, 50 ft. (15 m) cable; PlantWeb housing, SST bracket, requires 4-20 mA / HART output Remote mount LCD display and interface, 100 ft. (31 m) cable; PlantWeb housing, SST bracket, requires 4-20 mA / Hart output

Transient terminal block Terminal block with WAGO spring clamp terminals Transient terminal block with WAGO spring clamp terminals

FOUNDATION fieldbus Advanced Control Function Block Suite

FOUNDATION fieldbus Diagnostics Suite HART Diagnostic Suite

March 2008

18

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

Rosemount 3051SFC Compact Orifice Flowmeter Ordering Information

PlantWeb Enhanced Measurement Functionality

(16)(18)

H01

Code Wireless Options - Select code from each wireless category (example: WA2WK1)

Wireless Transmit Rate

WA User Configurable Transmit Rate

Operating Frequency and Protocol

1 2.4 GHz DSSS, HART 2 900 MHz FHSS, HART

Antenna

WK Omnidirectional, Integral Antenna

SmartPower

1 Long-life Power Module Adapter, Intrinsically Safe

Code Options

Special Configuration (Software)

(7)(19)

C4

(7)(19)

C5

(7)(19)

C6

(7)(19)

C7

(7)(19)

C8

Special Configuration (Hardware)

(7)(19)

D1 D4 External ground screw

(7)(19)

DA

Conduit Electrical Connector

(20)

ZE

(20)

ZM

(1) Consult factory for availability.

(2) Not available for Primary Element Type code C.

(3) For 2-in. (50.8 mm) line sizes the Beta Ratio is 0.6 for Primary Element Type code C.

(4) Requires PlantWeb housing.

(5) Available approvals are FM Intrinsically Safe, Division 2 (option code I5), CSA Intrinsically Safe (option code I6), ATEX Intrinsic Safety

(option code I1; only available with 2.4 GHz), and IECEx Intrinsic Safety (option code I7; only available with 2.4 GHz).

(6) Available with output code A only. Available approvals are FM Intrinsically Safe, Division 2 (option code I5) or ATEX Intrinsic Safety (option code I1). Contact

an Emerson Process Management representative for additional information.

(7) Not available with Output Protocol code X.

(8) Not available with Primary Element Type code P.

(9) Not available with output code F or X. Not available with housing code 01 or 7J.

(10) Instrument valves not included in Traceability Certification.

(11) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits

apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.

(12) Not available with Housing code 01 or 7J.

(13) Not available with output code F, Housing code 01, option code DA1, or option code QT.

(14) Not available with Housing code 00, 01, 5A, or 7J.

(15) Available with Output Protocol code A and Plantweb housing only.

(16) Requires PlantWeb housing and output code F.

(17) Requires PlantWeb housing and output code A. Includes Hardware Adjustments as standard. Not available with option code QT.

(18) Requires Rosemount Engineering Assistant to configure.

(19) Not available for Output Protocol code F or Housing code 01.

(20) Not available with Housing code 00, 01, 5A, or 7J. Available with Intrinsically Safe approvals only. For FM Intrinsically Safe, Division 2

(option code I5) or FM FISCO Intrinsically Safe (option code IE), install in accordance with Rosemount drawing 03151-1009 to maintain outdoor rating (NEMA 4X and IP66).

Fully Compensated Mass Flow Block

™

NOTE: Long-life Power Module must be shipped separately, order Part No. 00753-9220-0001.

NAMUR alarm and saturation signal levels, high alarm NAMUR alarm and saturation signal levels, low alarm Custom alarm and saturation signal levels, high alarm

Note: A Configuration Data Sheet must be completed, see document number 00806-0100-4810.

Custom alarm and saturation signal levels, low alarm

Note: A Configuration Data Sheet must be completed, see document number 00806-0100-4810.

Low alarm (standard Rosemount alarm and saturation signal levels)

Hardware Adjustment (zero, span, alarm, security).

Hardware adjustment (zero, span, alarm, security) and external ground screw

M12, 4-pin, Male Connector (eurofast®) A size Mini, 4-pin, Male Connector (minifast®)

19

Rosemount Compact Orifice

Product Data Sheet

00813-0100-4810, Rev HA

Flowmeter Series

March 2008

Rosemount 3095MFC Compact Orifice Mass Flowmeter

SPECIFICATIONS

Performance

System Reference Accuracy

Percent (%) of mass flow rate

TABLE 11. 3095MFC Compact Orifice Mass Flowmeter

Mass flow

TYPE BETA

3095MFCC 0.4 ±0.90% ±0.70%

3095MFCP

(1) Line sizes 1/2-in. (15mm)

(2) Line sizes 1-in. to 1 1/2-in. (25 mm to 40 mm)

(3) Line sizes 2-in. to 12-in. (50 mm to 300 mm)

(4) For 0.65 beta and ReD< 10,000 add an additional ±0.5% to the

(1)

(2)

(3)

Discharge Coefficient Uncertainty.

0.65 ±1.30% ±1.15%

0.4

(4)

0.65

0.4

(4)

0.65

0.4

(4)

0.65

(8:1 flow

turndown)

±2.50% ±2.45%

±2.10% ±2.00%

±1.50% ±1.40%

Repeatability

±0.1%

Line Sizes

•1/2-in. (15 mm) – not available for the 3095MFCC

• 1-in. (25 mm) – not available for the 3095MFCC

1

/2-in. (40 mm) – not available for the 3095MFCC

•1

• 2-in. (50 mm)

• 3-in. (80 mm)

• 4-in. (100 mm)

• 5-in (125 mm)

• 6-in. (150 mm)

• 8-in. (200 mm)

• 10-in. (250 mm)

• 12-in (300 mm)

Output

Two-wire 4–20 mA, user-selectable for DP, AP, GP, PT, mass flow, or totalized flow. Digital HART protocol superimposed on 4–20 mA signal, available to any host that conforms to the HART protocol.

Performance Statement Assumptions

• Measured pipe I.D

• Electronics are trimmed for optimum flow accuracy

Ultra for Flow

(10:1 flow turndown)

Functional

Service

• Liquid

•Gas

•Steam

Power Supply

4–20 mA option

• External power supply required. Standard transmitter (4–20 mA) operates on 11 to 55 v dc with no load

Process Temperature Limits

Direct Mount Transmitter

• 450 °F (232 °C)

Remote Mount Transmitter

• 850 °F (454 °C) – Stainless Steel

Transmitter Temperature Limits

Ambient

• -40 to 185 °F (-40 to 85 °C)

• with integral display: -4 to 175 °F (-20 to 80 °C)

Storage

• -50 to 230 °F (-46 to 110 °C)

• with integral display: -40 to 185 °F (-40 to 85 °C)

Differential Pressure Limits

Maximum differential pressure (DP) up to 800 inH2O.

Pressure Limits

Direct Mount Transmitter

• Pressure retention per ANSI B16.5 600# or DIN PN 100

Overpressure Limits

0 to 2 times the absolute pressure range with a maximum of 3626 psia (250 bar).

Static Pressure Limits

Operates within specification between static pressures of 0.5 psia (0.03 bar-A) and the URL of the static pressure sensor.

Vibration Limits

Qualified per IEC61298-3 (1998) for field with high vibration level or pipeline with high vibration level (10-60Hz 0.21mm displacement peak amplitude / 60 - 500Hz 3g).

The weight and length of the transmitter assembly shall not exceed 5.8 lbs and 7.75-in.

(1)

Sizing

Contact an Emerson Process Management representative for assistance. A Configuration Data Sheet is required prior to order for application verification.

20

(1) Static pressure selection may effect pressure limitations.

Product Data Sheet

Load (Ohms)

0

11.0 42.4

(1)

55

Operating

Region

(1) For CSA approval, power supply must not exceed 42.4 V dc.

(2) HART protocol communication requires a loop resistance value

between 250-1100 ohms, inclusive.

Power Supply

250

16.5

(2)

Maximum Loop Resistance = Power Supply - 11.0

0.022

2000

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Load Limitations

Maximum loop resistance is determined by the voltage level of the external power supply, as described by:

FOUNDATION fieldbus (output option code V)

Power Supply

External power supply required; transmitters operate on 9.0 to

32.0 V dc transmitter terminal voltage.

Current Draw

17.5 mA for all configurations (including LCD display option)

Humidity Limits

• 0–100% relative humidity

Turn-On Time

Digital and analog measured variables will be within specification 7 – 10 seconds after power is applied to the transmitter.

Digital and analog flow output will be within specifications 10 – 14 seconds after power is applied to the transmitter.

Damping

Analog output response to a step input change is user-selectable from 0 to 29 seconds for one time constant. This software damping is in addition to sensor module response time

Failure Mode Alarm

Output Code A

If self-diagnostics detect a non-recoverable transmitter failure, the analog signal will be driven either below 3.75 mA or above

21.75 mA to alert the user. High or low alarm signal is user-selectable by internal jumper pins.

Output Code V

If self-diagnostics detect a gross transmitter failure, that information gets passed as a status along with the process variable(s).

