ROHM MCR01MZPD Technical data

A

l

Thick Film Chip Resistors

MCR Series < Automotive >

Features

1) Full line up from ultra small size (01005) to 2512 with jumper type.

2) High reliability metal glazed thick film.

3) ROHM resistors have obtained ISO9001/ISO/TS16949 certification.

4) "Automotive" product is AEC-Q200 compliant.

Part No.

MCR004

(mm)

0402

Size

(inch)

01005 10Ω to 3MΩ

GENERAL PURPOSE

Type Code

AUTOMOTIVE

∗Corresponds to

AEC−Q200

YZP 15,000

RZP

Resistance Range

−

−

Packing

Specification

Paper tape

(2mm pitch)

Embossed tape

(1mm pitch)

Quantity / Ree

40,000

MCR006

MCR01

MCR03

MCR10

MCR18

MCR25

MCR50

MCR100

0603

1005

1608

2012

3216

3225

5025

6432

0201

0402

0603

0805

1206

1210 JZH

2010

2512

YRT

MRT

ERT

ERT

ERT

JZH

JZH

YZP

MZP

EZP

EZP

EZP

∗Please contact us for status of AEC-Q200 on "General purpose" products.

Part Number Description

06

CMR

Part No.

MCR

(Micro chip resistors)

Size

004 (0402 [01005])
006 (0603 [0201])
01 (1005 [0402])
03 (1608 [0603])
10 (2012 [0805])
18 (3216 [1206])
25 (3225 [1210])
50 (5025 [2010])
100 (6432 [2512])

0 YTR

(mm [inch])

Type Code

Resistance Tolerance Nominal Resistance

D ( ±0.5% )
F ( ±1% )
FX ( ±1% )
J ( ±5% )

∗Only MCR03EZP

(Including jumper type)

1Ω to 10MΩ

1Ω to 10MΩ

1Ω to 10MΩ

1Ω to 10MΩ

1Ω to 10MΩ

1Ω to 3.3MΩ

1Ω to 560kΩ

1Ω to 100kΩ

Paper tape

(2mm pitch)

Paper tape

(4mm pitch)

Embossed tape

(4mm pitch)

J01 0

Resistance code, 3 or 4 digits.
000 denotes jumper type.

Resistance

tolerance

D,FJ::4 digits

Ex.)
1Ω = 1R0 ( ±5% )

9.1 Ω = 9R1 ( ±5%
10 Ω = 10R0 ( ±0.5%,±1% )
100 ( ±5% )

2.2M Ω = 2204 ( ±1% )
225 ( ±5% )

Resistance

code

3 digits

15,000

10,000

5,000

4,000

)

www.rohm.com

1/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

2012.03 - Rev.

A

Products List

Rated Power

Type Code

MCR006

YZP

MCR01 MZP

MCR03

EZP

(70

0.05 25

0.063

0.125

MCR10

EZP

0.25

MCR18

EZP

0.125

MCR25

JZH

0.25

JZHMCR50

MCR100

JZH

∗Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product

before using or ordering it.

°C)

(W)

0.1

0.1

0.5

1

Limiting Element

Voltage

(V)

50

50

150

200 400

200

200 400

200 400

−

Temperature

Coefficient
(ppm / °C)

+600 / −200

±250
±250
±200
±100

Resistance

Tolerance

(%)

J(±5%)
F(±1%)
D(±0.5%)

Resistance Range SeriesPart No.

Maximum

Overload

Voltage

(V)

Jumper type : Rmax = 50m Ω / Imax. = 0.5A

−

+500 / −250

±200
±100
±100

±50

J(±5%)
F(±1%)
D(±0.5%)

Jumper type : Rmax = 50m Ω / Imax. = 1A

100

±400
±200
±100
±100

±50

J(±5%)
FX(±1%)
D(±0.5%)

Jumper type : Rmax = 50m Ω / Imax. = 1A

200

300

±400
±200
±100
±100

±50

J(±5%)
F(±1%)
D(±0.5%)

Jumper type : Rmax = 50m Ω / Imax. = 2A

±400
±200
±100
±100

±50

J(±5%)
F(±1%)
D(±0.5%)

