Page 1
QuickGrip™
Parts
Instruction Sheet
QuickGrip
12-0500
Instructions for Hanging
Step 1
For use with poster paper or thinner substrates.
Score and fold or staple poster edge and slide
into the QuickGrip Holder. When using staples,
place staples 1/4” from top and bottom edges of
poster. Fig. 1
or
For use with thicker graphics up to 2mm.
Starting at one corner push the QuickGrip
Holder onto the graphic. Work your way down
the holder tapping it firmly down to seat the
graphic fully. Fig. 2
Step 2
Place cable into inner channel of CableClip.
The cable should snap into place. Fig. 3
Cable Clips
06-5050
End Caps
Figure 1
06-5525
Cable and
Saucer
16-0018SS
Figure 2
Step 3
Align one end of the CableClip with the top
channel of the plastic holder. Then insert one
round end, press down on the other round end
and slide CableClip into rail. Fig. 4 Repeat step
3 for second CableClip.
Step 4
Push end caps into place. Fig. 5
Suspend poster. Fig. 6
Important note:
Please save and reuse the QuickGrip
Holder, End Caps and CableClips
for future projects.
The QuickGrip is a registered trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products. Part #02INSQuickGCCSaucer
Incept-11.13.02
Figure 3 Figure 4
Figure 6Figure 5
35 Congress Street, Salem, MA 01970
Tel# 1- 800-631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Page 2
QuickGrip™
Instruction Sheet
Parts
QuickGrip
12-0500
Instructions for Hanging
Step 1
For use with poster paper or thinner
substrates. Score and fold or staple poster
edge and slide into the QuickGrip Holder.
When using staples, place staples 1/4” from
top and bottom edges of poster. Fig. 1
or
For use with thicker graphics up to 2mm.
Starting at one corner push the QuickGrip
Holder onto the graphic. Work your way
down the holder tapping it firmly down to
seat the graphic fully. Fig. 2
Cable Clip
06-5050
End Caps
Figure 1
06-5525
Cable and
Saucer
16-0018SS
Figure 2
Step 2
Place cable into inner channel of CableClip.
The cable should snap into place. Fig. 3
Step 3
Align one end of the CableClip with the
top channel of the plastic holder. Then
insert one round end, press down on
the other round end and slide CableClip
into rail. Fig. 4
Step 4
Push end caps into place. Fig. 5
Suspend poster. Fig. 6
Important note:
Please save and reuse the QuickGrip
Holder, End Caps and CableClips
for future projects.
The QuickGrip is a registered trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products. Part #02INSQuickGCCSaucer
Incept-11.13.02
Figure 3 Figure 4
Figure 6Figure 5
35 Congress Street, Salem, MA 01970
Tel# 1- 800-631-9707 Fax# 1-800-560-2890
e-mail:signware@rosedisplays.com
Page 3
QuickGrip™
Instruction Sheet
Parts
QuickGrip
12-0500
Instructions for Hanging
Step 1
For use with poster paper or thinner substrates.
Score and fold or staple poster edge and slide
into the QuickGrip Holder. When using staples,
place staples 1/4” from top and bottom edges of
poster. Fig. 1
or
For use with thicker graphics up to 2mm.
Starting at one corner push the QuickGrip
Holder onto the graphic. Work your way
down the holder tapping it firmly down
to seat the graphic fully. Fig. 2
Cable Clips
06-5050
End Caps
Figure 1
06-5525
Cable and
Saucer
16-0018SS
Figure 2
Step 2
Place cable into inner channel of CableClip.
The cable should snap into place. Fig. 3
Step 3
Align one end of the CableClip with the top
channel of the plastic holder. Then insert one
round end, press down on the other round end
and slide CableClip into rail. Fig. 4 Repeat steps
3 for second CableClip.
Step 4
Push end caps into place. Fig. 5
Suspend poster. Fig. 6
Important note:
Please save and reuse the QuickGrip
Holder, End Caps and CableClips
for future projects.
The QuickGrip is a registered trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products. Part #02INSQuickGCCSaucer
Figure 3 Figure 4
Figure 6Figure 5
Incept-11.13.02
Page 4
QuickGrip™
Instruction Sheet
Parts
QuickGrip
12-0500
Instructions for Hanging
Step 1
For use with poster paper or thinner
substrates. Score and fold or staple poster
edge and slide into the QuickGrip Holder.
When using staples, place staples 1/4” from
top and bottom edges of poster. Fig. 1
or
For use with thicker graphics up to 2mm.
Starting at one corner push the QuickGrip
Holder onto the graphic. Work your way
down the holder tapping it firmly down to
seat the graphic fully. Fig. 2
Cable Clip
06-5050
End Caps
06-5525
Figure 1
Cable and
Saucer
16-0018SS
Figure 2
Step 2
Place cable into inner channel of CableClip.
The cable should snap into place. Fig. 3
Step 3
Align one end of the CableClip with the
top channel of the plastic holder. Then
insert one round end, press down on
the other round end and slide CableClip
into rail. Fig. 4
Step 4
Push end caps into place. Fig. 5
Suspend poster. Fig. 6
Important note:
Please save and reuse the QuickGrip
Holder, End Caps and CableClips
for future projects.
The QuickGrip is a registered trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products. Part #02INSQuickGCCSaucer
Figure 3 Figure 4
Figure 6Figure 5
Incept-11.13.02
Loading...