Configuration

HART Hand-held Communicator (Model 275 or 375)

• Performs traditional transmitter maintenance functions

3095 Multivariable Engineering Assistant (EA) software package

• Contains built-in physical property database

• Enables mass flow configuration, maintenance, and diagnostic functions via HART modem (output option code A)

Enables mass flow configuration via PCMCIA Interface for F

OUNDATION fieldbus (output option code V)

Physical Properties Database

• Maintained in Engineering Assistant Software Configurator

• Physical properties for over 110 fluids

• Natural gas per AGA

• Steam and water per ASME

• Other database fluids per American Institute of Chemical Engineers (AIChE)

• Optional custom entry

FOUNDATION fieldbus Function Blocks

Standard Function Blocks

Resource Block

• Contains hardware, electronics, and diagnostic information.

Transducer Block

• Contains actual sensor measurement data including the sensor diagnostics and the ability to trim the pressure sensor or recall factory defaults.

LCD Block

• Configures the local display.

5 Analog Input Blocks

• Processes the measurements for input into other function

blocks. The output value is in engineering or custom units and contains a status indicating measurement quality.

PID Block with Auto-tune

• Contains all logic to perform PID control in the field including

cascade and feedforward. Auto-tune capability allows for superior tuning for optimized control performance.

Advanced Control Function Block Suite (Option Code A01)

Input Selector Block

• Selects between inputs and generates an output using specific selection strategies such as minimum, maximum, midpoint, average, or first “good.”

Arithmetic Block

• Provides pre-defined application-based equations including flow with partial density compensation, electronic remote seals, hydrostatic tank gauging, ratio control and others.

Signal Characterizer Block

• Characterizes or approximates any function that defines an input/output relationship by configuring up to twenty X, Y coordinates. The block interpolates an output value for a given input value using the curve defined by the configured coordinates.

Integrator Bock

• Compares the integrated or accumulated value from one or two variables to pre-trip and trip limits and generates discrete output signals when the limits are reached. This block is useful for calculating total flow, total mass, or volume over time.

Output Splitter Block

• Splits the output of one PID or other control block so that the PID will control two valves or other actuators.

Control Selector Block

• Selects one of up to three inputs (highest, middle, or lowest) that are normally connected to the outputs of PID or other control function blocks.

21

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Physical

Temperature Measurement

Remote RTD

• 100 Ohm platinum with series with Rosemount 644 housing) Model 0078D21N00A025T32Ex Connection Head: 00644-4410-0011

• Standard RTD cable is shielded armored cable, length is 12 feet (3.66 m)

• Remote RTD material is SST

Thermowell

1

/2-in. x 1/2-in. NPT, 316 SST

•

NOTE

Remote temperature measurement is not available for and 11/2-in. sizes.

Electronic Connections for Remote Mount

•1/2–14 NPT, G1/2, and M20 × 1.5 (CM20) conduit. HART interface connections fixed to terminal block for output code A

Process-Wetted Parts

Integral Manifolds

•316 SST

• Hastelloy C-276

Remote Manifolds

•316 SST

• Hastelloy C-276

Transmitter Vent Valves and Process Flanges

•316 SST

• Hastelloy C-276

• Glass-filled PTFE O-rings

Process Isolating Diaphragms

•316L SST

• Hastelloy C-276

Integral Manifold O-Rings

• PTFE/Graphite

Non-Wetted Parts

Sensor Module Fill Fluid

• Silicone oil

• Inert Fill optional

Cover O-rings

• Buna-N

Remote Mounting Brackets

•SST

Electronic Housing

• Low copper aluminum, NEMA 4x, IP65

• SST (optional)

Paint

• Polyurethane

Bolts

•CS

(1)

1

/2-in. NPT nipple and union (078

1

/2-in., 1-in.,

Material of Construction

Body/Plate

•316 SST

• 50 micro-inch Ra surface finish

Manifold Head/Valves

•316 SST

Flange Studs and Nuts

• Customer supplied

• Available as a spare part

Transmitter Connection Studs and Nuts

• Studs– A193 Grade B8M.

• Nuts– A194 Grade 8M.

Gasket and O-rings

• Gaskets are customer supplied.

• Durlon 8500 fiber gaskets are recommended. Consult an Emerson Process Management representative for use with other gaskets.

• Available as a spare part

NOTE

Gaskets and O-rings should be replaced when the 405 is disassembled.

Transmitter Connections

Remote Mount

• Available with connections

Orifice Type

• Square edged, Wafer style

Orifice Pressure Taps

• Corner

1

/4-in. (standard) or 1/2-in. (option code E)

Process Connections

Mounts between the following flange configurations

ASME B16.5 (ANSI)

Class 150

Class 300

Class 600

ANSI alignment ring is included as standard when ordering

DIN JIS

PN16 (option code G)

PN40 (option code H)

PN100 (option code H)

10k (option code B)

20k (option code R)

40k (option code S)

22

(1)

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Typical Orifice Hole Sizes (For 3095MFCC)

Beta is calculated by: (β) = dC / Pipe ID, where the calculated bore is equal to 2 x typical orifice hole size (d shows the diameter of each of the four typical orifice holes.

TABLE 12. β = 0.4

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.249 (6.325)

1-in. (25 mm) Not Available 0.420 (10.668)

1

/2-in. (40 mm) Not Available 0.644 (16.358)

1 2-in. (50 mm) 0.413 (10.490) 0.827 (21.006) 3-in. (80 mm) 0.614 (15.596) 1.227 (31.166) 4-in. (100 mm) 0.805 (20.447) 1.610 (40.894) 5-in. (125 mm) 1.009 (25.629) 2.019 (51.283) 6-in. (150 mm) 1.213 (30.810) 2.426 (61.620) 8-in. (200 mm) 1.596 (40.538) 3.192 (81.077) 10-in. (250 mm) 2.004 (50.902) 4.008 (101.80) 12-in. (300 mm) 2.400 (60.960) 4.800 (121.92)

TABLE 13. β = 0.65

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.404 (10.262)

1-in. (25 mm) Not Available 0.682 (17.323)

1

/2-in. (40 mm) Not Available 1.047 (26.594)

1 2-in. (50 mm) 0.620 (15.748) 3-in. (80 mm) 0.997 (25.324) 1.994 (50.648) 4-in. (100 mm) 1.308 (33.223) 2.617 (66.472) 5-in. (125 mm) 1.640 (40.640) 3.281 (83.34) 6-in. (150 mm) 1.971 (50.063) 3.942 (100.127) 8-in. (200 mm) 2.594 (65.888) 5.188 (131.775) 10-in. (250 mm) 3.257 (82.728) 6.513 (165.43) 12-in. (300 mm) 3.900 (99.060) 7.800 (198.120)

(1) Measurement is in inches (millimeters)

(2) Tolerance = ±0.002-in.

(3) Beta (β) = 0.60-in. (15.24 mm) for 2-in. line size only.

= 2d). The table below

C

(3)

1.344 (34.138)

3051SFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 10.7 (4.58) 7.5 (3.70)

1-in. (25 mm) 11.45 (5. 19) 8.25 (4.07)

1

/2-in. (40 mm) 11.95 (5.42) 8.75 (4.32)

1 2-in. (50 mm) 12.20 (5.53) 9.00 (4.44) 3-in. (80 mm) 14.20 (6.44) 11.00 (5.43) 4-in. (100 mm) 16.70 (7.57) 13.50 (6.67) 5-in. (125 mm) 18.45 (8.37) 15.25 (7.53) 6-in. (150 mm) 20.20 (9.16) 17.00 (8.40) 8-in. (200 mm) 25.45 (11.54) 22.25 (10.99) 10-in (250 mm) 30.70 (13.92) 27.50 (13.58) 12-in (300 mm) 36.70 (16.64) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 3051S Coplanar PlantWeb housing transmitter.

(1)(2)

Remote Mount (R3)

3095MFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 9.50 (4.69) 6.3 (3.11)

1-in. (25 mm) 10.25 (5.06) 7.05 (3.48)

1

/2-in. (40 mm) 10.75 (5.31) 7.55 (3.73)

1 2-in. (50 mm) 11.00 (5.43) 7.80 (3.85) 3-in. (80 mm) 13.00 (6.42) 9.80 (4.84) 4-in. (100 mm) 15.50 (7.65) 12.30 (6.07) 5-in. (125 mm) 17.25 (8.52) 14.05 (6.94) 6-in. (150 mm) 19.00 (9.38) 15.80 (7.80) 8-in. (200 mm) 24.25 (11.98) 21.05 (10.40) 10-in (250 mm) 29.50 (14.57) 26.30 (12.9) 12-in (300 mm) 35.50 (17.53) 32.30 (15.95)

(1) Measurement in lb (kg).

(2) Includes 3095 MultiVariable transmitter.

(1)(2)

Remote Mount (R3)

405 Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 3.50 (1.73) 7.5 (3.70)

1-in. (25 mm) 4.25 (2.10) 8.25 (4.07)

1

/2-in. (40 mm) 4.75 (2.34) 8.75 (4.32)

1 2-in. (50 mm) 5.00 (2.47) 9.00 (4.44) 3-in. (80 mm) 7.00 (3.45) 11.00 (5.43) 4-in. (100 mm) 9.50 (4.69) 13.50 (6.67) 5-in. (125 mm) 11.25 (5.55) 15.25 (7.53) 6-in. (150 mm) 13.00 (6.41) 17.00 (8.40) 8-in. (200 mm) 18.25 (9.00) 22.25 (10.99) 10-in (250 mm) 23.50 (11.59) 27.50 (13.58) 12-in (300 mm) 29.50 (14.55) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 405 Direct Mount option D3.

