Robern PLSK30 Installation Manual
PLM CABINET AND MTL LIGHT INSTRUCTIONS
General Notes
Robern
701 N. Wilson Ave.
Bristol, PA 19007
800.877.2376
1. Unpack the cabinet. Check the box thoroughly
for all hardware and loose parts as follows:
1. Cabinet 2. Hardware Bag 3. Shelving
4. Mounting Bar
(Do not throw any parts away until install is complete.)
2. Remove the doors from the cabinet. (See gure E,
Hinge Screw 3) and store the doors in the cabinet
box. Be sure edges of doors are protected.
3. A square and plumb installation insures proper door
operation. A square and level are necessary for
proper installation.
4. Improper installation voids the warranty. Installed
cabinets cannot be returned.
5. If you experience any problems with your cabinet
contact your dealer or Robern directly.
Robern • 701 N Wilson Ave • Bristol, PA 19007
800 877 2376 • FAX 215 826 9633
Limited Warranty One Year Term
ROBERN warrants to the original purchaser that, it will, at its election repair, replace, or make appropriate adjustment to products
made by this company shown to have signicant defects in material or workmanship which are reported to ROBERN in writing
within one (1) year from the date of delivery. ROBERN is not
responsible for installation costs.
The warranty is void in the event the product is damaged in transit,
or if damage or failure is caused by abuse, misuse, abnormal
usage, faulty installation, damage in an accident, improper maintenance, or any repairs other than those authorized by ROBERN.
At the expiration of the one year warranty period, ROBERN shall
be under no further obligation under any warranty, expressed or
implied, including the implied warranty of merchantability.
Part List
1. PLM Cabinet
(See sufx codes
on following page
for model options.)
2. Glass Shelves
– 3 Shelves are provided
with each cabinet
3. Mounting Bar
– Bar used for surface
mounted cabinets.
4. Hardware Bag • Contains the Following
A. 5 Plastic Anchors
B. 36 Shelf Hole Plugs
C. 6 SMS/WOOD Screws #10 x 2”
D. 10 Connector Block Screws #10 x 1/2”
E. 2 MP65 Connector Blocks
F. 10 Black or White Screw Head Caps
G. 3 Small Top Mount “Z’ Clip
H. 12 Clear Snap-In Shelf Clips
ROBERN shall not be liable for any consequential damages arising out of or in connection with the use or performance of its
products. Some states do not allow limitations on how long an
implied warranty lasts or do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Any liability against ROBERN under any implied warranty, including the warranty of merchantability, is expressly limited to the
terms of this warranty. Permission to return any merchandise
under this warranty must be authorized by ROBERN and returned
prepaid by the purchaser. Claims under this warranty should be
sent directly to your dealer.
©2003 PL Bath
All rights reserved.
REV. 8 03/25/2003
1
SS489 PLM BATH CABINET & MTL LIGHT INSTRUCTIONS
PLM Model Number Destinations
Product Product Product
Model Type Description
PLM Cabinet Rotate for Left/
See page 8 Right hand opening
PLSK30 Side Kit For Surface
Mounting
MTL16F / 20F/ 24F Light Fluorescent 18 - 27
Fixture Width
MTL16, 20, 24,, 30, 36 T Light Incandescent 3, 5, 6
Fixture or 7 Bulb
*MTL33T Light Vertical 6 Bulb
Fixture Fixture (2)
**MTL1.5F Light Vertical Fluorescent
Fixture Fixture
PLM1630, PLM2030, PLSK30 Side Kit MTL16F, 20F, 24F,
or PLM2430 Cabinet 16T & 24T Light
` Fixtures
4 5/8” Deep Overall Purchased separately Purchased separately
width & height below for surface mounted for built in light.
cabinets
When recessed into Extra mirrors for Can be recessed or
a wall. MTL16F Light surface mounted.
A. 3 3/4” in wall Fixture Attaches to cabinet.
(4” deep)
B. 7/8 projects out
from wall.
Dimensions of Cabinets
1. PLM is a modular system allowing you to install cabinets
in multiples. Each cabinet is supplied with
interconnecting hardware used to gange the surface.
Two types of MTL light xtures, an incandescent or
uorescent source, are an option which can be added to
the top of the cabinets, lights add 3” to the height of
the cabinet.
Overall size is determined by the overall dimensions
of the assembled units. Rough openings for recessed
installations are shown at the right.
Different width cabinets (and lights) can be combined as
shown on the right.
