TRR01
Resistors
Sulfur Tolerant Chip Resistors
TRR01 (0402 size)
zFeatu res
1) Unique protect materials prevent from silver sulfide occurrence under sulfur enviromnet.
2) Highly recommended for automotive, industrial and Power supp ly applications under su lfur environ ment.
3) Realize the good cost performance not like the Au terminal components.
4) ROHM resistors have approved ISO9001 / ISO/TS 16949 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the
product before using or ordering it.
zRatings
Item Conditions Specifications
Rated power
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
60
40
POWER LOAD (%)
20
0
−55 0 70 100 155
AMBIENT TEMPERATURE (°C)
Fig.1
0.063W (1 / 16W)
C
at 70°
Rated voltage
Nominal resistance See Table 1.
Operating temperature
The voltage rating is calculated by the following equation.
If the value obtained exceeds the limiting element voltage,
the voltage rating is equal to the maximum operating voltage.
E= P×R
E: Rated voltage (V) P: Rated power (W)
R: Nominal resistance (Ω)
Limiting element voltage 50V
−55°C to +155°C
Jumper type
Resistance
Rated current
Operating temperature
zBefore using components in circuits w here they will be exposed to transients such as pulse loads (short–duration, high– level l oads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state volt age that
is greater than its rated voltage.
Max. 50mΩ
1A
−55°C to +155°C
Table 1
Resistance tolerance
J (±5%)
F (±1%)
Resistance range
(Ω)
1.0 to 9.1
10 to 2.2M
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm/°C)
+
500 / −250
±20010 to 10M
±100
Rev.A 1/4
Resistors
z
Characteristics
Item Test conditions (JIS C 5201-1)
Resistance
TRR01
Guaranteed value
Resistor type
J : ±5%
F : ±1%
Jumper type
Max. 50mΩ JIS C 5201-1 4.5
Variation of resistance
with temperature
Overload
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
See Table.1
± (2.0%+0.1Ω) Max. 50mΩ
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
± (1.0%+0.05Ω)
No remarkable abnormality on the appearance.
± (1.0%+0.05Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (3.0%+0.1Ω)
± (1.0%+0.05Ω)
± (1.0%+0.05Ω)
Without mechanical damage such as breaks.
Max. 50mΩ
Max. 50mΩ
Max. 100mΩ
Max. 100mΩ
Max. 100mΩ
Max. 50mΩ
Max. 50mΩ
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum overload voltage : 100V
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. : −55
JIS C 5201-1 4.24
°C, 93%RH
40
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
°C
155
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
°C
, Immersion cleaning, 5±0.5min.
23±5
Solvent : 2-propanol
JIS C 5201-1 4.33
°C
to +125°C 5cyc
°C
°C
°C
Rev.A 2/4
Resistors
3
0
5
0
5
5
zDimensions (Unit : mm)
TRR01
①
0.3 ± 0.2
0.25 ＋ 0.0
-0.1
0.33 ± 0.08
0.4 ± 0.1
1.0 ± 0.05
1.6 ± 0.1
②
④
③
⑤
⑥
.0
⑧
5 ±
0.45 ± 0.1
⑦
0.
.0
0.5 ±
0.8 ± 0.1
z
Packaging
Reel Taping
ABD
0 2
0 4
0 6
0 2
0 4
0 6
0 8
0 8
No.
1
Silver thick film electrode
2
Resistive element
3
Over coating
4
Protection electrode
5
Silver thick film electrode
6
Nickel electrode
7
Sn electrode
8
Alumina substrate
P
A
0
B
0
Material
P0
2
φD
0
E
F
W
P
1
Heat crimp cover tape
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
ABCD
φ180
0
−1.5
φ60
+1
+1.0
9
0
±0.2
φ13
0
Thick paper
mount
(Underside paper tape)
WFEA0B
8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.1
D
0
P
+0.1
φ1.5
4.0±0.1 2.0±0.052.0±0.05
0
Chip resistor Square punchout hole
0
P
1
(Unit : mm)
P
2
Max. 1.1
2
T
0
T
2
Rev.A 3/4
Resistors
zPart No. Explanation
TRR01
RTR0 PMZ J
Part No. Nominal resistance
Packaging Specifications Code
Part No.
TRR01
Reel (φ180) : JEITA ET-7200B
: Standard product
Code
MZP
Resistance tolerance
±
5%)
J(
FX(±1%)
1
Resistance tolerance
F±1%
±
5%
J
J is also used
for jumper
Packaging specifications Reel
Paper tape (2mm Pitch)
Resistance code, 3 or 4 digits.
000 denotes jumper type.
Resistance
tolerance
Resistance
FJ::4 digits
code
3 digits
φ
180mm (7inch)
Basic ordering unit (pcs)
10,000
Rev.A 4/4
Appendix
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
CO.,LTD.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account when
designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples of
application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or
exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility
whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or
devices (such as audio visual equipment, office-automation equipment, communication devices, electronic
appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes effor ts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no
responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended
to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Notes
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2008 ROHM CO.,LTD.
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev3.0
Loading...