(1)(2)

Remote Mount (R3)

(1)

23

Rosemount Compact Orifice

Upstream (inlet)

side of primary

3095MFCDP

Compact Orifice

3095MFCDC

Conditioning Orifice

Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Installation Considerations

Straight Run Requirements

TABLE 14. 3095MFCC Straight Pipe Requirements

Beta 0.40 0.65

Reducer (1 line size) 2 2 Single 90° bend or tee 2 2 Two or more 90 ° bends in the same

plane Two or more 90° bends in different

plane

side of primary

Up to 10° of swirl 2 2

Upstream (inlet)

Butterfly valve (75% to 100% open) 2 N/A

Downstream (outlet) side of primary

TABLE 15. 3095MFCP Straight Pipe Requirements

Beta 0.40 0.65

(2)(3)

Downstream (outlet) side of primary

(1) Consult an Emerson Process Management representative if

(2) Recommended lengths represented in pipe diameters per ISO

(3) Refer to ISO 5167 for recommended lengths when using flow

Reducer 5 12 Single 90° bend or tee 16 44 Two or more 90 ° bends

in the same plane Two or more 90° bends in different

plane Expander 12 28 Ball / Gate valve fully open 12 18

disturbance is not listed.

5167.

straighteners.

(1)

2 2

22

(1)(2)(3)

10 44

50 60

6 7

Pipe Centering

Improper centering of any orifice type device can cause an error of up to ±5% in small line sizes. A centering mechanism (centering ring) independent of flange rating comes standard with the 405 Compact Orifice Series.

Pipe Orientation

Pipe orientation for both 3095MFCC Compact Conditioning Mass Orifice and standard 3095MFCP Compact Mass Orifice.

Horizontal D/R D/R D/R Vertical Up R D/R R Vertical Down D/R NR NR

24

Orientation/ Flow Direction

(1) D = Direct mount acceptable (recommended)

R = Remote mount acceptable NR = Not recommended

Gas Liquid Steam

Process

(1)

Product Data Sheet

30°

120°

30°

360°

FLOW

360°

FLOW

00813-0100-4810, Rev HA March 2008

Flowmeter Orientation

Flowmeter orientation for both 3095MFC Conditioning Compact Orifice and standard Compact Orifice.

Gas (Horizontal)

Liquid and Steam (Horizontal)

Rosemount Compact Orifice

Flowmeter Series

50°

80°

Gas (Vertical)

Liquid (Vertical)

25

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

PRODUCT CERTIFICATIONS

Rosemount 3095 with HART

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can be found on the Rosemount website at www.rosemount.com. A hard copy may be obtained by contacting our local sales office.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

European Pressure Equipment Directive (PED) (97/23/EC)

3095M_2/3,4/D Flow Transmitters — QS Certificate of Assessment - EC No. PED-H-20 Module H Conformity Assessment

All other 3095_ Transmitters/Level Controller — Sound Engineering Practice

Transmitter Attachments: Process Flange - Manifold — Sound Engineering Practice

Electro Magnetic Compatibility (EMC) (89/336/EEC)

3095MV Flow Transmitters

— EN 50081-1: 1992; EN 50082-2:1995;

EN 61326-1:1997 – Industrial

Ordinary Location Certification for Factory Mutual

As standard, the transmitter has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).

Hazardous Locations Certifications

North American Certifications

FM Approvals

E5 Explosion Proof for Class I, Division 1, Groups B, C, and D.

Dust-Ignition Proof for Class II/Class III, Division 1, Groups E, F, and G. Enclosure type NEMA 4X. Factory Sealed. Provides nonincendive RTD connections for Class I, Division 2, Groups A, B, C, and D.

I5 Intrinsically Safe for use in Class I, II and III, Division 1,

Groups A, B, C, D, E, F, and G hazardous outdoor locations. Non-incendive for Class I, Division 2, Gro ups A, B, C, and D. Temperature Code T4. Factory Sealed.

For input parameters and installation see control drawing 03095-1020.

Canadian Standards Association (CSA)

E6 Explosion Proof for Class I, Division 1, Groups B, C, and D.

Dust-Ignition Proof for Class II/Class III, Division 1, Groups E, F, and G. CSA enclosure Type 4X suitable for indoor and outdoor hazardous locations. Provides nonincendive RTD connection for Class I, Division 2, Groups A, B, C, and D.Factory Sealed. Install in accordance with Rosemount Drawing 03095-1024. Approved for Class I, Division 2, Groups A, B, C, and D.

I6 Intrinsically Safe for Class I, Division 1, Groups A, B, C, and

D. when installed in accordance with Rosemount drawing 03095-1021. Temperature Code T3C.

For input parameters and installation see control drawing 03095-1021.

European Certifications

I1 ATEX Intrinsic Safety

Certificate Number: BAS98ATEX1359X II 1 G

EEx ia IIC T5 (T EEx ia IIC T4 (T

118 0

TABLE 16. Connection Parameters (Power/Signal Te rm i na l s)

= 30V

U

i

Ii = 200 mA

= 1.0 W

P

i

Ci = 0.012 µF

= 0

L

i

TABLE 17. Temperature Sensor Connection Parameters

= 30V

U

o

Io = 19 mA

= 140 mW

P

o

Ci = 0.002 µF

= 0

L

i

TABLE 18. Temp Sensor Terminals Connection Parameters

C

= 0.066 ␮F Gas Group IIC

o

Co = 0.560 ␮F Gas Group IIB

= 1.82 ␮F Gas Group IIA

C

o

Lo = 96 mH Gas Group IIC

= 365 mH Gas Group IIB

L

o

Lo = 696 mH Gas Group IIA

= 247 ␮H/ohm Gas Group IIC

L

o/Ro

Lo/Ro = 633 ␮H/ohm Gas Group IIB

= 633 ␮H/ohm Gas Group IIA

L

o/Ro

Special Conditions for Safe Use

The 3095, when fitted with the transient terminal block (order code B), are not capable of withstanding the 500 volts insulation test required by EN50 020, Clause 6.4.12 (1994). This condition must be accounted for during installation.

N1 ATEX Type N

Certificate Number: BAS98ATEX3360X II 3 G

EEx nL IIC T5 (T EEx nL IIC T4 (T

= 55V

U

i

= –45 °C to 40 °C)

amb

= –45 °C to 70 °C)

amb

= –45 °C to 40 °C)

amb

= –45 °C to 70 °C)

amb

26

The apparatus is designed for connection to a remote temperature sensor such as a resistance temperature detection (RTD)

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Special Conditions for Safe Use

The 3095, when fitted with the transient terminal block (order code B), are not capable of withstanding the 500 volts insulation test required by EN50 021, Clause 9.1 (1995). This condition must be accounted for during installation.

E1 ATEX Flameproof

Certificate Number: KEMA02ATEX2320X II 1/2 G EEx d IIC T5 (-50°C ≤ T

T6 (-50°C ≤ T

118 0

Special Conditions for Safe Use (x):

The device contains a thin wall diaphragm. Installation, maintenance, and use shall take into account the environmental conditions to which the diaphragm will be subjected. The manufacturer’s instructions for installation and maintenance shall be followed in detail to assure safety during its expected lifetime.

ND ATEX Dust

Certificate Number: KEMA02ATEX2321 II 1 D V = 55 Vdc MAX I = 23 mA MAX IP66

118 0

amb

≤ 80°C) ≤ 65°C)

Combinations of Certifications

Stainless steel certification tag is provided when optional approval is specified. Once a device labeled with multiple approval types is installed, it should not be reinstalled using any other approval types. Permanently mark the approval label to distinguish it from unused approval types.

K5 E5 and I5 combination

K6 E6 and I6 combination

K1 I1, N1, E1, and ND combination

Electro Magnetic Compatibility (EMC) (89/336/EEC)

3095 Flow Transmitters

— EN 50081-1: 1992; EN 50082-2:1995; EN 61326-1:1997 – Industrial

Ordinary Location Certification for Factory Mutual

As standard, the transmitter has been examined and tested to determine that the design meets basic electrical, mechanical, and fire protection requirements by FM, a nationally recognized testing laboratory (NRTL) as accredited by the Federal Occupational Safety and Health Administration (OSHA).

Rosemount 3095 Fieldbus Hazardous Locations Certifications

North American Certifications

FM Approvals

E5 Explosion Proof for Class I, Division 1, Groups B, C, and D.

Dust-Ignition Proof for Class II/Class III, Division 1, Groups E, F, and G. Enclosure type NEMA 4X. Factory Sealed. Provides nonincendive RTD connections for Class I, Division 2, Groups A, B, C, and D.

I5 Intrinsically Safe for use in Class I, II and III, Division 1,

Groups A, B, C, D, E, F, and G hazardous outdoor locations. Non-incendive for Class I, Division 2, Groups A, B, C, and D. Temperature Code T4. Factory Sealed.

For input parameters and installation see control drawing 03095-1020.

IE FISCO for use in Class I, II and III, Division 1, Groups A, B,

C, D, E, F, and G hazardous outdoor locations. Temperature Code T4. Factory Sealed.

Rosemount 3095 with Fieldbus

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can be found on the Rosemount website at www.rosemount.com. A hard copy may be obtained by contacting our local sales office.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

European Pressure Equipment Directive (PED) (97/23/EC)

3095F_2/3,4/D and 3095M_2/3,4/D Flow Transmitters

— QS Certificate of Assessment - EC No. PED-H-20 Module H Conformity Assessment

All other 3095_ Transmitters/Level Controller

— Sound Engineering Practice

Transmitter Attachments: Process Flange - Manifold

— Sound Engineering Practice

Primary Elements, Flowmeter

— See appropriate Primary Element QIG

For input parameters and installation see control drawing 03095-1020.

