Robern RF4046ARC Installation Manual

RE:flect® Mirror and RFS Shelf System - Instructions

THE RE:FLECT SYSTEM OVERVIEW: WITH THE OPTIONAL RFS SHELF, THE SURFACE MOUNTED RE:FLECT
SYSTEM CONSISTS OF FOUR ELEMENTS:

1. THE SERIES C CABINET. 2. THE RE:FLECT WALL MIRROR

3. THE RFS SHELF 4. THE SK SIDE KIT

IT IS IMPORTANT TO UNDERSTAND THAT THE RFS SHELF BRACKETS MUST BE INSTALLED DURING CABINET
INSTALLATION. SEE PAGE 2, ITEMS C & D. THE RECESSED RE:FLECT SYSTEM CANNOT USE THE RFS SHELF.

A. LAYOUT AND INSTALLATION OF THE RE:FLECT WALL MIRROR.

1. LOCATING THE CENTER OF THE ENTIRE CABINET /MIRROR COMBINATION.

EXAMPLE:
TWO MFC1628 WITH A RF2832 ARC
CENTER MIRROR IS 60" WIDE. LOCATE
THE VERTICAL CENTER LINE 30"

CENTERLINE

2. PLACE THE TWO "Z" CLIPS ON THE WALL AS SHOWN.

FROM THE LEFT OR RIGHT EDGE OR
CENTER THE LINE OVER THE FAUCET.
IN ADDITION, MARK A HORIZONTAL
LINE WITH A LEVEL AT THE DESIRED
BOTTOM POINT. WATCH FOR FAUCET
CLEARANCE WHEN USING THE RFS SHELF!

USE
#10 X 2"
SCREWS
AND

MIRROR WIDTH LESS 6"

WASHERS
WITH
ANCHORS

24"

PROVIDED

BOTTOM OF CABINET/MIRROR

3. TEST FIT THE MIRROR. ADJUST CLIPS IF NECESSARY. WITH A PENCIL, MARK THE LEFT AND RIGHT EDGES OF
THE MIRROR. REMOVE THE MIRROR WHILE INSTALLING THE CABINETS. BE CAREFUL NOT TO CHIP THE EDGES.
SECTION B DESCRIBES RECESSED MOUNTED CABINETS USED WITH THE RE:FLECT MIRROR.
SECTION C DESCRIBES SURFACE MOUNTED CABINETS USED WITH THE RE:FLECT MIRROR.
SECTION D DESCRIBES SURFACE MOUNTED CABINETS USED WITH THE RFS SHELF SYSTEM.

B. RECESSED MOUNTED CABINET LAYOUT AND INSTALLATION.

1. FOLLOW THE ROUGH OPENING GUIDE ON PAGE 3 OF THE CABINET INSTALLATION SHEET AND THE DRAWING
BELOW. BE SURE THE RE:FLECT MIRROR IS OFF THE WALL AND IN A SAFE PLACE BEFORE CUTTING OPENINGS.

•IMPORTANT• DO NOT SECURE CABINETS TO THE WALL UNTIL YOU TEST FIT THE RE:FLECT MIRROR BETWEEN THE
CABINETS. SHIMMING MAY BE NECESSARY UNDER THE RECESSED PORTION OF THE CABINET.

RF40XX
20 3/4"

RF32XX

1 3/4"

ROUGH
OPENING

16 3/4"

RF28XX
14 3/4"

RF24XX
12 3/4"

RF20XX
10 3/4"

RF16XX
8 3/4"

ROUGH
OPENING

NOTE:
FOR CUSTOM WIDTH RF MIRRORS

DIMENSION FROM CENTERLINE
TO EDGE OF ROUGH OPENING IS
1/2 MIRROR WIDTH + 3/4"

3/4"

BOTTOM OF CABINET/MIRROR

PAGE 1

MAKING SEVERAL SCORES UNTIL THE BOARD IS CUT CLEAN. INSTALL THE BOARD AS SHOWN ON PAGE 2 OF THE B/C CABINET
INSTALLATION SHEET.

2. SLIDE THE RFS BRACKET INTO THE GROOVES WHERE THE BOARD GOES. TEST FIT EACH OF THE SK SIDES AS NOTED IN
SECTION C. ABOVE. WHEN YOU ARE SATISFIED WITH THE POSITION OF MIRROR AND CABINET AND THE BRACKET IS INSTALLED
CORRECTLY AS SHOWN ON PAGE 3, COMPLETE THE INSTALLATION OF THE SK SIDES AND RE:FLECT MIRROR.

C. SURFACE MOUNTED CABINET LAYOUT AND INSTALLATION.

1.INSTALL THE MOUNTING ANGLE AS SHOWN ON PAGE 2 AND 3 OF YOUR CABINET INSTALLATION SHEET AND THE DRAWING
BELOW. TEST FIT THE SIDE MIRROR KIT TO BE SURE THE CABINET IS IN THE PROPER LOCATION.

•IMPORTANT• DO NOT INSTALL THE SK SIDES UNTIL YOU ARE SURE THE RE:FLECT MIRROR FITS BETWEEN THEM.

•IMPORTANT• INSTALL THE RFS SHELF CLIPS UNDER THE CABINETS BEFORE THE SK SIDES ARE INSTALLED. THE BOTTOM
BOARD OF THE CABINET MUST BE CUT. SEE D. BELOW.

RF40XX
21 1/2"

RF32XX
17 1/2"

RF28XX
15 1/2"

RF24XX
13 1/2"

NOTE:
FOR CUSTOM WIDTH RF
MIRRORS

DIMENSION FROM CENTERLINE
TO EDGE OF MOUNTING ANGLE
IS
1/2 MIRROR WIDTH + 1 1/2"

RF20XX
11 1/2"

RF20XX
11 1/2"

CABINET
MOUNTING
ANGLE

1 1/2"

D. INSTALLING THE RFS RE:FLECT SHELF SYSTEM.

1. BEFORE INSTALLING THE CABINETS THE BOTTOM BOARD MUST HAVE 3/4" CUT FROM ONE END. USE A UTILITY KNIFE

PAGE 2