with the unit. Please consult with your nearest repair center.
Warning:
When
existing fuse. The use of a varying type or rating may cause serious
damage to the unit.
replacing the fuse,
be
BLACK
GROUND(-)
RED
UP
IGNITION SWITCH
GREY+
FRONT
(B+)
RIGHT
SPEAKER
VIOLET+
REAR
RIGHT
VIOLET/BLACK-
SPEAKER
power connections and
a fuse
blows
after replacement, you may have
sure to use the same type and rating
replace
of
the
Be sure your wire remote(RFX-MR8/RFX-MR6.5)
wrong
connection will
is
installed
correctly,
cause serious damage to the wire remote.
P3
Page 5
INSTALLATION
1 Precautions
interfere with normal
Carefully
driving functions
Avoid
high temperatures, including direct sunlight, engine compartment heat and engine
exhaust.
choose a mounting location so that
the vehicle.
of
be subjected to excessive vibration, dirt and
installing
the unit where it
will
the unit will
not
Use only the supplied mounting hardware for a safe and secure
2 Mounting
Correct
Incorrect
illstration
mounting
facing
Better:
45
mounting
positions
upward
positions
Best:
installation.
facing
90
upward
Installation
3
Use the enclosed nylon
wire tie-downs to hold down the wire harness will aid
along
the wires and into the unit.
Note
wire tie-downs (wire
either
Do not mount the black box
position shown. Doing so will allow
water to travel inside the unit causing
damage.
clamps) for additional support. Using the
P4
in
preventing water from migrating
in
Page 6
BASIC OPERATION
Power -ON/OFF
Press this button to turn unit
SEL - Function Select Button
Press the "SEL" button repeatedly to scroll through the functions
> SUB > DSP > ID3 > VOL. Once desired function
to change the setting value.
Press and hold the SEL button to enter zone selections. Short press the SEL button
repeatedly to scroll through the
(1)
ON
or OFF.
(2)
BAS>
is
selected, use the VOL buttons
TRE
>FAD
Zone: America/China/Europe
Beep: Activates Beep On/Off
Clock: 12/24 hour format
TRI
1: Activates Trigger 1 On/Off (Switched 12V). This trigger is set to "ON" by default.
TRI2:
reactivated if unit is disconnected from power source.
VOL - Volume Up/Down
Press the UP arrow button to turn the volume up to the desired listening level.
Press the DOWN arrow button to turn the volume down to the desired listening level.
MODE button
Short press the "MODE" button to switch through modes: FM/AM > AUX1 > AUX2 >
SIRIUS > BT > USB > SD > CDC
Activates Trigger 2 On/Off (Switched 12V). This trigger will need to be
(3)
(4)
DISP-
Press the "DISP" button to toggle the system time On/Off on the LCD.
Display Button
(5)
Adjusting Time (Clock)
Press and hold the "DISP" button until the hour digit starts to blink, use the
to adjust hour. Once hour
~~~
buttons.
Adjusting
Press the "MENU" button for more the 2 seconds to adjust the backlight brightness
on the LCD.
Low
Voltage Warning
When the vehicle's power supply drops below 10 volts, the LCD will display
"BATTERY LOW" and the system will beep for 1 minute. The black box will turn off
automatically after the 1 minute period.
backlight-
(25°/o, 1 00°/o)
is
set, press "DISP" again to adjust minute using the ~ ....
MENU
(16)
~~~I~~~
~I
Locking the Control Panel
To lock the RFX-MR5BB control panel, press and hold "SEL" and "DISP" buttons
simultaneously for 3 seconds. The black box will not respond when button are pressed
on the control panel. Press and hold "SEL" and "DISP" buttons for 3 seconds to unlock
the control panel.
PS
Page 7
SiriusXM®
Only
SiriusXM® brings you more
including commercial-free music
Welcome
more information, visit www.siriusxm.com."