Combinations of Certifications

Stainless steel certification tag is provided when optional approval is specified. Once a device labeled with multiple approval types is installed, it should not be reinstalled using any other approval types. Permanently mark the approval label to distinguish it from unused approval types.

K5 E5 and I5 combination

Canadian Standards Association (CSA)

IF CSA FISCO Intrinsically Safe; for FOUNDATION fieldbus

protocol only

European Certifications

IA ATEX FISCO Intrinsically Safe; for FOUNDATION fieldbus

protocol only

Australian Certifications

IG IECEx FISCO Intrinsic Safety

27

Rosemount Compact Orifice

A

B

D

1.13 (28.7)

1.00 (25.4

A

B

D

1.13 (28.7)

1.00 (25.4

Flowmeter Series

DIMENSIONAL DRAWINGS

Rosemount 3095MFC Compact Orifice Mass Flowmeter

Orifice Plate Front View Orifice Plate Side View Orifice Plate Top View

Compact Orifice Plate

(Primary Element Type code P)

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

C

(Primary Element Type code C)

Conditioning Orifice Plate

TABLE 19. Dimensional Drawings

Plate Type A B Transmitter Height C D

Type P & C 5.50 (140) Transmitter Height + A 6.25 (159) 7.75 (197) - closed

(1) Measurement is in inches (millimeters).

(1)

8.25 (210) - open

C

6.0 (152) - closed

6.25 (159) - open

28

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

ORDERING INFORMATION

Rosemount 3095MFC Compact Orifice Mass Flowmeter Ordering Information

Model Product Description

3095MFC Compact Orifice Mass Flowmeter

Code Primary Element Type

C Conditioning Orifice Plate P Orifice Plate

Code Material Type

S 316 Stainless Steel (SST)

(1)

H

Code Line Size

(2) 1

005

(2)

010

(2)

015 020 2-in. (50 mm) 030 3-in. (80 mm) 040 4-in. (100 mm)

(1)

050 060 6-in. (150 mm) 080 8-in. (200 mm)

(1)

100

(1)

120

Code Primary Element Style

N Square Edged

Code Beta Ratio

040 0.40 Beta Ratio (β)

(3)

065

Code Temperature Measurement

R Remote Thermowell and RTD

(1)

T 0 No Temperature Sensor

Code Transmitter Connection Platform

3 Direct-mount, 3-valve integral manifold, SST 7 Remote-mount, 1/4-in. NPT connections

Code Differential Pressure Range

1 0 to 25 in H2O (0 to 62.2 mbar) 2 0 to 250 in H2O (0 to 623 mbar) 3 0 to 1000 in H2O (0 to 2.5 bar)

Code Static Pressure Range

B 0 – 8 to 0 – 800 psia (0 –55.16 to 0 – 5515.8 kPa) C 0 – 8 to 0 – 800 psig (0 –55.16 to 0 – 5515.8 kPa) D 0 – 36.2 to 0 – 3626 psia (0 –250 to 0 – 25000 kPa) E 0 – 36.2 to 0 – 3626 psig (0 –250 to 0 – 25000 kPa)

Code Output Protocol

A 4–20 mA with digital signal based on HART protocol V FOUNDATION fieldbus protocol

Code Transmitter Housing Style Conduit Entry Size

1A Polyurethane-covered aluminum 1B Polyurethane-covered aluminum M20 x 1.5 (CM20) 1C Polyurethane-covered aluminum PG 13.5 1J SST 1K SST M20 x 1.5 (CM20) 1L SST PG 13.5

Hastelloy

/2-in. (15 mm) 1-in. (25 mm) 11/2-in. (40 mm)

5-in. (125 mm)

10-in (250 mm) 12-in. (300 mm)

0.65 Beta Ratio (β)

Integral RTD and Thermowell

1

/2-14 NPT

1

/2-14 NPT

Flowmeter Series

29

Rosemount Compact Orifice Flowmeter Series

Rosemount 3095MFC Compact Orifice Mass Flowmeter Ordering Information

Code Options

Performance Class

(4)

U3

PlantWeb Control Functionality

(5)

A01

Installation Accessories

G DIN Alignment Ring (PN 16) H DIN Alignment Ring (PN 40, PN 100) B JIS Alignment Ring 10K R JIS Alignment Ring 20K S JIS Alignment Ring 40K

Remote Adapters

E Flange adapters 316 SST (

High Temperature Applications

T Graphite valve packing (Tmax = 850 °F)

Flow Calibration

(6)

WC

(6)

WD

Pressure Testing

P1 Hydrostatic Testing with certificate

Special Cleaning

P2 Cleaning for special processes PA Cleaning per ASTM G93 Level D (section 11.4)

Special Inspection

QC1 Visual and dimensional inspection with certificate QC7 Inspection and performance certificate

Transmitter Calibration Certification

Q4 Calibration data certificate for transmitter

Material Traceability Certification

(7)

Q8

Code Conformance

J2 ANSI B31.1 J3 ANSI B31.3 J4 ANSI B31.8

Material Conformance

(8)(9)

J5

Country Certification

J1 Canadian Registration

Product Certifications

E1 ATEX Flameproof I1 ATEX Intrinsic Safety N1 ATEX Type n K1 ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E1, I1, N1, and ND) ND ATEX Dust E5 FM Explosion-proof, Dust Ignition-proof I5 FM Intrinsically Safe, Division 2 K5 FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, Division 2 (combination of E5 and I5) E6 CSA Explosion-proof, Dust Ignition-proof, Division 2 I6 CSA Intrinsically Safe, Division 2 K6 CSA Explosion-proof, Intrinsically Safe, Division 2 (combination of E6 and I6)

(1)

IE

(1)

IF

(1)

IA

(1)

IG I7 IECEx Intrinsic Safety E4 TIIS Flameproof ID TIIS FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only

Ultra for Flow: up to ±0.70% mass flow rate accuracy, up to 10:1 turndown, 10-year stability, limited 12-year warranty

Advanced Control Function Block Suite

1

/2-in. NPT)

Discharge coefficient verification (3 point) Discharge coefficient verification (10 point)

Material certification per ISO 10474 3.1.B and EN 10204 3.1.B

NACE MR-0175 / ISO 15156

FM FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only CSA FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only ATEX FISCO Intrinsically Safe; for FOUNDATION fieldbus protocol only IECEx FISCO Intrinsic Safety

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

30

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

Rosemount 3095MFC Compact Orifice Mass Flowmeter Ordering Information

I3 China Intrinsic Safety E3 China Flameproof

Alternative Transmitter Material of Construction

(9)

L1

Display

M5 Integral mount LCD display

Terminal Blocks

T1 Transient Protection

Manifold for Remote Mount Option

F2 3-Valve Manifold, SST F6 5-Valve Manifold, SST

Typical Model Number: 3051MFC C S 040 N 040 0 3 B A 1A

(1) Consult factory for availability.

(2) Not available for Primary Element Type code C.

(3) For 2-in. (50.8 mm) line sizes the Beta Ratio is 0.6 for Primary Element Type code C.

(4) Ultra for Flow applicable for HART protocol, DP ranges 2 and 3 with SST isolator material and silicone fill fluid options only.

(5) Function Blocks include: Arithmetic, Integrator, Analog Output, Signal Characterizer, Control Selector, and Output Selector.

(6) Not available with Primary Element Type code P.

(7) Instrument valves not included in Traceability Certification.

(8) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO 15156 for sour oil field production environments. Environmental

(9) Not available with DP range 1.

Inert Sensor Fill Fluid

limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.

31

Rosemount Compact Orifice Flowmeter Series

Rosemount 405 Compact Orifice Primary Element

SPECIFICATIONS

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Performance

Discharge Coefficient Uncertainty

TABLE 20. 405 Compact Orifice Primary Element

Discharge Coefficient

Typ e Beta

405C (Conditioning Compact)

(1)(2)

405P (Standard Compact)

(1) Line sizes 1/2 to 11/2-in. (12.7 to 38.1 mm).

(2) Discharge Coefficient Uncertainty for

(3) Line sizes 2 to 12-in. (50 mm to 300 mm)

(3)

is ±2.25%.

0.4 ±0.50%

0.65 ±1.00%

0.4 ±1.75%

0.65 ±1.75%

0.4 ±1.25%

0.65 ±1.25%

1

Uncertainty

/2-in. units with Beta = 0.65

Line Sizes

•1/2-in. (15 mm) – not available for the 405C

• 1-in. (25 mm) – not available for the 405C

1

/2-in. (40 mm) – not available for the 405C

•1

• 2-in. (50 mm)

• 3-in. (80 mm)

• 4-in. (100 mm)

• 5-in (125 mm)

• 6-in. (150 mm)

• 8-in. (200 mm)

• 10-in. (250 mm)

• 12-in (300 mm)

Sizing

Contact an Emerson Process Management sales representative assistance. A “Configuration Data Sheet” is required prior to order for application verification.

Functional

Vibration Limits

Qualified per IEC61298-3 (1998) for field with high vibration level or pipeline with high vibration level (10-60Hz 0.21mm displacement peak amplitude / 60 - 500Hz 3g).

The weight and length of the transmitter assembly shall not exceed 5.8 lbs and 7.75-in.

