Roland DTS-30S Owner's Manual
BEACHTEN SIE IMMER FOLGENDES
English
PAD STAND
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s) where it will be available for immediate
reference.
PDS-20
Owner’s Manual
USING THE UNIT SAFELY
IMPORTANT NOTES
Placement
• Depending on the material and temperature
of the surface on which you place the unit, its
rubber feet may discolor or mar the surface.
Functions Setup
Mounting plate
Attach this to the product before
attaching to the stand
Clamp
Attach the mounting
plate to the stand
1. Adjust the spread of the tripod.
* Use the stand with the tripod spread out to
stabilize the stand.
2. Adjust the stand’s height.
Angle adjustment knob
Adjust the tilt of the
mounted product
Clamp knob
Fastening/removing the
mounting plate
Height adjustment knob
Adjust the stand height
Tripod adjustment knob
Adjust the tripod spread
* Use this stand so that the top surface of the
mounted product is no higher than 1 meter
(3’ 3” inches) above the oor.
When the upper surface of the mounted
product is at a height of less than 75 cm
(2’ 5” inches) from the oor (with the product
already attached to the stand)
Open the tripod so that the distance between
each leg (at the oor) is approximately 50 cm
(1’ 7” inches).
When the upper surface of the mounted
product is at a height of 75 cm (2’ 5” inches)
or greater above the oor (with the
product already attached to the stand)
Open the tripod to the fullest extent.
3. Use screws to attach the mounting
plate to the product. The screws are
attached to the bottom surface of the
product (four locations).
* When attaching the product to the mounting
plate, do not use any screws other than
those that are included with the product. The
product might be damaged if you use other
screws.
4. Attach the mounting plate to the
stand.
Insert the mounting plate into the clamp, then
turn the clamp knob to secure the mounting
plate.
Regarding Compatible Products
For details on Roland products that are compatible with
this stand, refer to the support information on the Roland
website.
http://roland.cm/pds-20_cp
5. Turn the angle adjustment knob
to adjust the tilt of the mounted
product.
* If you loosen this excessively, the part might
come o or the product might fall down.
Clamp
WARNING
Do not disassemble or modify by yourself
Do not carry out anything unless you
are instructed to do so in the owner’s
manual. Otherwise, you risk causing
malfunction.
Do not repair or replace parts by yourself
Be sure to contact your dealer, a Roland
service center, or an ocial Roland
dealer.
For a list of Roland service centers and
ocial Roland dealers, refer to the Roland website.
Do not use or store in the following types of
locations
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle,
near a heating duct, on top of heatgenerating equipment); or are
• Damp (e.g., baths, washrooms, on wet
oors); or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness;
or are
• Placed in a poorly ventilated location.
Do not place in an unstable location
Otherwise, you risk injury as the result
of the unit toppling over or dropping
down.
Be cautious to protect children from injury
Always make sure that an adult is
on hand to provide supervision and
guidance when using the unit in places
where children are present, or when a
child will be using the unit.
Do not drop or subject to strong impact
Otherwise, you risk causing damage or
malfunction.
CAUTION
Use this stand only for specic Roland products
This stand for use only with specic
Roland musical instruments. See
apparatus instructions. Use with other
models is capable of resulting in
instability causing possible injury.
Evaluate safety issues before using stands
Even if you observe the cautions given
in the owner’s manual, certain types of
handling may allow this product to fall
from the stand, or cause the stand to
overturn. Please be mindful of any safety issues
before using this product.
Avoid climbing on top of the unit, or placing
heavy objects on it
Otherwise, you risk injury as the result of
the unit toppling over or dropping down.
Take care so as not to get ngers pinched
When setting up or storing this stand,
take care not to pinch your ngers.
Whenever a child uses the unit, an adult
should be on hand to provide supervision
and guidance.
• Clamp
• Angle adjustment section
• Tripod spread adjustment section
• Height adjustment section
Keep small items out of the reach of children
To prevent accidental ingestion of the
parts listed below, always keep them out
of the reach of small children.
• Removable Parts
Knobs, washer
Maintenance
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility of
discoloration and/or deformation.
Additional Precautions
• When disposing of the packing carton or
cushioning material in which this unit was
packed, you must observe the waste disposal
regulations that apply to your locality.
Intellectual Property Right
• Roland is either registered trademarks or
trademarks of Roland Corporation in the United
States and/or other countries.
• Company names and product names appearing
in this document are registered trademarks or
trademarks of their respective owners.
* Do not insert your ngers inside the stand pipe. This may result in injury.
* Take care not to hit your face or head against any of the stand’s protruding components (knobs, mounting plate, etc.).
* When you loosen the knob while making adjustment of each parts, the pipe, product and clamp knob etc. might fall and pinch your ngers. The product might
be damaged if it falls. Use one hand to support the tom, pipe, or cymbal mount while you slowly loosen the knob.
* To prevent the stand from tipping over or falling, tighten the knobs until there is no looseness.
* This document explains the specications of the product at the time that the document was issued. For the latest information, refer to the Roland website.
© 2020 Roland Corporation
Loading...