Robot Coupe R 101 XL, R 201 XL Ultra, R 201 XL, R 211 XL Ultra, R 211 XL Operating Instructions Manual

R 101 XL

R 201 XL

R 201 XL Ultra

R 211 XL

R 211 XL Ultra

1

OPERATING INSTRUCTIONS

We reserve the right to alter at any time without notice the technical specifications of this appliance.
None of the information contained in this document is of a contractual nature. Modifications may be made at any time.
© All rights reserved for all countries by: ROBOT-COUPE s.n.c.

2

R 101 XL • R 201 XL • R 201 XL Ultra • R 211 XL • R 211 XL Ultra

Robot-Coupe

s.n.c.

- 12 avenue du Maréchal Leclerc – BP 134 – 71305 Montceau en Bourgogne Cedex - France

DECLARATION OF CONFORMITY

Declares that the machines identified by their type above,

comply with:

• the essential requirements of the following European

directives and with the corresponding national
regulations:

- Directive «Machinery» 2006/42/CE,

- Directive «Low voltage» 2006/95/CE,

- Directive «Electromagnetic compatibility»
2004/108/CE,

- Regulation «materials and articles intended to come

into contact with food»(CE) N° 1935/2004,

- Directive «plastic materials and articles intended to

come into contact with food» 2002/72/CE,

- Directive «Reduction of Hazardous Substances (RoHS)
2002/95/CE,

- Directive «WEEE» 2002/96/CE,

• the requirements of the European harmonized standards
and with the standards specifying the hygiene and
safety requirements:

- EN 12100 -1 & 2 - 2004: Safety of machinery –
General principles for design,

- EN 60204-1 -2006: Safety of machinery – Electrical
equipment of machines,

- EN 12852: Food Processors and Blenders,

- EN 1678-1998: Vegetable Cutting Machines,

- EN 454: Blender-Mixers,

- EN 12853: Hand-held Blenders and Whisks (stick
blenders),

- EN 14655: Bread Slicers,

- EN 13208: Vegetable Preparation Machines,

- EN 13621: Salad Spinners,

- EN 60529-2000: Degrees of protection,

- IP 55 55 for the electrical controls,

- IP 34 for the machines.

Signed at Montceau en Bourgogne on January 3rd, 2011

Alain NODET
The Manager

Robot-Coupe S.N.C.:

3

SUMMARY

CLEANING

• Motor base

• Cutter attachment

• Vegetable preparation attachment

• Blade

MAINTENANCE

• Blade

• Bowl locating plates

TECHNICAL SPECIFICATIONS

• Weight

• Dimensions

• Working height

• Noise level

• Electrical data

SAFETY

STANDARDS

TECHNICAL DATA (Page 11)

• Exploded views

• Electric diagram

WARRANTY

IMPORTANT WARNING

INTRODUCTION TO YOUR

NEW FOOD PROCESSOR

R 101 XL • R 201 XL • R 201 XL Ultra
R 211 XL • R 211 XL Ultra

SWITCHING ON THE MACHINE

• Advices on electrical connections

• Control panel

ASSEMBLY

• Cutter attachment

• Vegetable preparation attachment

USE & EXAMPLES

• Cutter attachment

• Vegetable preparation attachment

OPTIONS

• Serrated blade

• Slightly serrated blade

4

ROBOT-COUPE S.N.C., LIMITED WARRANTY

Your new ROBOT-COUPE appliance is
warranted to the original buyer for a
period of one year from the date of sale if
you bought it from ROBOT-COUPE s.n.c.

If you bought your ROBOT-COUPE product
from a distributor your product is covered
by your distributor’s warranty (Please check
with your distributor terms and conditions
of the warranty).

The ROBOT-COUPE s.n.c. limited warranty
is against defects in material and/or work­manship.

The ROBOT-COUPE s.n.c. warranty is given
expressly and in lieu of all other warran­ties, expressed or implied, for merchanta­bility and for fitness toward a particular
purpose and constitutes the only warranty
made by ROBOT-COUPE s.n.c. France.

