Page 1
User's Guide
TCO HDSP / FF
Time Code Option
for HDSP PCI / Fireface 800
LTC / SMPTE Reader and Generator
Video to Word Clock Converter
Low Jitter Word Clock Regeneration
Page 2
Bedienungsanleitung TCO
2
Contents
1 Introduction...............................................................3
2 Package Contents.....................................................3
3 Hardware Requirements ..........................................3
4 Technical Specifications
4.1 TCO-FF..................................................................4
4.2 TCO-HDSP............................................................4
5 Installing the TCO-HDSP..........................................5
6 Installing the TCO-FF................................................5
7 Operation and Usage
7.1 TCO-FF..................................................................7
7.2 TCO-HDSP............................................................8
7.3 Status Displays......................................................9
8 Warranty...................................................................10
9 Appendix..................................................................10
Page 3
Bedienungsanleitung TCO
3
1. Introduction
Thank you for choosing the TCO. The Time Code Option provides synchronisation to SMPTE
and video in professional studio quality. SteadyClock ensures that the word clock derived from
the input signals is of low jitter and therefore highly compatible. The TCO supports all standard
formats and conversions of these, turning it into a highly useful tool within the studio environment.
2. Package Contents
Please check your TCO component's package to include each of the following:
TCO-FF
• TCO board with fixed ribbon cable
• 1 set of screws
• User's guide
TCO-HDSP
• TCO
• 1 ribbon cable
• User's guide
3. Hardware Requirements
The TCOs can be operated with the following hardware:
TCO-FF:
Fireface 800
TCO-HDSP:
HDSP AES-32
The HDSP 9632 will be supported later too.
Current state:
Under Windows XP the TCO-HDSP provides the SMPTE position as APP (ASIO Positioning
Protocol) and as MTC Sync. Under Mac OS X the TCO-HDSP provides the SMPTE position as
MTC Sync.
Under Windows XP the FF-HDSP provides the SMPTE position as APP (ASIO Positioning Protocol) and as MTC Sync. Under Mac OS X the TCO-FF provides the SMPTE position as MTC
Sync.
Upcoming features:
Compatibility to HDSP 9632
LTC Output
Page 4
Bedienungsanleitung TCO
4
4. Technical Specifications
4.1 TCO-FF
LTC/Video In
• LTC In: BNC, unbalanced
• Level range LTC In: -25 dBu up to +12 dBu
• Video In: BNC unbalanced, switchable termination 75 Ohm
• Format: PAL and NTSC
LTC Out
• BNC
• Output level: +4 dBu, via jumper –7 dBu
• Output impedance: 220 Ohm
• Power supply via ribbon cable, 5 V DC, 100 mA
• Dimensions (WxD): 100 x 75 mm
4.2 TCO-HDSP
LTC In
• BNC, unbalanced
• Level range: -25 dBu up to +12 dBu
Video In (Word Clock In)
• BNC, switchable termination 75 Ohm
• Format: PAL and NTSC
Word Clock In (Video In)
• BNC, switchable termination 75 Ohm
• Transformer coupled, galvanically isolated input
• Not affected by DC-offsets within the network
• Signal Adaptation Circuit: signal refresh through auto-center and hysteresis
• Overvoltage protection
• Level range: 1.0 Vpp – 5.6 Vpp
• Lock Range: 28 kHz – 200 kHz
• Jitter when synced to input signal: < 1 ns
• Jitter suppression: > 30 dB (2.4 kHz)
LTC Out
• BNC
• Output level: +4 dBu, via jumper –7 dBu
• Output impedance: 220 Ohm
Word Clock Out
• BNC
• Max. output voltage: 5 Vpp
• Output voltage @ 75 Ohm termination: 4.0 Vpp
• Output impedance: 10 Ohm
• Frequency range: 28 kHz – 52 kHz
• Power supply via ribbon cable, 5 V DC, 100 mA
• Standard bracket, dimensions PCB (WxD): 98 x 75 mm
Page 5
Bedienungsanleitung TCO
5
5. Installing the TCO-HDSP
Before installing the TCO card, please make sure the computer is switched off and the
power cable is disconnected from the mains supply.