Activating
After installing
select
cannot hear the preview channels,
SiriusXM
to
your
SiriusXM mode. You
Connect
OPERATION
the
world
of
satellite radio. A SiriusXM
SiriusXM subscription:
your
SiriusXM
tuner is properly
Connect Vehicle
should
of
what you
plus
the best sports, news, talk,comedy and entertainment.
be
able
to hear the SiriusXM preview
please
check the
installed.
love
to
listen
to, all
in one
Vehicle
Tuner and antenna, power on
installation
Tuner and Subscription are required. For
instructions to make sure
place. Get over
channel
your
RFX6000
on
Channel1.
150
channels,
and
your
If
you
After you can hear the Preview channel, tune
need this number
Note: the SiriusXM Radio
In the
USA,
e
Visit www.siriusxm.com/activatenow
e
Call
SiriusXM Listener
For
Canadian
e
Visit www.siriusxm.ca/activatexm
e
Call
XM
Note, the activation process
will
need
to
MODE
•
Short
Note:
connect
(4)
Mode Selection
press
If
there is no SiriusXM TUNER connected this mode will be skipped. Please
your
to
activate your subscription. Write the number down
ID
does
not
include the
you can activate
Subscriptions,
customer
be
powered on and receiving the SiriusXM
MODE
button to select SiriusXM mode.
online
Care
at 1-866-635-2349
please
Care
at 1-877-438-9677
usually takes
or
by calling SiriusXM Listener care:
contact:
SiriusXM Tuner to the SiriusXM port located at the back
to
Channel 0 to find the Radio
10
to
letters
15
I,
0,
minutes, but may take up to
signal
Then press MODE button to change to SiriusXM mode.
ID
of
your tuner. You
for
reference.
S
or
F.
an
hour. Your radio
to
receive the activation message.
of
the unit.
will
DISP(5)
• Display
Short
press
Mode
DISP
Selection
button repeatedly to switch different
display
mode.
You
can choose
betweenChannel
Channel
Category
Artist
Song
Content
NumberName-
Name-
Name-
Title-
Info-
CH/
CHANNEL/
CATEGORY/
ARTIST/
SONG/
INFO/
&(repeat)SEEK+ /SEEK- (6)
e
Channel
Browsing
When the Category Browsing mode is off, short press the buttons to start browsing
all
channels. Press the
Press the
SEL
key to select the channel showed on LCD and play it.
pressed in 5s, the LCD
information again.
SEEK+/SEEK-
will
change back to display current playing channel
key to browsing next/previous channels,
P6
If
there is no key
Page 8
SiriusXM OPERATION
• Category Browsing
In
the Category Browsing mode, short press the buttons to
in
current
Press the SEL key to select the channel showed on LCD and play it. If there is no key
category. Press the
SEEK+/SEEK-
key to browsing next/previous channels,
start
browsing channels
pressed in 5s, the LCD will change back to
information again.
display
current playing channel
e Rapid Channel Browsing
When the
channel browsing mode, you can browsing all channels in
the touch key, the LCD will show the information
the SEL key to
pressed in 5s, the LCD will change back to
information again.
• Category Selection
In
the Category Browsing mode, long press and hold the buttons over 2S to select
previous/next
AS.PS (7)
Category
select
category
Browsing mode is off, press and hold the buttons goes into rapid
higher
of
the last browsed channel. Press
the channel showed on LCD and play it. If there is no key
without
display
press SEL key.
current playing channel
speed,
if
you release
e Direct Channel Tuning
Short press this button, the
the Volume up and down buttons to select
first
character
of
the channel
number
number
0-9 and press SEL key to enter
will flash. Press
then the second
After
select
the last number, press SEL key to
character
flash. Use the same operation to select third character.
enter
and play the selected channel.
BAND (8)
• Banks Selection
In
SiriusXM mode, short press this button to change the bands. The current bands
in
will change
PRESET 1-6
the following order:
(1
0/11/12/13/14/15)
SXM1-SXM2-
SXM3
• Store Preset Channel
Long press a PRESETS button, the
corresponding preset number will
be used to store 6 channels
your
access to
favorite channels.
in
current
appear
each bands(SXM1, SXM2, and SXM3)
channel will be stored, and the
in
the display. The PRESETS buttons can
for
convenient
e Recall Preset Channel
To
recall a preset channel,
Presets button and the unit will turn to the corresponding stored channel.
select
a band
of
channels
(if
needed).Short
press a
P7
Page 9
SiriusXM
OPERATION
SCAN(9)/MENU
• Channel
Short
press SCAN
every 5 seconds per channel until you press the
(16)
Scanning
button to scan
all
the channels. The unit
SCAN
will
keep on scanning
button again to stop scan
function.