Assembly to a transmitter

Select option code C11 for the Rosemount 3051S transmitter (or option code S3 for the Rosemount 3051C or 3095MV transmitters) to factory assemble the Rosemount 405 to a Rosemount pressure transmitter. If the 405 and transmitter are not factory assembled, they may be shipped separately. For a consolidated shipment, inform the Emerson Process Management representative when placing the order.

Physical

Material of Construction

Body/Plate

•316 SST

• 50 micro-inch Ra surface finish

Manifold Head/Valves

•316 SST

Flange Studs and Nuts

• Customer supplied

• Available as a spare part

Transmitter Connection Studs and Nuts

• Studs– A193 Grade B8M.

• Nuts– A194 Grade 8M.

Gasket and O-rings

• Gaskets are customer supplied.

• Durlon 8500 fiber gaskets are recommended. Consult an Emerson Process Management representative for use with other gaskets.

• Available as a spare part

Service

•Liquid

•Gas

• Vapor

Operating Process Temperature Limits

Standard (direct/remote mount):

• –40 to 450 °F (–40 to 232 °C)

Extended (remote mount only with option code T):

• –148 to 850 °F (–100 to 454 °C)

Differential Pressure Limits

Maximum differential pressure (DP) up to 800 inH2O.

Maximum Working Pressure

• Pressure retention per ANSI B16.5 600# or DIN PN100

32

NOTE

Gaskets and O-rings should be replaced when the 405 is disassembled.

Transmitter Connections

Direct Mount

• Integrally mount to 3051 and 3095 transmitters, range 1, 2, and 3.

Remote Mount

• Available with connections

Orifice Type

• Square edged, Wafer style

Orifice Pressure Taps

• Corner

1

/4-in. (standard) or 1/2-in. (option code E)

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

Process Connections

Mounts between the following flange configurations:

ASME B16.5 (ANSI)

Class 150

Class 300

Class 600

DIN JIS

PN16 (option code G)

PN40 (option code H)

PN100 (option code H)

10k (option code B)

20k (option code R)

40k (option code S)

ANSI alignment ring is included as standard when ordering.

Typical Orifice Hole Sizes (For 405C)

Beta is calculated by: (β) = dC / Pipe ID, where the calculated bore is equal to 2 x typical orifice hole size (d shows the diameter of each of the four typical orifice holes.

TABLE 21. β = 0.4

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.249 (6.325)

1-in. (25 mm) Not Available 0.420 (10.668)

1

/2-in. (40 mm) Not Available 0.644 (16.358)

1 2-in. (50 mm) 0.413 (10.490) 0.827 (21.006) 3-in. (80 mm) 0.614 (15.596) 1.227 (31.166) 4-in. (100 mm) 0.805 (20.447) 1.610 (40.894) 5-in. (125 mm) 1.009 (25.629) 2.019 (51.283) 6-in. (150 mm) 1.213 (30.810) 2.426 (61.620) 8-in. (200 mm) 1.596 (40.538) 3.192 (81.077) 10-in. (250 mm) 2.004 (50.902) 4.008 (101.80) 12-in. (300 mm) 2.400 (60.960) 4.800 (121.92)

TABLE 22. β = 0.65

(1)(2)

Line Size 3051SFCC 3051SFCP

1

/2-in. (15 mm) Not Available 0.404 (10.262)

1-in. (25 mm) Not Available 0.682 (17.323)

1

/2-in. (40 mm) Not Available 1.047 (26.594)

1 2-in. (50 mm) 0.620 (15.748) 3-in. (80 mm) 0.997 (25.324) 1.994 (50.648) 4-in. (100 mm) 1.308 (33.223) 2.617 (66.472) 5-in. (125 mm) 1.640 (40.640) 3.281 (83.34) 6-in. (150 mm) 1.971 (50.063) 3.942 (100.127) 8-in. (200 mm) 2.594 (65.888) 5.188 (131.775) 10-in. (250 mm) 3.257 (82.728) 6.513 (165.43) 12-in. (300 mm) 3.900 (99.060) 7.800 (198.120)

(1) Measurement is in inches (millimeters)

(2) Tolerance = ±0.002-in.

(3) Beta (β) = 0.60-in. (15.24 mm) for 2-in. line size only.

= 2d). The table below

C

(3)

1.344 (34.138)

3051SFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 10.7 (4.58) 7.5 (3.70)

1-in. (25 mm) 11.45 (5. 19) 8.25 (4.07)

1

/2-in. (40 mm) 11.95 (5.42) 8.75 (4.32)

1 2-in. (50 mm) 12.20 (5.53) 9.00 (4.44) 3-in. (80 mm) 14.20 (6.44) 11.00 (5.43) 4-in. (100 mm) 16.70 (7.57) 13.50 (6.67) 5-in. (125 mm) 18.45 (8.37) 15.25 (7.53) 6-in. (150 mm) 20.20 (9.16) 17.00 (8.40) 8-in. (200 mm) 25.45 (11.54) 22.25 (10.99) 10-in (250 mm) 30.70 (13.92) 27.50 (13.58) 12-in (300 mm) 36.70 (16.64) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 3051S Coplanar PlantWeb housing transmitter.

(1)(2)

Remote Mount (R3)

3095MFC Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 9.50 (4.69) 6.3 (3.11)

1-in. (25 mm) 10.25 (5.06) 7.05 (3.48)

1

/2-in. (40 mm) 10.75 (5.31) 7.55 (3.73)

1 2-in. (50 mm) 11.00 (5.43) 7.80 (3.85) 3-in. (80 mm) 13.00 (6.42) 9.80 (4.84) 4-in. (100 mm) 15.50 (7.65) 12.30 (6.07) 5-in. (125 mm) 17.25 (8.52) 14.05 (6.94) 6-in. (150 mm) 19.00 (9.38) 15.80 (7.80) 8-in. (200 mm) 24.25 (11.98) 21.05 (10.40) 10-in (250 mm) 29.50 (14.57) 26.30 (12.9) 12-in (300 mm) 35.50 (17.53) 32.30 (15.95)

(1) Measurement in lb (kg).

(2) Includes 3095 MultiVariable transmitter.

(1)(2)

Remote Mount (R3)

405 Weight

Line Size Direct Mount (D3)

1

/2-in. (15 mm) 3.50 (1.73) 7.5 (3.70)

1-in. (25 mm) 4.25 (2.10) 8.25 (4.07)

1

/2-in. (40 mm) 4.75 (2.34) 8.75 (4.32)

1 2-in. (50 mm) 5.00 (2.47) 9.00 (4.44) 3-in. (80 mm) 7.00 (3.45) 11.00 (5.43) 4-in. (100 mm) 9.50 (4.69) 13.50 (6.67) 5-in. (125 mm) 11.25 (5.55) 15.25 (7.53) 6-in. (150 mm) 13.00 (6.41) 17.00 (8.40) 8-in. (200 mm) 18.25 (9.00) 22.25 (10.99) 10-in (250 mm) 23.50 (11.59) 27.50 (13.58) 12-in (300 mm) 29.50 (14.55) 33.50 (16.54)

(1) Measurement in lb (kg).

(2) Includes 405 Direct Mount option D3.

(1)(2)

Remote Mount (R3)

(1)

33

Rosemount Compact Orifice

Upstream (inlet)

side of primary

405C Conditioning

Orifice

405P Compact

Orifice

Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Installation Consideration

Straight Pipe Requirement

Use the appropriate lengths of straight pipe upstream and downstream of the 405 to minimize the effects of moderate flow disturbances in the pipe. Table 23 and Table 24 lists recommended lengths of straight pipe per ISO 5167.

TABLE 23. 405C Straight Pipe Requirements

Beta 0.40 0.65

Reducer (1 line size) 2 2 Single 90° bend or tee 2 2 Two or more 90 ° bends in the same

plane Two or more 90° bends in different

plane

side of primary

Up to 10° of swirl 2 2

Upstream (inlet)

Butterfly valve (75% to 100% open) 2 N/A

Downstream (outlet) side of primary

TABLE 24. 405P Straight Pipe Requirements

Beta 0.40 0.65

(2)(3)

Downstream (outlet) side of primary

(1) Consult an Emerson Process Management representative if

(2) Recommended lengths represented in pipe diameters per ISO

(3) Refer to ISO 5167 for recommended lengths when using flow

Reducer 5 12 Single 90° bend or tee 16 44 Two or more 90 ° bends

in the same plane Two or more 90° bends in different

plane Expander 12 28 Ball / Gate valve fully open 12 18

disturbance is not listed.

5167.

straighteners.

(1)

2 2

(1)(2)(3)

10 44

50 60

6 7

Pipe Orientation

Process

Orientation/ Flow Direction

Horizontal D/R D/R D/R Vertical Up R D/R R Vertical Down D/R NR NR

(1) D = Direct mount acceptable (recommended)

R = Remote mount acceptable NR = Not recommended

Gas Liquid Steam

(1)

Pipe Centering

Improper centering of any orifice type device can cause an error of up to ±5% in small line sizes. A centering mechanism (centering ring) independent of flange rating comes standard with the 405 Compact Orifice Series.

34

Product Data Sheet

30°

120°

30°

360°

FLOW

360°

FLOW

00813-0100-4810, Rev HA March 2008

Flowmeter Orientation

Flowmeter orientation for the Conditioning Compact Orifice and standard Compact Orifice.

