RONDA 5040B User Manual

Reset:

The 3 chronograph hands are returned to their zero position

Display interval:

e.g. 10 minutes 10 seconds (timing continues in the background)

Start: (start timing)

		2 1
Cal. 5040.B		30			60
	20	10		45	15
					30
		9	10	1
		8		2
		7		3
		6	5	4

English

User’s Manual

Description of the display and control buttons

Display elements						Control buttons
Date
Second hand		2 1				Push button A
Minute hand	30				60
				45	15
20	10					Crown
Hour hand			10		30
	8	9		1
Centre stop-second				2		Push button B
	7	6		3
			5	4

Minute counter

1⁄10 second counter

(houer counter after 30 minutes)

Minute counter			Push-button A
2
30
20			30
9	10	1
8		2
7		3
6	5	4
1⁄10 second counter
2
30
20			15
			30
9	10	1
8		2
7		3
6	5	4

Push-button B

Chronograph:

Accumulated timing

Example:

Start: (start timing)
Stop: (e.g. 15 min	5 sec following )
Restart: (timing is resumed)
*Stop: (e.g. 13 min	5 sec following )

= 28 min 10 sec

(The accumulated measured time is shown)

Reset:

The three chronograph hands are returned to their zero positions.

Please note:

*Following , the accumulation of the timing can be continued by pressing pushbutton A

(Restart / Stop, Restart / Stop, …)

Minute counter			Center stop-
2			second
30
20			15
			30
9	10	1	I	II III
8		2
7		3
6	5	4
1⁄10 second counter
			Push-button A
30
20			15
9	10	1		III
8		2
7		3
6	5	4

Push-button B

Adjusting the chronograph hands to zero position

Example:

One or several chronograph hands are not in their correct zero positions and have to be adjusted (e.g. following a battery change).

Pull out the crown to position III (all 3 chronograph hands are in their correct or incorrect zero position).

Keep push-buttons A and B depressed simultaneously for at least 2 seconds

(the centre stop-second rotates by 360° corrective mode is activated).

Second hand

1

30			60
20		45	15
			30
9	10	1	I	II	III
8		2
7		3
6	5	4

	2 1
	30			60
20	10		45	15
				30
	9	10	1	I	II	III
	8		2
	7		3
	6	5	4

Setting the time

*Pull out the crown to position III (the watch stops).

Turn the crown until you reach the correct time 8:45.

*Push the crown back into position I.

Please note:

* In order to set the time to the exact second,must be pulled out when the second hand is in position «60».

Once the hour and minute hands have been set, must be pushed back into position I at the exact second.

RONDA AG
CH-4415 Lausen/Switzerland
www.ronda-startech.com	11/2006

Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW)

Accuracy: +20 / -10 seconds per month

In case your watch needs to be repaired or to raise claims under a guarantee, please contact the point of sales

Minute counter Push-button A

	2 1
30
		15
	6	5

1⁄10 second counter

	2 1
	30
20	10	15
	9
	8
	7
	6

Push-button B

Chronograph: Basic function

(Start / Stop / Reset)

Example:

Start: Press push-button A.

Stop: to stop the timing, press pushbutton A once more and read the three chronograph hands: 4min/38sec /7⁄10 sec

Zero positioning:

Press push-button B.

(The three chronograph hands will be reset to their zero positions).

Minute counter

Push-button A

Chronograph:

2
30
20			30
9	10	1
8		2
7 6	5	4 3

1⁄10 second counter Push-button B

2
30
20			15
			30
9	10	1
8			2
7		4	3
6	5

Push-button B

Intermediate or interval timing

Example:

* Making up the measured time:

(the 3 chronograph hands are quickly advanced to the ongoing measured time).

Stop: (Final time is displayed)

Please note:

*Following , further intervals or intermediates can be displayed by pressing push-button B (display interval / make up measured time, ...)

A

B

A

B

A

I

II

III

Adjusting the centre stop second

Single step	A		1 x short
Continuous	A		long

Adjusting the next hand B

Adjusting the 1⁄10 second counter hand (position 6h)

Single step	A		1 x short
Continuous	A		long

Adjusting the next hand B

Adjusting the minute counter hand (position 9h)

Single step	A		1 x short
Continuous	A		long

Returning the crown to position I

Termination of the chronograph hands adjustment (can be carried out at any time).

31

20			30
9	10	1	I	II
8			2
7		4	3
6	5

0 1
20			30
9	10	1	I II
8			2
7		4	3
6	5

Setting the date (quick mode)

Pull out the crown to position II (the watch continues to run).

Turn the crown until the correct date 01 appears.

Push the crown back into position I.

Please note:

During the date changing phase between

9 PM and 12 PM; the date must be set to the date of the following day.

An extreme acceleration in setting the date with quick mode can induce a false date indication. The synchronization is re-established by setting the date from 01 till 31 (crown in position II).

	Date
	1 7	Crown
	30
20	10	15
	9	I	II
	8
	7
	6
	0 3
	30
20	10	15
	9	I	II
	8
	7
	6

Setting the date/time following a battery change

Example:
– Date / time on the watch:	17	/ 1:25 AM
– Present date / time:		/ 8:30 PM
	04

Pull out the crown to position II (the watch continues to run).

Turn the crown until yesterday’s date appears 03 .

Second hand

	0 3
	30
20	10	15
	9	I
	8
	7
	6

	0 4
	30			60
20	10		45	15
				30
	9	10	1	I
	8		2
	7		3
	6	5	4

**Pull out the crown to position III

(the watch stops).

II	III		**Turn the crown until the correct date
				04	appears.
			**Continue to turn the crown until the
			correct time 8:30 PM appears.
			**Push the crown back into position I.
			Please note:
II	III		**To set your watch to the exact second,
			please refer to the chapter entitled «setting

the time».

**Please observe the AM/PM clock rhythm.