• Channel
Short
press MENU button to
screen
will
show.
PARENTAL
You can
your
permission. The
execute the
to resume the
e
GUIDE ON HOW TO
Category
Mode
enter
category mode while
field, when short press again, the
CONTROL
lock
any SiriusXM channels you do not
default
default
default
reset operation or
code.
ENTER THE
code is
"5220".
disconnect
CODE USING
category
want
In
case you forget
"CAT ON" will
setting
will
be off, and
others to have access
your
the unit
THE
completely
VOLUME BUTTON
show
in the
"CAT OFF"
without
code please
from the battery
When the first character is flashing, Press the Volume up and down buttons to
5 and press
SEL
key to
enter
then the second
character
flash. The same operation to
select
select the rest
e
TO
LOCKA
Select
will
a
channel that you wish to lock then long press
show on the display. Enter the code then press
Locked" will
e
TO ACCESS
You can access a
requested to
Nme/Song
without enter the pass code.
e
TO
Select
Title/Content Info) would
UNLOCKACHANNEL
the
"UNLOCK CH" will
-
"Channel Unlocked" will show on the
e
TO
CHANGE THE CODE
Press and
code then press
new code then press
e
LOCKEDCHANNELMANAGEMENT
character
"2", "2", "0".
When done, press
CHANNEL
show
on the
display
A LOCKED CHANNEL
locked channel by
enter
the passcode before access the
channel
not
allow
browsing method
to
be
locked channel that you wish to unlock then
show on the display. Enter the code then press
display
hold MENU Button
SEL to confirm
-"OLD
-"NEW
CODE" will
CODE" will
SEL again to confirm
SEL
key
to confirm.
SCAN
SEL
key
or
locked channel. The content metadata(Artist
displayed
when you browse
long
button
to confirm
direct tunning method, you are
press SCAN
-"CH
-"Channel
to
a
locked channel
button-
SEL
key
LOCKED"
to confirm
show on the display. Enter the old
show
-"SETCODE
on the display. Enter
OK" will
show on the display.
your
When you
and
"1"
want
button
to browse
simultaneously
browse the entire locked channel by pressing the
entering the correct passcode.
want to
Mature channels ,
"CLEAR ALL
clear
that
locked channel.
just
press the Volume up and down buttons
LOCKED"
display, then
all
the locked channels, press and
to
enter
the locked channel browsing mode.
Volume
Select
a locked channel and press
To
clear all
P8
the locked channels except the
hold "MODE"
button
You
up and down buttons
SEL
key
if
you
enable
until
the advisory
can
after
Page 10
SiriusXM
OPERATION
press the Enter button to execute.
of
the mature
the advisory
MODE(4)
channels,
you
just
press the Volume
"LOCK/UNLOCK MATURE"display, press the SEL
+
BAND(8)
• Default Reset
In
SiriusXM mode, press and
mode to the factory default
channels will
storing
will be
be
unlocked,
cleared,
the
hold
setting. When
the mature channels will
parental control
passcode, etc.
TROUBLESHOOTING
PROBLEM
SiriusXM
selected
Check
message
Check
message
No
in
Channel
SiriusXM
Tuner
Antenna
Signal
SiriusXM
C
Display
Not
mode
can
C
Display
in
SiriusXM
C
in
SiriusXM
C
Display
mode)
Subscribed
message
mode)
not
mode)
Display
mode)
message
in
be
CAUSE CORRECTIVE ACTION
If
you want to change the enable/disable
up and down buttons
status
until
key to switch.