Gas (Horizontal)

Liquid and Steam (Horizontal)

Rosemount Compact Orifice

Flowmeter Series

50°

80°

Gas (Vertical)

Liquid (Vertical)

35

Rosemount Compact Orifice

VALVE

EQUALIZER

1/4"-in NPT

INSTRUMENT

HIGH

VALVE

LOW

ADAPTER

PLATE

.85 (21.6)

(54.1)

2.13

1.13 (28.7)

1.00 (25.4)

Flowmeter Series

DIMENSIONAL DRAWINGS

Rosemount 405 Compact Orifice Plate

(Remote Mount Transmitter)

Adapter Plate (R3) Flange Adapter (R3 with option E)

1/2"-in NPT

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

2.13

(54.1)

Compact Orifice Plate

(Primary Element Type code P)

1/4"-in NPT

HIGH

INSTRUMENT

VALVE

ADAPTER

PLATE

EQUALIZER

VALVE

2.13

(54.1)

.85 (21.6)

LOW INSTRUMENT VALVE

HIGH

INSTRUMENT

VALVE

ADAPTER

PLATE

EQUALIZER

VALVE

HIGH

INSTRUMENT

VALVE

ADAPTER

PLATE

EQUALIZER

1/2"-in NPT

VALVE

2.13

(54.1)

FLANGE ADAPTER

.85 (21.6)

1.13 (28.7)

1.00 (25.4)

LOW INSTRUMENT VALVE

FLANGE ADAPTER

LOW INSTRUMENT VALVE

.85 (21.6)

Conditioning Orifice Plate

36

(Primary Element Type code C)

1.13 (28.7)

1.00 (25.4)

1.13 (28.7)

1.00 (25.4)

Product Data Sheet

HIGH

EQUALIZER

VALVE

INSTRUMENT

LOW INSTRUMENT VALVE

1.30

1.13 (28.7)

1.00 (25.4)

(33)

2.13

(54.1)

1.13 (28.7)

1.00 (25.4)

00813-0100-4810, Rev HA March 2008

Front View (transmitter connection A3) Front View (transmitter connection D3)

HIGH

INSTRUMENT

VALVE

ADAPTER

PLATE

EQUALIZER

VALVE

Rosemount Compact Orifice

Flowmeter Series

Rosemount 405 Compact Orifice Plate

(Direct Mount)

2.13

(54.1)

LOW INSTRUMENT VALVE

.70 (18)

Compact Orifice Plate

(Primary Element Type code P)

(Primary Element Type code C)

Conditioning Orifice Plate

1.13 (28.7)

1.00 (25.4)

HIGH

INSTRUMENT

VALVE

EQUALIZER

VALVE

1.30 (33)

2.13

(54.1)

LOW INSTRUMENT VALVE

1.13 (28.7)

1.00 (25.4)

NOTE

Transmitter connection code A3 is to be used with a traditional style transmitter (such as a Rosemount 1151). This is a stainless steel adapter plate for allowing the direct mount of traditional style transmitters.

37

Rosemount Compact Orifice Flowmeter Series

ORDERING INFORMATION

Rosemount 405 Compact Orifice Primary Element Ordering Information

Model Product Description

405 Compact Primary Element

Code Primary Element Type

C Conditioning Orifice Plate P Orifice Plate

Code Material Type

S 316 Stainless Steel (SST)

(1)

H

Code Line Size

(2) 1

005

(2)

010

(2)

015 020 2-in. (50 mm) 030 3-in. (80 mm) 040 4-in. (100 mm)

(1)

050 060 6-in. (150 mm) 080 8-in. (200 mm)

(1)

100

(1)

120

Code Temperature Measurement

R Remote Thermowell and RTD

(1)

T 0 No Temperature Sensor

Code Beta Ratio

040 0.40 Beta Ratio (β)

(3)

065

Code Transmitter Connection

D3 Coplanar, Direct mount, 3-valve integral manifold, SST R3 Remote-mount, 1/4-in. NPT connections A3 Traditional, Direct mount, 3-valve integral manifold with adapter plate, SST

Code Options

Installation Accessories

G DIN Alignment Ring (PN 16) H DIN Alignment Ring (PN 40, PN 100) B JIS Alignment Ring 10K R JIS Alignment Ring 20K S JIS Alignment Ring 40K

Adapters

E Flange adapters 316 SST (

High Temperature Applications

T Graphite valve packing (Tmax = 850 °F)

Flow Calibration

(4)

WC

(4)

WD

Pressure Testing

P1 Hydrostatic testing with certificate

Special Cleaning

P2 Cleaning for special processes PA Cleaning per ASTM G93 Level D (section 11.4)

Continued on Next Page

Hastelloy

/2-in. (15 mm) 1-in. (25 mm) 11/2-in. (40 mm)

5-in. (125 mm)

10-in. (250 mm) 12-in. (300 mm)

Integral RTD and Thermowell

0.65 Beta Ratio (β)

1

/2-in. NPT)

Discharge coefficient verification (3 point) Discharge coefficient verification (10 point)

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

38

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

Rosemount 405 Compact Orifice Primary Element Ordering Information

Special Inspection

QC1 Visual and Dimensional Inspection with certification QC7 Inspection and performance certification

Material Traceability Certification

(5)

Q8

Code Conformance

J2 ANSI B31.1 J3 ANSI B31.3 J4 ANSI B31.8

Material Conformance

(6)

J5

Country Certification

J1 Canadian Registration

Typical Model Number: 405 C S 040 N 040 D3

(1) Consult factory for availability.

(2) Not available for Primary Element Type code C.

(3) For 2-in. (50.8 mm) line sizes the Beta Ratio is 0.6 for Primary Element Type code C.

(4) Not available with Primary Element Type code P.

(5) Instrument valves not included in Traceability Certification.

(6) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits

Material certification per ISO 10474 3.1.B and EN 10204 3.1.B

NACE MR-0175 / 15156

apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.

39

Rosemount Compact Orifice

Product Data Sheet

00813-0100-4810, Rev HA

Flowmeter Series

March 2008

HART Configuration Data Sheet (CDS)

DP FLOW CDS

Complete this form to define a custom flow configuration for DP Flowmeters. Unless specified, the flowmeter will be shipped with the default values identified by the H symbol.

For technical assistance in filling out this CDS, call a Rosemount representative.

NOTE

Any missing information will be processed with the indicated default values.

* = Required Item ★ = Default

Customer Information

Customer: Contact Name:

Customer Phone: Customer Fax:

Customer Approval Sign-Off: Customer PO:

Calculation Approval

❑ Check this box if a calculation for approval prior to manufacturing is required

Application and Configuration Data Sheet (Required with Order)

Ta g:

Model No

* Select fluid type ❑ Liquid ❑ Gas ❑ Steam

* Fluid name

Flowmeter Information (optional)

* Failure Mode Alarm Direction (select one)

Software Tag: ___ ___ ___ ___ ___ ___ ___ ___ (8 characters)

Descriptor: ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ (16 characters)

Message: ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

Date: Day __ __ (numeric) Month __ __ (numeric) Year __ __ (numeric)

(1) A complete model number is required before Rosemount Inc. can process the order.

(2) If the Fluid is not located in Table 25 on page 42, the “Ordering Information” on page 38 must be completed.

(1)

(2)

❑ Alarm High★❑ Alarm Low

___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ (32 characters)

For Rosemount Use Only

S.O.: LI

CHAMP: DATE:

ADMIN:

40

Product Data Sheet

00813-0100-4810, Rev HA March 2008

* = Required Item ★ = Default

Primary Element Information

* Select Differential Producer (Select One)

Annubar

❑ 485 Annubar/ 3095MFA Mass ProBar, 3051SFA ProBar ❑ 285 Annubar ❑ Annubar Diamond II + / Mass Probar ❑ Long Radius Wall Taps, ASME ❑ Long Radius Wall Taps, ISO ❑ ISA 1932, ISO

Venturi

❑ Nozzle, ISO ❑ Rough Cast/Fabricated Inlet, ASME ❑ Round Cast Inlet, ISO ❑ Machined Inlet, ASME ❑ Machined Inlet, ISO ❑ Welded Inlet, ISO

Other (All options require a discharge coefficient value)

❑ Calibrated Orifice: Flange, Corner, or D & D/2 Taps.

Discharge coefficient: __________________

❑ Calibrated Orifice: 2

Discharge coefficient: __________________

1

/2 D & 8D Taps

❑ Calibrating Nozzle

Discharge coefficient: __________________

❑ Calibrating Venturi

Discharge coefficient: __________________

❑ Area Averaging Meter

Discharge coefficient: __________________

❑ V-Cone

Discharge coefficient: __________________

Special Annubar dimension (required if customer supplies mounting hardware).