Jumper type : Rmax = 50m Ω / Imax. = 2A

500±350

400

±500
±200

J(±5%)

F(±1%)

Jumper type : Rmax = 50m Ω / Imax. = 2A

500±350

±500
±200
±350
±100

J(±5%)

F(±1%)

Jumper type : Rmax = 50m Ω / Imax. = 3A

500±350

±500
±350
±200
±100

J(±5%)

F(±1%)

Jumper type : Rmax = 50m Ω / Imax. = 4A

1.0Ω to 9.1Ω
10Ω to 10MΩ
10Ω to 10MΩ

10Ω to 910Ω

1kΩ to 1MΩ

1.0Ω to 9.1Ω
10Ω to 10MΩ

10Ω to 2.2MΩ

10Ω to 91Ω

100Ω to 1MΩ

1.0Ω to 9.1Ω
10Ω to 10MΩ
10Ω to 10MΩ

10Ω to 91Ω

100Ω to 1MΩ

1.0Ω to 9.1Ω
10Ω to 10MΩ

10Ω to 2.2MΩ

10Ω to 91Ω

100Ω to 1MΩ

1.0Ω to 9.1Ω
10Ω to 10MΩ

10Ω to 2.2MΩ

10Ω to 91Ω

100Ω to 1MΩ

1.0Ω to 2.0Ω

2.2Ω to 5.1Ω

5.6Ω to 3.3MΩ
10Ω to 1MΩ±100

1.0Ω to 2.0Ω

2.2Ω to 9.1Ω

10Ω to 330kΩ

360kΩ to 560kΩ

10Ω to 180kΩ

1.0Ω to 2.0Ω

2.2Ω to 9.1Ω
10Ω to 22Ω

24Ω to 100kΩ

10Ω to 82kΩ

E24
E24
E24
E24
E24

E24
E24

E24,E96

E24
E24

E24
E24

E24,E96

E24
E24

E24
E24

E24,E96

E24
E24

E24
E24

E24,E96

E24
E24

E24
E24
E24

E24,E96

E24
E24
E24
E24

E24,E96

E24
E24
E24
E24

E24,E96

Data Sheet MCR series < Automotive >

Operating

Temperature

Range

(°C)

−55 to +125

−55 to +155

−55 to +125

www.rohm.com

2/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

2012.03 - Rev.

A

(Unit : mm)

Chip Resistor Dimensions and Markings

<Marking method>
There are three or four digits used for the calculation number

a

according to IEC code and “R”is used for the decimal point.

b

Marking method of jumper type

Jumper type
MCR006 / 01 / 25 / 50 / 100
MCR03 / 10 / 18

Marking method of MCR03
For MCR03 series resistors, the printing process restricts the marking to three digits/characters.
Consequently, 1% tolerance resistors with values from the E24 series will be marked the same as
5% resistors with the same value, but 1% tolerance resistors with values from the E96 series will not be marked.

Examples:

MCR03EZPJ243 (5% tolerance, E24 / 24 k  ) Marking = 243

MCR03EZPFX2402 (1% tolerance, E24 / 24 k  ) Marking = 243

MCR03EZPFX2432 (1% tolerance, E96 / 24.3 k  ) No Marking

MCR18EZPJ243 (5% tolerance, E24 / 24 k  ) Marking = 243

MCR18EZPF2402 (1% tolerance, E24 / 24 k  ) Marking = 2402

MCR18EZPF2432 (1% tolerance, E96 / 24.3 k  ) Marking = 2432

Land pattern Example

C

L

103

W

t

Part No. Type Code (mm) (inch) L W t a b

MCR006

MCR01
MCR03
MCR10
MCR18
MCR25
MCR50

MCR100

YZP 0603 0201
MZP 1005 0402
EZP 1608 0603
EZP 2012 0805
EZP 3216 1206
JZH 3225 1210
JZH 5025 2010
JZH 6432 2512

Marking existence

No

Yes

B

D

A

0.6±0.03 0.3±0.03 0.23±0.03 0.1±0.05 0.15±0.05

1.0±0.05 0.5±0.05 0.35±0.05 0.2±0.1

1.6±0.1 0.8±0.1 0.45±0.1 0.3±0.2 0.3±0.2

2.0±0.1 1.25±0.1 0.55±0.1 0.4±0.2 0.4±0.2

3.2±0.15 1.6±0.15 0.55±0.1 0.5±0.25 0.5±0.25

3.2±0.15 2.5±0.15 0.55±0.15 0.5±0.25 0.5±0.25

5.0±0.15 2.5±0.15 0.55±0.15 0.6±0.25 0.6±0.25

6.3±0.15 3.2±0.15 0.55±0.15 0.6±0.25 0.6±0.25

0.25

Land

Dimensions

Part No.