BAND and MODE button to reset the SiriusXM
finished the reset operation, the
locked
be unrestrained, the presets
passcode
will
be resumed to
Make
sure
to
USA
AREA
setting
Check
connection
cable
SiriusXM
Check
wire
bends.
necessary.
remains,
have
The
and
clear
sky.
must
outside
best
Current
your
SiriusXM
-
-
the
unit to
correctly
Ensure
ensure
is
the
for
Replace
been
vehicle
the
view
The
be
reception.
channel
subscription
In
the
In
Canada
SiriusXM
on
connected.
the
SiriusXM
connected
tuner
SiriusXM
breaks
If
the
damaged.
antenna
of the
magnetic
mounted
of the
to
subscribe:
USA
call
choose
in
tuner
the
that it's
the
antenna
must
vehicle
call
the
region
tuner
back
antenna
to the
correctly.
antenna
or
sharp
the
antenna
message
may
be
outside,
must
have
southern
antenna
on
the
for the
not
included
package.
1-866-635-2349
1-877-438-9677
default
of the
if
a
in
Call
pg
Page 11
SiriusXM OPERATION
TROUBLESHOOTING
Channel
C
SiriusXM
Channel
message
Subscription
message
Not
Display
message
mode)
Locked C Display
in
in
Available
SiriusXM
Updated(
SiriusXM
in
mode)
Display
mode)
This
channel
SiriusXM
channel
entered
channel
the
The
been
controls,
has
to
appear.
as
An
subscription
received
tuner.
continue.
number
incorrectly,
was
SiriusXM
selected
locked
or a mature
been
selected. A prompt
enter
the
Enter
described
update
by
Press
is
channel.
removed
channel
channel
by
the
unlock
the
on
to
your
has
the
any
not a valid
has
been
or
from
lineup.
has
parental
channel
code
unlock
code
page
9.
SiriusXM
been
SiriusXM
button
The
the
will
to
Sirius, XM and all related marks and logos are trademarks
of
Sirius XM Radio inc. All
rights reserved.
RADIO
Listening to the radio
To select the radio mode, press the "MODE" button and select FM/AM. Once selected the
radio frequency will be displayed. To change the frequency band, press the "BAND" button
to scroll through the band selections FM 1 > FM2 > FM3 > AM 1 > AM2
Tuning
There are three options
SEEK {Auto seek a station)
When the radio is on the desired band, the tuner will automatically select the next available
radio station as you press
MANUAL tuning
When the radio is on the desired band, pressing the
allow for manual tuning
PRESET {Storing a station)
When the radio is on the desired band and station, press and hold "PRESET" buttons 1
store the radio station.
SCAN-
While
pause for 5 seconds at each detected radio station. Pressing the "SCAN" button again will
stop the scan feature on the current station.
OPERA
Automatic Tuning Control
in
radio mode, press the "SCAN" button to scan through radio stations. The radio will
TION/AUX
of
tuning available: SEEK, MANUAL and PRESET stations
..,....,..1
or
I<~~~~<~~~~
buttons.
..,....,..1
or
1<1111<1111
for longer than 2 seconds will
of
the radio.
{9)
-6
to
P10
Page 12
RADIO OPERATION/AUX
AlPS-
To scan preset stations on the current band, short press the
for 5 seconds at each preset station.
To
seek six stations and store them on the 1-6 preset buttons.
AUX-IN Port
This port
{7)
automatically
is
available for portable
search and store radio stations, long
media
players
using a 3.5mm
press the
"AlPS" button. The radio
"AlPS" button. The tuner
(1/8")
audio jack.
will
pause
will
P11
Page 13
USB/SO OPERATION
USB
mode and play
begin
device is plugged in, the unit
When a
audio files that are stored on the device.
Use the
For fast searching, press the
"10+"
The unit can support playing music by inputting the song's sequence number directly.
This is helpful if you know the sequence number
While the unit is playing, press
on the
digits
number. Press
USB
"Preset 1"
and the
display. The four digits represent the song's sequence number. To set the four
LCD
the song you want to play, press the
of
button to
"SCAN"
"SEL"
button is for
to confirm the input and the desired song
"Play/Pause"
"SCAN"
"10-".