®

Diameter (d) ________________

Orifice

❑ 3051SFP, 3095MFP, 1195 ❑ 405C, 405P, 3051SFC, 3095MFC ❑ 1595 Conditioning Orifice ❑ 2 ❑ Corner Taps, ASME ❑ Corner Taps, ISO ❑ D & D/2 Taps, ASME ❑ D & D/2 Taps, ISO ❑ D & D/2 Taps, ISO 99 Amendment 1 ❑ Flange Taps, AGA ❑ Flange Taps, ASME ❑ Flange Taps, ISO ❑ Flange Taps, ISO 99 Amendment 1 ❑ Small Bore, Flange Taps, ASME

❑ inch★ ❑ millimeters

Rosemount Compact Orifice

Flowmeter Series

1

/2D & 8D Taps, ASME

at __________

❑ ODF _____ ❑ ODT _____

❑ °F ❑ 68 °F★

❑ °C

Pipe Information

* Orientation / Flow Direction:

* Line Size / Schedule: ___________________________________ Body I.D. (D): ___________________________________

Materials of Construction

* Pipe Material

* Primary Element Material

Operating Conditions

4 mA value Minimum Normal Maximum Full Scale:20 mA flow rate

Flow Rate 0 *

Pressure (P) — *

Temperature (T) — *

RTD Mode

❑ Vertical Up ❑ Vertical Down ❑ Horizontal

❑ Carbon Steel ❑ 304 SST ❑ 316 SST ❑ Hastelloy ❑ Other ________________

❑ 316 SST ❑ Hastelloy ❑ Other ___________________ (Please verify material availability)

(1)

**

* *

(1)

(design to P and T)

(2)

*

Design

❑ Normal Mode ★ (Requires a RTD to be connected. If the RTD is disconnected or fails, the 3095MV output goes to alarm value)

❑ Fixed Temperature Mode: Specify the fixed temperature value _____________________ ❑ °F ❑ °C

❑ Backup Mode (Uses the connected RTD for temperature measurement. If the RTD is disconnected or fails, the transmitter uses a fixed

temperature value as a backup. This will not cause the mA output to go to alarm value and can potentially cause inaccurate flow measurement.) Fixed temperature value to be used as backup_________________

❑ °F ❑ °C

41

Rosemount Compact Orifice

Product Data Sheet

00813-0100-4810, Rev HA

Flowmeter Series

March 2008

* = Required Item ★ = Default

Base Conditions

❑ Standard Base (P=14.696 psia / 101.325 kPa abs, T= 60 °F (15.56 °C))

❑ Normal Base (P=14.696 psia / 101.325 kPa abs, T= 32 °F (0 °C))

❑ Standard Base for Natural Gas (AGA) (P=14.73 psia, T= 60°F (15.56 °C))

❑ User Defined: P= ________ Units: ________ T= ________ Units = ________

Compressibility at Base: ________________________ OR Density at Base: ________________________

(1) Operating ranges for pressure and temperature are needed for transmitter configuration.

(2) Required to verify that the product selection meets design criteria.

TABLE 25. Rosemount Fluids Database

Acetic Acid Acetone Acetonitrile Acetylene Acrylonitrile Air Allyl Alcohol Ammonia Argon Benzene Benzaldehyde Benzyl Alcohol Biphenyl Carbon Dioxide Carbon Monoxide Carbon Tetrachloride Chlorine Chlorotrifluoroethylene Chloroprene Cycloheptane Cyclohexane Cyclopentane Cyclopentene Cyclopropane

(1) This list is subject to change without notice. Steam per ASME Steam tables. All other fluids per AlChE.

Divinyl Ether Ethane Ethanol Ethylamine Ethylbenzene Ethylene Ethylene Glycol Ethylene Oxide Fluorene Furan Helium-4 Hydrazine Hydrogen Hydrogen Chloride Hydrogen Cyanide Hydrogen Peroxide Hydrogen Sulfide Isobutane Isobutene Isobutyl benzene Isopentane Isoprene Isopropanol

(1)

Methane Methanol Methyl Acrylate Methyl Ethyl Ketone Methyl Vinyl Ether m-Chloronitrobenzene Neon Neopentane Nitric Acid Nitric Oxide Nitrobenzene m-Dichlorobenzene Nitroethane Nitrogen Nitromethane Nitrous Oxide n-Butane n-Butanol n-Butyraldehyde n-Butyronitrile n-Decane n-Dodecane n-Heptadecane n-Heptane

n-Hexane n-Octane n-Pentane Oxygen Pentafluorothane Phenol Propadiene Pyrene Propylene Styrene Sulfer Dioxide Propane Toluene Trichloroethylene Vinyl Acetate Vinyl Chloride Vinyl Cyclohexane Water 1-Butene 1-Decene 1-Decanal 1-Decanol 1-Dodecene 1-Dodecanol

1-Heptanol 1-Heptene 1-Hexene 1-Hexadecanol 1-0ctanol 1-Octene 1-Nonanol 1-Pentadecanol 1-Pentanol 1-Pentene 1-Undecanol 1-Nonanal 1,2,4- Trichlorobenzene 1,1,2- Trichloroethane 1,1,2,2- Tetrafluoroethane 1,2-Butadiene 1,3-Butadiene 1,3,5- Trichlorobenzene 1,4-Dioxane 1,4-Hexadiene 2-Methyl-1-Pentene 2,2-Dimethylbutane

Drawing/Notes

42

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

FOUNDATION fieldbus™ Configuration Data Sheet (CDS)

DP FLOW CDS

Complete this form to define a custom flow configuration for DP Flowmeters. Unless specified, the flowmeter will be shipped with the default values identified by the H symbol.

For technical assistance in filling out this CDS, call a Rosemount representative.

NOTE

Any missing information will be processed with the indicated default values.

* = Required Item ★ = Default

Customer Information

Customer: Contact Name:

Customer Phone: Customer Fax:

Customer Approval Sign-Off: Customer PO:

Calculation Approval

❑ Check this box if a calculation for approval prior to manufacturing is required

Application and Configuration Data Sheet (Required with Order)

Ta g:

Model No

* Select fluid type ❑ Liquid ❑ Gas ❑ Steam

* Fluid name

Flowmeter Information (optional)

* Failure Mode Alarm Direction (select one)

Software Tag: ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ (16 characters)

Descriptor: ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

Message: ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___

Date: Day __ __ (numeric) Month __ __ (numeric) Year __ __ (numeric)

(1) A complete model number is required before Rosemount Inc. can process the order.

(2) If the Fluid is not located in Table 26 on page 45, the “Ordering Information” on page 38 must be completed.

(1)

(2)

❑ Alarm High★❑ Alarm Low

___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ ___ (32 characters)

For Rosemount Use Only

S.O.: LI

CHAMP: DATE:

ADMIN:

43

Rosemount Compact Orifice Flowmeter Series

* = Required Item ★ = Default

Primary Element Information

* Select Differential Producer (Select One)

Annubar

❑ 485 Annubar/ 3095MFA Mass ProBar, 3051SFA ProBar ❑ 285 Annubar ❑ Annubar Diamond II + / Mass Probar ❑ Long Radius Wall Taps, ASME ❑ Long Radius Wall Taps, ISO ❑ ISA 1932, ISO

Venturi

❑ Nozzle, ISO ❑ Rough Cast/Fabricated Inlet, ASME ❑ Round Cast Inlet, ISO ❑ Machined Inlet, ASME ❑ Machined Inlet, ISO ❑ Welded Inlet, ISO

Other (All options require a discharge coefficient value)

❑ Calibrated Orifice: Flange, Corner, or D & D/2 Taps.

Discharge coefficient: __________________

❑ Calibrated Orifice: 2

Discharge coefficient: __________________

1

/2 D & 8D Taps

❑ Calibrating Nozzle

Discharge coefficient: __________________

❑ Calibrating Venturi

Discharge coefficient: __________________

❑ Area Averaging Meter

Discharge coefficient: __________________

❑ V-Cone

Discharge coefficient: __________________

Special Annubar dimension (required if customer supplies mounting hardware).

®

Diameter (d) ________________

Orifice

❑ 3051SFP, 3095MFP, 1195 ❑ 405C, 405P, 3051SFC, 3095MFC ❑ 1595 Conditioning Orifice ❑ 2 ❑ Corner Taps, ASME ❑ Corner Taps, ISO ❑ D & D/2 Taps, ASME ❑ D & D/2 Taps, ISO ❑ D & D/2 Taps, ISO 99 Amendment 1 ❑ Flange Taps, AGA ❑ Flange Taps, ASME ❑ Flange Taps, ISO ❑ Flange Taps, ISO 99 Amendment 1 ❑ Small Bore, Flange Taps, ASME

❑ inch★ ❑ millimeters

1

/2D & 8D Taps, ASME

at __________

❑ ODF _____ ❑ ODT _____

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

❑ °F ❑ 68 °F★

❑ °C

Pipe Information

* Orientation / Flow Direction:

* Line Size / Schedule: ___________________________________ Body I.D. (D): ___________________________________

Materials of Construction

* Pipe Material

* Primary Element Material

Operating Conditions

4 mA value Minimum Normal Maximum Full Scale:20 mA flow rate

Flow Rate 0 *

Pressure (P) — *

Temperature (T) — *

RTD Mode

❑ Vertical Up ❑ Vertical Down ❑ Horizontal

❑ Carbon Steel ❑ 304 SST ❑ 316 SST ❑ Hastelloy ❑ Other ________________

❑ 316 SST ❑ Hastelloy ❑ Other ___________________ (Please verify material availability)

(1)

**

* *

(1)

(design to P and T)

(2)

*

Design

❑ Normal Mode ★ (Requires a RTD to be connected. If the RTD is disconnected or fails, the 3095MV output goes to alarm value)

❑ Fixed Temperature Mode: Specify the fixed temperature value _____________________ ❑ °F ❑ °C

❑ Backup Mode (Uses the connected RTD for temperature measurement. If the RTD is disconnected or fails, the transmitter uses a fixed

temperature value as a backup. This will not cause the mA output to go to alarm value and can potentially cause inaccurate flow measurement.) Fixed temperature value to be used as backup_________________

❑ °F ❑ °C

44

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

* = Required Item ★ = Default

Base Conditions

❑ Standard Base (P=14.696 psia / 101.325 kPa abs, T= 60 °F (15.56 °C))

❑ Normal Base (P=14.696 psia / 101.325 kPa abs, T= 32 °F (0 °C))

❑ Standard Base for Natural Gas (AGA) (P=14.73 psia, T= 60°F (15.56 °C))

❑ User Defined: P= ________ Units: ________ T= ________ Units = ________

Compressibility at Base: ________________________ OR Density at Base: ________________________

(1) Operating ranges for pressure and temperature are needed for transmitter configuration.