MCR006

MCR01
MCR03
MCR10
MCR18
MCR25
MCR50

MCR100

Type Code A

YZP
MZP
EZP
EZP
EZP
JZH
JZH
JZH

0.3

0.5

0.5

1.2

2.2

2.2

3.8

5.1

B

0.84

1.3

1.3

2.6

4.0

4.0

6.0

8.1

(Unit : mm)

+0.05

−0.1

C

0.3

0.5

0.5

1.15

1.5

2.3

2.3

3.0

Data Sheet MCR series < Automotive >

Marking

existence

D

0.27

0.4

0.4

0.7

0.9

0.9

1.1

1.5

No
No

Yes ∗

Yes
Yes
Yes
Yes
Yes

www.rohm.com

3/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

2012.03 - Rev.

A

8
8

Derating Curve

When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.



MCR006 / 100

100

80

60

40

20

PERCENT RATED POWER (%)

0

−55 0 70 100 125

AMBIENT TEMPERATURE (°C)

Characteristics

Test Items Test Conditions

Guaranteed Value

Resistor Type

Jumper Type



MCR01 / 03 / 10 / 18 / 25 / 50

100

80

60

40

20

PERCENT RATED POWER (%)

0

−55 0 70 100 155

AMBIENT TEMPERATURE (°C)

Data Sheet MCR series < Automotive >

Resistance

Variation of resistance
with temperature

Overload

Solderability

Resistance to
soldering heat

Rapid change of
temperature

Damp heat, steady state

Endurance at 70°C

Endurance

See P.1

See P.1

± (2.0%+0.1Ω) Max. 50mΩ

A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.

± (1.0%+0.05Ω)

Max. 50mΩ

No remarkable abnormality on the appearance.

± (1.0%+0.05Ω)

± (3.0%+0.1Ω)

± (3.0%+0.1Ω)

± (3.0%+0.1Ω)

Max. 50mΩ

Max. 100mΩ

Max. 100mΩ

Max. 100mΩ

20

°C

Measurement : +20 / −55 / +20 / +125°C

Rated voltage (current) ×2.5, 2s.
Limiting element voltage ×2 : (See P.1)

Rosin·Ethanol (25%WT)
Soldering condition : 235±5

°C

Duration of immersion : 2.0±0.5s

Soldering condition : 260±5

°C

Duration of immersion : 10±1s

Test temp.

−55

°C

to +125°C 100cyc (MCR006 / 01 / 03)

°C

to +125°C 5cyc (MCR10 / 18 / 25 / 50 / 100)

−55

40°C, 93%RH
Test time : 1,000h to 1,048h

70°C
Rated voltage (current)

1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h

125°C (MCR006 / 25 / 50 / 100)
155°C (MCR01 / 03 / 10 / 18)
Test time : 1,000h to 1,048h

°C

, Immersion cleaning, 5±0.5min

Resistance to solvent

Bend strength of
the end face plating

± (1.0%+0.05Ω)

± (1.0%+0.05Ω)

Max. 50mΩ

Max. 50mΩ

Without mechanical damage such as breaks.

23±5
Solvent : 2−propanol

−

Compliance Standard(s) : IEC60115−

JISC 5201−

Technical data

Fit

MCR006

YZP

1000 1000 1000 1000

0.0016

0.157

Parameter Unit

Insulation
resistance

MΩ

Failure rate

Weight

www.rohm.com

4/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

mg/pc

MCR01

MZP

0.0002

0.70

MCR03

EZP

0.0009

2.12

MCR10

EZP

0.0015

5.03

MCR18

EZP

1000

0.0018

9.46

MCR25

JZH

1000

0.0203

16.5

MCR50

JZH

1000

0.0201

25.8

MCR100

JZH

1000

0.0586

42.0

2012.03 - Rev.