"AlPS"
will
audio files
"BAND"
and
on the front panel. This
"Preset 1-4"
to switch to
buttons. The
the song
of
buttons to change the sequence
USB
"SCAN"
which you want to play.
in
bring up
will
will
button is for
"SCHOOOO"
begin to play.
so
card with a card, the unit
When using a
playing audio files from the card.
mode.
Important Notice
Due to varying product specifications
functions, we cannot
SD
"SD" mode operates and functions the same as
guarantee that
will automatically turn to
regards to
in
all devices
USB/SO
be recognized and work as intended.
will
manufacturing specific
"SD" mode and begin
"USB"
Some USB/SO
devices may take more than 45 seconds to initiate after being plugged in.
P12
Page 14
CDC OPERATION
CDC
2.
3.
4.
5.
6.
7.
8.
2.
3.
4.
5.
Operation
button
Press the
1.
Connect the
display until
The LCD
Press
Press the Preset 2 ( 11) button to activate REPEAT playing
Press the Preset 3 (12) button to activate RANDOM
Follow
Pressing the
"BAND" will
Notes
1.
for
Keep discs
Do not
Do not expose discs to direct
Store discs
Fingerprints and scratches
to gently clean disc.
help clean
discs.
<!>
CDC to the
you fined CDC
will display "Disc Style", "Item Number", "Playing Time"
button to pause
"
"111-il
the function key instruction to do the operation.
"SCAN"
function as the
CD
clean and undamaged.
discs that are damaged or warped.
play
their case after use.
in
the disc. Record cleaner
On
black
button
necessary, the use of a
If
box. Once
mode.
playback
will function as the
"Previous Disc"
sunlight
affect the
will
or store
an
or
quality
plugged
button for changing discs
antistatic
in
"Next Disc"
a high temperature environment.
in
of disc
diluted natural solvent
press
playing
solvent
"MODE"
mode
mode
button and pressing
playback. Use a soft
can not
scroll through
to
the changer.
in
cloth
used to
be
can
used to clean
be
P13
Page 15
BLUETOOTH OPERATION
(BLUETOOTH DONGLE)
Model:
Installation
For optimum signal, the Bluetooth Dongle should be
should avoid metal surfaces.
weak Bluetooth signal.
RFX-BTD2
Note
for
Bluetooth
Installation
Dongle
behind or under metal surfaces
Bluetooth Mode
Press the
BTD2 mode.
"MODE" (4) button repeatedly to
scroll through available sources and select the
installed near the surface and
will
create a
To Pair with a Bluetooth device
The unit
tothe dongle.
1 .Open the Bluetooth settings
2.
3.
To
Once the device
•
Pressing the
• To change the track being played, press the
To disconnect the current Bluetooth device from the unit, simply press and hold the "AlPS"
button. This will disconnect the device but it
To erase
Play
When
on
your
a.
Press
b.
Press
c.
Press
but
d.
Press
is
ready to pair with the BT mode
on
your device.
Select "RFX4000-SX" from the list of available Bluetooth devices
Enter
Play
"0000"
music
all Bluetooth pairings stored
as the password for pairing
from a Bluetooth device
is
paired, the unit
~~
button will
start and stop the audio playback from the BT device
is
is
selected and make sure you are
ready to play music from the device.
.-.lor
will
in
the unit's memory, press and hold the
1
..
buttons
not erase the pairing from the memory.
the Bluetooth music
you
succeed
device.
the
the
and hold
this
will
and hold
previous/next
play/pause
not
in
pairing
A/PS
erase
SCAN
key
key
to
key to
the
pairing
key
to
the
Bluetooth
to
change
start
or
disconnect
from
erase
all
device,you
the
track.
pause
the
the
unit
Bluetooth
audio.
current
memory.
pairings
can
play
Bluetooth
stored
the
Bluetotth
device
in
the
in
close proximity
"SCAN" button.
music
from
the
unit,
uint
memory.
P14
Page 16
SPECIFICATION
,
..
,.,
...............
,
...... , ...........