8 - SHIPPING DAMAGES. Visible and latent

defects are the responsibility of the freight carrier.
The consignee must inform the carrier and consi-

gnor immediately, or upon discovery in the case

of latent defects.

KEEP ALL ORIGINAL CONTAINERS AND PAC­KING MATERIALS FOR CARRIER INSPECTION.

Neither ROBOT-COUPE s.n.c. nor its afliated
companies or any of its distributors, directors,
agents, employees, or insurers will be liable for
indirect damage, losses, or expenses linked to the
appliance or the inability to use it.

2 - Labour to sharpen and/ or replacements

for blades which have become blunt, chipped or
worn after a normal or excessive period of use.

3 - Materials or labour to replace or repair

scratch ed, stained, chipped, pitted, dented or

discoloured surfaces, blades, knives, attachments
or accessories.

4 - Any alteration, addition or repair that has not

been carried out by the company or an approved

service agency.

5 - Transportation of the appliance to or from an

approved service agency.

6 - Labour charges to install or test new attach-

ments or accessories (i.e., bowls, discs, blades, at­tachments) which have been arbitrarity replaced.

7 - The cost of changing direction-of-rotation

of three-phase electric motors (installer is res­ponsible).

THE FOLLOWING ARE NOT
COVERED BY THE ROBOT-COUPE
s.n.c. WARRANTY:

1 -

Damage caused by abuse, misuse, dropping,

or other similar damage caused by or resulting

from failure to follow assembly, operating, clea­ning, user maintenance or storage instructions.

5

UNPACKING

• Carefully remove the equipment from the packaging
and take out all the boxes or packets containing
attachments or specic items.

• WARNING - some of the tools are very sharp e.g.
blades, discs... etc.

INSTALLATION

• We recommend you install your machine on a
perfectly stable solid base.

CONNECTION

• Always check that your mains supply corresponds

to that indicated on the identification plate on the

motor unit and that it can withstand the amperage.

• The machine must be earthed.

HANDLING

• Always take care when handling the blades, as
they are extremely sharp.

ASSEMBLY PROCEDURES

• Follow the various assembly procedures carefully
(see page 6) and make sure that all the attachments
are correctly positioned.

USE

• Never try to override the locking and safety systems.

• Never insert an object into the container where the
food is being processed.

• Never push the ingredients down with your hand.

• Do not overload the appliance.

• Never switch the appliance on when it is empty.

CLEANING

• As a precaution, always unplug your appliance
before cleaning it.

• Always clean the appliance and its attachments at
the end of each cycle.

• Never immerse the motor unit in water.

• For parts made from aluminum, use cleaning uids
intended for aluminum.

• For plastic parts , do not use detergents that are
too alkaline (e.g., containing too much caustic soda
or ammonia).

• Robot-Coupe can in no way be held responsible for
the user’s failure to follow the basic rules of cleaning
and hygiene.

MAINTENANCE

• Before opening the motor housing, it is absolutely
vital to unplug the appliance.

• Check the seals and washers regularly and ensure
that the safety devices are in good working order.

• It is particularly important to maintain and check

the attachments since certain ingredients contain

corrosive agents, e.g. citric acid.

• Never operate the appliance if the power cord

or plug has been damaged or if the appliance fails
to work properly or has been damaged in any way.

• Do not hesitate to contact your local Maintenance
Service if something appears to be wrong.

IMPORTANT WARNING

WARNING: In order to limit accidents such as electric shocks or personal injury, and in order to limit material damage due to misuse of the

appliance, please read these instructions carefully and follow them strictly. Reading the operating instructions will help you get to know your
appliance and enable you to use the equipment correctly. Please read these instructions in their entirety and make sure that anyone else who
may use the appliance also reads them beforehand.

WARNING

Keep these instructions in a safe place

6

INTRODUCTION TO YOUR NEW

FOOD PROCESSOR R 101 XL •
R 201 XL • R 201 XL Ultra •
R 211 XL • R 211 XL Ultra

The R 101 XL, R 201 XL, R 201 XL Ultra, R 211 XL,
R 211 XL Ultra are perfectly geared to professional

needs. They can perform numerous tasks which you

will gradually discover as you use your machine

needs especially for Small-scale catering and
takeaway outlets.