A

W

B

)

)

Tape Dimensions



Paper Tape

P

0

P

2

P

1

Data Sheet MCR series < Automotive >

(Unit : mm

φD

0

E

F

B

0

W

WType CodePart No. F E A

8.0±0.2MCR006 YZP 3.5±0.05 1.75±0.1

8.0±0.3MCR01 MZP 3.5±0.05 1.75±0.1

0

B

0

0.38±0.03 0.68±0.03

0.7±0.1 1.2±0.1

A

0

Top tape

ase paper

(Bottom tape)

Components Cavity

2

T

Type CodePart No. P

MCR006 YZP

MCR01 MZP

MCR03 EZP

MCR10 EZP

MCR18 EZP



Embossed Tape

P

0

P

2

0

φD

E

8.0±0.3MCR03 EZP 3.5±0.05 1.75±0.1

8.0±0.3MCR10 EZP 3.5±0.05 1.75±0.1

8.0±0.3MCR18 EZP 3.5±0.05 1.75±0.1

D

φ1.5

φ1.5

φ1.5

φ1.5

φ1.5

0

+0.1

0

+0.1

0

+0.1

0

+0.1

0

+0.1

0

0

4.0±0.1

4.0±0.1

4.0±0.1

4.0±0.1

4.0±0.1

P

2.0±0.05

2.0±0.05

4.0±0.1

4.0±0.1

4.0±0.1

WType CodePart No. F E A

8.0±0.3MCR25 JZH 3.5±0.05 1.75±0.1

F

0

B

A

0

P

1

T

2

12±0.3MCR50 JZH 5.5±0.05 1.75±0.1

12±0.3MCR100 JZH 5.5±0.05 1.75±0.1

1.1±0.1 1.9±0.1

1.65

1.95

1

2.0±0.05 Max 0.5

2.0±0.05

2.0±0.05

2.0±0.05

2.0±0.05

3.0±0.1 3.5±0.1

3.4±0.2 5.6±0.2

3.5±0.2 6.7±0.2

+0.2

−0.1

+0.1

−0.05

P

2

0

2.4

3.5

Max 1.1

Max 1.1

Max 1.1

Max 1.1

(Unit : mm

+0.2

−0.1
+0.15

−0.05

T

2

B

0

D

φ1.5

φ1.5

φ1.5

0

+0.1

0

+0.1

0

+0.1

0

0

4.0±0.1

4.0±0.1

4.0±0.1

P

1

4.0±0.1

4.0±0.1

4.0±0.1

P

2

T

2

2.0±0.05 Max 1.1

2.0±0.05

2.0±0.05

Max 1.1

Max 1.1

Type CodePart No. P

MCR25 JZH

MCR50 JZH

MCR100 JZH

www.rohm.com

5/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

2012.03 - Rev.

A

)

Reel Dimensions

ABD

Data Sheet MCR series < Automotive >

0 2

0 4

0 6

0 2

0 4

0 6

0 8

0 8

C

Label

ACCORDING EIAJ ET-7200B

(Unit : mm

AType CodePart No. B C D

MCR006

MCR01
MCR03
MCR10
MCR18
MCR25
MCR50

MCR100

YZP

MZP

EZP
EZP
EZP
JZH
JZH
JZH

φ180

0

−1.5

φ60

+1.0

0

9

13

+1.0

0

φ13±0.2

+1.0

0

www.rohm.com

6/6

c

○

2012 ROHM Co., Ltd. All rights reserved.

2012.03 - Rev.

Notes

No copying or reproduction of this document, in par t or in whole, is permitted without the
consent of ROHM Co.,Ltd.

The content specied herein is subject to change for improvement without notice.

The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.

The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.

The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu­nication devices, electronic appliances and amusement devices).

The Products specied in this document are not designed to be radiation tolerant.

While ROHM always makes effor ts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injur y (such as a medical
instrument, transportation equipment, aerospace machiner y, nuclear-reactor controller, fuel­controller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.

Notice

www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.

Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

R1120A