,
TUNER(FM)
Frequency
Channel Step
Sensitivity
Stereo
Signal to Noise Radio
........................................................................ 1 OA
DC
(1
8 ohm
x 4CH
0-15.6V
allowable)
Note: Specifications and the design are subject to possible modification
without
notice due to improvement.
P15
Page 17
TROUBLESHOOTING
Unable
The unit
16/32 standard.
to
read some USB devices
is
not compatible with all USB devises. Try formatting the USB device
Cannot play certain song formats downloaded from websites
The unit does not currently support file
Takes
This
depending on file size and quantity loaded.
LCD Cannot
The audio files are not tagged properly with
language.
Power does
Check wiring and connections along with the fuse
replace. If this happens again, consult your nearest dealer.
60
seconds
is
normal operation for the unit. Some USB devices take longer than others
display
not
for
unit
to
recognize USB device.
the
MP3
song name correctly
turn on (no sound)
in
DRM (Digital Right Management) format.
103
format or they are
in
the unit. If the fuse is blown,
in
a foreign
in
FAT
No
sound
output
when operation the
unit
with
amplifiers
or
power antenna
attached
The power antenna lead could
current that
Buttons are
The connections for the front panel may be loose or dirty. Tighten connections and use a
soft cloth to clean. If this doesn't solve the problem, consult with your nearest dealer.
The
unit
Check the ground wire connection.
After
The battery voltage may be too low. Operating voltage should be between
the unit still cannot power on, consult with your nearest dealer.
unit
is
required for the amplifiers or power antenna to operate.
not
responsive
picks
up
engine noise
powers on, the
RFX-MR5BB button fail
Check if the unit has been locked. Press and hold "DISP" and "SEL" buttons to unlock.
or
unit
to
respond
be
shorted to the ground or there may be excessive
the LCD display is
immediately powers
wrong
off
11
v to 16V. If
WARRANTY INFORMATION:
Should this product require service, you may obtain specific information by contacting the
dealer from whom this product was purchased.
For any service related questions, please call
Technical Support Phone Number: 57 4-293-1521
our
technical service team.
P16
Page 18
Page 19
DIG I PORT OPERATION
Connecting
A special digi port
Users need purchase this
port at the rear
Please contact the dealers
Playing
1.
Press MODE repeatedly until the digi port mode is displayed in the LCD.
2.
Press~~
3.
Press menu to
songs
folders(PLAYLIST,ALBUM,ARTIST
play the songs. When you are selecting between the menus,
the
compatible
adaptor
of
the unit.
in
digital
MP3
digital
MP3
players
is needed to connect the compatible digital MP3 players.
adaptor
for
separately
the list
and connect this
of
compatible digital Mp3 players.
player
to pause the playing, press again to resume.
enter
menu selection ,you can press
etc.)and press
SEL
~I..,.
adaptor
to switch between
to
select
simply
key to return to up one level menu.
4. Press and
5.
Fast search(A/PS)
hold~
I..,.,
it will
fast
forward /rewind the song in playing.
to the digi
the
folder
press this
or
The marine unit can support playing the music in players by inputting the song
sequence number directly: when the
on the front panel, it will
indicates
the sequence
key 1 ,2,3,4,5 to set the five
confirm input, the unit will
6.
Playing mode switch
The
RFX4000-SX/RFX6000-SX unit will control and play the music
display
number
digits
start
"SCH 00000"
that
playing the new song automatically.
players when the digital MP3 players are connected to the
Press and Hold
current
playing mode to the
"SEL"
and
"SCAN" buttons
direct
unit
is playing songs, press
on the LCD, the five
you
want
to listen to. You can use
by pressing them repeatedly and press
A/PS
digits
preset
in
the digital
button
SEL
MP3
to
RFX4000-SX/RFX6000-SX
together
for
3 seconds to change
mode, in this mode users can control and play
the music by the digital MP3 player, press and hold the two buttons again to switch
back to the
Please Note:
default
playing mode.
RFX6000-SX
-Device for playing and charging, 2
gets 2
DIGI PORT wires DIG I PORT1 and DIG I
PORT2, but
DIGI-Devices plugged at the same time is not
only
support 1
DIG I
allowed.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.