(2) Required to verify that the product selection meets design criteria.

TABLE 26. Rosemount Fluids Database

Acetic Acid Acetone Acetonitrile Acetylene Acrylonitrile Air Allyl Alcohol Ammonia Argon Benzene Benzaldehyde Benzyl Alcohol Biphenyl Carbon Dioxide Carbon Monoxide Carbon Tetrachloride Chlorine Chlorotrifluoroethylene Chloroprene Cycloheptane Cyclohexane Cyclopentane Cyclopentene Cyclopropane

(1) This list is subject to change without notice. Steam per ASME Steam tables. All other fluids per AlChE.

Divinyl Ether Ethane Ethanol Ethylamine Ethylbenzene Ethylene Ethylene Glycol Ethylene Oxide Fluorene Furan Helium-4 Hydrazine Hydrogen Hydrogen Chloride Hydrogen Cyanide Hydrogen Peroxide Hydrogen Sulfide Isobutane Isobutene Isobutyl benzene Isopentane Isoprene Isopropanol

(1)

Methane Methanol Methyl Acrylate Methyl Ethyl Ketone Methyl Vinyl Ether m-Chloronitrobenzene Neon Neopentane Nitric Acid Nitric Oxide Nitrobenzene m-Dichlorobenzene Nitroethane Nitrogen Nitromethane Nitrous Oxide n-Butane n-Butanol n-Butyraldehyde n-Butyronitrile n-Decane n-Dodecane n-Heptadecane n-Heptane

n-Hexane n-Octane n-Pentane Oxygen Pentafluorothane Phenol Propadiene Pyrene Propylene Styrene Sulfer Dioxide Propane Toluene Trichloroethylene Vinyl Acetate Vinyl Chloride Vinyl Cyclohexane Water 1-Butene 1-Decene 1-Decanal 1-Decanol 1-Dodecene 1-Dodecanol

1-Heptanol 1-Heptene 1-Hexene 1-Hexadecanol 1-0ctanol 1-Octene 1-Nonanol 1-Pentadecanol 1-Pentanol 1-Pentene 1-Undecanol 1-Nonanal 1,2,4- Trichlorobenzene 1,1,2- Trichloroethane 1,1,2,2- Tetrafluoroethane 1,2-Butadiene 1,3-Butadiene 1,3,5- Trichlorobenzene 1,4-Dioxane 1,4-Hexadiene 2-Methyl-1-Pentene 2,2-Dimethylbutane

Block Tag Names

AI Block Name (Flow): ____________________________ (AI 1400 ★) AI Block Name (DP): ____________________________ (AI 1500 ★) AI Block Name (SP): ____________________________ (AI 1600 ★) AI Block Name (PT): ____________________________ (AI 1700 ★) INTEG Block Name (Flow Total): ____________________________ (INTEG 2100 ★)

Drawing/Notes

45

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Fluid Data Sheet (FDS)

For custom fluid not in the Rosemount Fluid Database

For technical assistance in filling out this CDS, call an Emerson Process Management representative. Complete this form to define a custom fluid. The H symbol identifies the default value.

NOTE

This form is not required if using the Rosemount Fluid Database.

* = Required Item ★ = Default

Customer Information

Customer: Contact Name:

Customer Phone: Customer Fax:

Customer PO:

Fluid Properties

❑ Custom Liquid– Complete Table ❑ Liquid

❑ Custom Gas– Complete Table ❑ Gas

❑ Custom Natural Gas– Complete Table ❑ Natural Gas

For Rosemount Use Only

S.O.: LI

CHAMP: DATE:

ADMIN:

46

Product Data Sheet

Rosemount Compact Orifice

00813-0100-4810, Rev HA March 2008

Flowmeter Series

TABLE 27. Custom Liquid Worksheet

* = Required Item ★ = Default

Mass Liquid Density and Viscosity Information

1. Fill in the following operating temperatures

a) _________________________ min

1

b) _________________________ [

c) _________________________ [

d) _________________________ max

2. Transfer the values from the above section to the numbered lines below.

3. Check one Density box, then enter the values for each temperature and the standard density.

4. Check one Viscosity box, then enter values for each temperature. (At least one viscosity value is required). Density

❑ Density in lbs/CuFt ❑ Density in kg/CuM

/3 (max - min))] + min

2

/3 (max - min))] + min

Viscosity

❑ Viscosity in centipoise ❑ Viscosity in lbs/ft sec ❑ Viscosity in pascal sec

Temperature Temperature a) _____________ min a) _____________ min.

1

b) _____________ [

c) _____________ [

/3 (max - min))] + min b) _____________ [1/3 (max - min))] + min

2

/3 (max - min))] + min c) _____________ [2/3 (max - min))] + min

d) _____________ max d) _____________ max

Base density: __________________________________________________________ (at base reference conditions specified)

Volumetric Liquid Density and Viscosity Information

* Density at Flow: _________________________________________________ Units: ❑ lb/ft3❑ Kg/m3❑ Other:

OR

Specific Gravity at Flow: ____________________________________________

* Viscosity at Flow: ________________________________________________ Units: ❑ Centipoise ❑ Other:

47

Rosemount Compact Orifice Flowmeter Series

TABLE 28. Custom Gas Worksheet

* = Required Item ★ = Default

Mass Gas Compressibility and Viscosity Information

1. Fill in the following operating pressures and operating temperatures

Operating Pressures Operating Temperatures

1) _____________ min 5) _____________ min

1

2) _____________ [

3) _____________ [

4) _____________ max 8) _____________ [

2. Transfer the values from the above section to the numbered lines below

3. Check one Density/Compressibility box, then enter the 12 values for each pressure/temperature range.

4. Check one Viscosity box, then enter values for each temperature. (At least one viscosity value is required).

5. Enter values for molecular weight, isentropic exponent, and standard density (or standard compressibility). Density

❑ Density in lbs/CuFt ❑ Density in kg/CuM ❑ Compressibility

Pressure Temperature Temperature

/3 (max - min))] + min 6) _____________ [1/2 (max - min))] + min

2

/3 (max - min))] + min 7) _____________ max

1

/3 (max - min))] + min

2

9) _____________ [

Viscosity

/3 (max - min))] + min

❑ Viscosity in centipoise ❑ Viscosity in lbs/ft sec ❑ Viscosity in pascal sec

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

1) ____________ 5) _____________________________ 5) ________________________________________

2) ____________ 5) _____________________________ 8) ________________________________________

3) ____________ 5) _____________________________ 9) ________________________________________

4) ____________ 5) _____________________________ 7) ________________________________________

1) ____________ 6) _____________________________

2) ____________ 6) _____________________________ Molecular Weight: _________________________

3) ____________ 6) _____________________________ Isentropic Exponent: _______________________ 1.4

4) ____________ 6) _____________________________

1) ____________ 7) _____________________________

2) ____________ 7) _____________________________

3) ____________ 7) _____________________________

4) ____________ 7) _____________________________

Standard density/compressibility: __________________________________________________________

Volumetric Gas Compressibility and Viscosity Information

* Density at Flow: ______________________________ Units: ❑ lb/ft3❑ Kg/m3❑ Other:

OR

M.W. / Specific Gravity at Flow: _________________________________________________

★

Compressibility at Flow: _____________________________________________________

Compressibility at Base: ____________________________________________________

* Viscosity at Flow: _____________________________ Units: ❑ Centipoise ❑ Other: Isentropic Exponent (K):______ 1.4 ★

48

Product Data Sheet

00813-0100-4810, Rev HA March 2008

Rosemount Compact Orifice

Flowmeter Series

49

Rosemount Compact Orifice Flowmeter Series

Product Data Sheet

00813-0100-4810, Rev HA

March 2008

Standard Terms and Conditions of Sale can be found at www.rosemount.com\terms_of_sale The Emerson logo is a trade mark and service mark of Emerson Electric Co. Rosemount, the Rosemount logotype, ProPlate, Mass ProPlate, and Annubar are registered trademarks of Rosemount Inc. All other marks are the property of their respective owners.

Emerson Process Management Rosemount Inc.

8200 Market Boulevard Chanhassen, MN USA 55317 T (US) (800) 999-9307 T (Intnl) (952) 906-8888 F (952) 949-7001

www.rosemount.com

Emerson Process Management

Heath Place Bognor Regis West Sussex PO22 9SH England T 44 (0) 1243 863121 F 44 (0) 1243 867554

Emerson Process Management Asia Pacific Private Limited

1 Pandan Crescent Singapore 128461 T (65) 6777 8211 F (65) 6777 0947 Enquiries@AP.EmersonProcess.com

¢00813-0100-4810;¤

Rosemount 3095MFC Data sheet

Specifications and Main Features

Frequently Asked Questions

User Manual