2. Examples are shown below:
Single
Cabinet
Two Door
Cabinet &
Light
Combination
Three Door
Cabinet
Combination
Four Door Cabinet &
Light Combination
One Door Cabinets Without Lights
Model Number Overall Wall Opening
No. of Units W x H W x H
PLM1630 1 15 1/4” X 30” 14 1/2” X 29 1/4”
2 30 1/2” X 30” 29 3/4” X 29 1/4”
3 45 3/4” X 30” 45” X 29 1/4”
4 61” X 30” 60 1/4” X 29 1/4”
PLM2030 1 19 1/4” X 30” 18 1/2” X 29 1/4”
2 38 1/2” X 30” 37 3/4” X 29 1/4”
3 57 3/4” X 30” 57” X 29 1/4”
4 77” X 30” 76 1/4” X 29 1/4”
PLM2430 1 23 1/4” X 30” 22 1/2” X 29 1/4”
2 46 1/2” X 30” 45 3/4” X 29 1/4”
3 69 3/4” X 30” 69” X 29 1/4”
4 93” X 30” 92 1/4” X 29 1/4”
16 & 24 2-16 / 1-24 53 3/4” X 30” 53” X 29 1/4”
Combined 2-24 / 1-16 61 3/4” X 30” 61” X 29 1/4”
2-24 / 2-16 77” X 30” 76 1/4” X 29 1/4”
One Door Cabinets With Lights
Model Number Overall Wall Opening
No. of Units W x H W x H
PLM1630 1 15 1/4” X 30” 14 1/2” X 321/4”
with 2 30 1/2” X 30” 32 3/4” X 32 1/4”
MTL16F or 3 45 3/4” X 30” 45” X 32 1/4”
MTL16T 4 61” X 30” 60 1/4” X 32 1/4”
PLM2030 1 19 1/4” X 30” 18 1/2” X 32 1/4”
with 2 38 1/2” X 30” 37 3/4” X 32 1/4”
MTL16F or 3 57 3/4” X 30” 57” X 32 1/4”
MTL16T 4 77” X 30” 76 1/4” X 32 1/4”
* MTL33T:
This xture adds 6” to the width
of an installation per light kit.
Refer to the instructions with
the light for details.
* MTFLBLN:
This xture adds 3” to the width
of an installation per light kit.
Refer to the instructions with
the light for details.
SS489 PLM BATH CABINET & MTL LIGHT INSTRUCTIONS
PLM2430 1 23 1/4” X 30” 22 1/2” X 32 1/4”
with 2 46 1/2” X 30” 45 3/4” X 32 1/4”
MTL16F or 3 69 3/4” X 30” 69” X 32 1/4”
MTL16T 4 93” X 30” 92 1/4” X 32 1/4”
16 & 24 2-16 / 1-24 53 3/4” X 30” 53” X 32 1/4”
combined 2-24 / 1-16 61 3/4” X 30” 61” X 32 1/4”
with MTL 2-24 / 2-16 77” X 30” 76 1/4” X 32 1/4”
2
THREE CABINET COMBINATION FOR RECESS INSTALLATION
CABINET
MP65 CONNECTOR
CABINET
CABINET
MP65 CONNECTOR
USE PLSK30
SIDE KIT FOR
SURFACE MOUNT.
REFER TP PAGE 5,
FIGURE I.
CABINET CABINET CABINET
#10 X 1/2"
SCREWS
MP CONNECTORS
C
L
C
L
PLL LIGHT FIXTURE
(PLL-F SHOWN)
PLM16 CABINET
LIGHT ATTACHMENT
TO CABINET
WIRING
LOCATION
Assembly of PLM Cabinets
1. Each cabinet contains two MP65 connectors
to allow combinations of cabinets, both surface
mounted using the PLSK side kit as well
as recessed into the wall. A plan view noting
these connector combinations are shown in
the example below in gure A.
Assembly of PLM Cabinets and
MTL- T/F Top Lights
2. If you are using MTL- T/F top light xtures refer now to the
instructions provided with the xture. The light xture is
attached to each cabinet before the cabinets are ganged
together and/or installed in or on the wall.
Refer to the side view shown in gure B. The side plates on
the light xture are attached to the cabinet using screws
holding the cabinet frame together. Refer to the instructions
supplied with the light for complete detail.
Assembly of PLM Cabinets and
MTL- T/F Side Lights
3 If you are using MTL- T/F side light xtures refer now to
the instructions provided with the xture. These light
xtures are supplied with special connectors to allow
installation between or at the ends of the cabinet array
as seen in gure B.
4. With the doors off, combine the boxes with
the MP65 connectors to assemble per your
layout. Use the #10 x 1/2” thread cut screws.
Assemble on a convenient at surface, not
on or in wall.
Do not attach doors or side kits until boxes
are secured in wall.
Note location of holes in the cabinets which
are used to secure connectors and side kits
as seen in gure E on page 3.
Fig. B1
Fig. C
3
SS489 PLM BATH CABINET & MTL LIGHT INSTRUCTIONS
Loading...