The R 101 XL, R 201 XL, and R 201 XL Ultra consist

of a cutter bowl and vegetable preparation lid with
ejection into the bowl.

The R 211 XL, and R 211 XL Ultra consist of a cutter
and of a vegetable preparation attachments.

In cutter mode, they can be used to process

meat, vegetables, ne stufng, mousse, grinding,
kneading,… in less than 5 minutes for even the
longest tasks.

In the vegetable preparation version, the devices

have a wide range of discs for thin julienne slicing
and for the grating of vegetables.

The outstanding results coming out of your machine
will soon introduce you to a whole new world of
culinary skills and possibilities.

Thanks to their simple design both attachments can
be easily tted and removed.

This manual contains important information designed
to help the user get the most out of his/her Food
Processor.

We therefore recommend that you read the following
carefully before using your machine.

We have also included a few examples to help you
get the feel of your new machine and appreciate its
numerous advantages.

Before plugging in, check that your power supply

corresponds to that indicated on the machine’s

identication plate.
These ROBOT-COUPE machines are tted with

various types of motors:

230 V/ 50 Hz / 1
115 V/ 60 Hz / 1
220 V/ 60 Hz / 1

The machine has a single-phase plug connected to a
power machine cord.

• CONTROL PANEL

R 101 XL :

Red switch = off switch

Green switch = on switch

R 201 XL • R 201 XL Ultra
R 211 XL • R 211 XL Ultra

Red switch = off switch

Green switch = on switch

Black switch = Pulse switch

ASSEMBLY

• BOWL CUTTER ATTACHMENT

1) The motor base facing you make sure that the
bowl is straight to the motor shaft and that the safety
bar is slightly moved to your left.

We therefore recommend that you read the
following carefully before using your machine.

We have also included a few examples to help you
get the feel of your new machine and appreciate its
numerous advantages.

SWITCHING ON

THE MACHINE

2) Turn the safety bar to the right until the motor base
connectors are securely positioned in their sockets.
The safety bar should then be in front of you.

3) Place the knife on the motor shaft and lower it
right down to the bottom of the bowl.

Make sure that it is correctly positioned by making it
rotate inside the bowl.

R 101 XL - R 201 XL - R 201 XL Ultra

R 101 XL - R 201 XL - R 201 XL Ultra

R 101 XL - R 201 XL - R 201 XL Ultra

R 211 XL - R 211 XL Ultra

R 211 XL - R 211 XL Ultra

R 211 XL - R 211 XL Ultra

WARNING

THIS APPLIANCE MUST BE PLUGGED INTO

AN EARTHED SOCKET (RISK OF ELECTROCUTION).

7

4) Place the lid on the bowl and make it rotate to the
right until it clicks.

R 101 XL

R 101 XL

R 201 XL - R 201 XL Ultra

R 201 XL - R 201 XL Ultra

R 101 XL R 201 XL - R 201 XL Ultra R 211 XL - R 211 XL Ultra

R 201 XL - R 201 XL Ultra R 211 XL - R 211 XL Ultra

Once contact is made your machine is ready for use.

• VEGETABLE PREPARATION ATTACHMENT
R 101 XL , R 201 XL and R 201 XL Ultra

Follow the same procedure as for the cutter attachment
for points 1) and 2).

3) Fit the extension piece onto the motor shaft.

4) Fit the disc of your choice onto the extension

piece.

5) Place the lid on the bowl so that the large
feedhopper is facing you.

Close the lid by rotating to the right until it locks.

R 211 XL and R 211 XL Ultra:

The vegetable preparation attachment consists of two

detachable parts: the vegetable preparation bowl

and the lid.

1) The motor unit facing you, t the bowl onto
it: the ejection chute should be at the back of the

machine

2) Turn the bowl to the right until the motor unit
connectors are securely positioned in their sockets.

3) Place the plas tic discharge plate on motor shaft
and check that it is properly positioned down the
bowl.

4) Then choose the disc you want to use and place it
onto the discharge plate.

5) Place the lid on the bowl and make it rotate to the
right until the lid clicks.