1. Disconnect the power cord and all other cables from the computer.
2. Remove the computer's housing. Further information on how to do this can be obtained
from your computer´s instruction manual.
3. Before removing the TCO from its protective bag, discharge any static in your body by
touching the metal chassis of the PC.
4. Connect the TCO with the PCI card using the supplied flat ribbon cable. For this, plug one
end of the cable into the matching connector of the PCI card. On the AES-32 the connector
is labeled Synchronizer Board, on the 9632 the TCO replaces the Wordclock Module.
Plug the other end into the connector X101 on the TCO.
5. Insert the TCO into a free PCI slot and fasten the screw. The TCO needs no slot on the
motherboard, but includes a stabilizing edge, which fits in both PCI and ISA slots.
6. Insert the PCI card firmly into a free PCI slot, press and fasten the screw.
7. Replace the computer's housing.
8. Reconnect all cables including the power cord.
6. Installing the TCO-FF
To install the TCO the Fireface 800 must be opened. If you feel unsecure to do so please consult a technician and let him show you how to do it. Else please follow the instructions below
step by step.
Before installing the TCO, please make sure the Fireface 800 is switched off and the power
cable is disconnected from the mains supply.
1. Disconnect the power cord and all other cables from the Fireface 800.
2. Loosen and remove both rack ears (two screws each).
3. Use a screwdriver (Phillips 1) to remove the 3 screws on the cover near the back panel, and
2 screws on each side of the Fireface 800, so that the cover can be taken off by sliding it to the
rear.
4. Remove the TCO spare plate within the rear panel (2 screws).
5. Before removing the TCO from its protective bag, discharge any static in your body by touch-
ing the metal chassis of the Fireface.
6. Slide the TCO into the rear panel's hole from the inside. Watch the correct position, so that
both screws found in the PCB of the TCO do not press on the TRS jacks, but are placed inbetween those.
7. Fasten the TCO with the two black self-tapping screws from the TCO screw set. Do not use
the screws of the spare plate, as these are thread screws.
Page 6
Bedienungsanleitung TCO
6
8. Fold the ribbon cable one time and plug it into socket X1105 on the motherboard, see picture
below.
Now you are ready to re-assemble the Fireface.
9. Check that the safety-earth wire (yellow–green) is still connected to the cover. Then put the
cover on and slide it into the aluminum front panel of the Fireface 800.
10. Fasten the 3 screws on the cover and the two screws on each side of the Fireface 800.
11. Attach and fasten the rack ears. Finished!
Page 7
Bedienungsanleitung TCO
7
7. Operation and Usage
7.1 TCO-FF
After installation of the TCO the Fireface 800 has to be updated to the latest driver and firmware
version. The current files are found on the website www.rme-audio.com
in the section Downlo-
ad. At the time of printing these are:
http://www.rme-audio.com/download/fut_win_fire_tco.zip
Firmware updater version 2.63 for Windows 2000/XP/Vista
http://www.rme-audio.com/download/w2fire_265.zip
Driver version 2.65 for Windows 2000/XP
http://www.rme-audio.com/download/fut_mac_fire_tco.gz
Firmware updater version 2.64 for Mac OS X
http://www.rme-audio.com/download/macfire_258.gz
Driver version 2.58 for Mac OS X
http://www.rme-audio.com/download/fireface_x86.gz
Driver version 2.58 for Intel Macs
The settings dialog now includes an additional page TCO, and on the main page the new sync-
option TCO can be selected.
For synchronization to a video or LTC signal choose Clock Mode AutoSync and TCO as Pre-
ferred Sync Ref on the main page of the settings dialog. All further settings are done on the
TCO page.
Sync Source: Input select switch for the
inputs LTC and video. Lock is dispayed as
soon as the TCO is able to synchronize on an
input signal.
Video Input: The BNC input can be
terminated with 75 Ohms.
Frame Rate: The frame rate of the incoming
SMPTE signal must always be defined
manually.
Sample Rate: The TCO derives a word clock
of 44.1 kHz or 48 kHz from the sync-signal. In
the setting 'from App' the value sent from the
ASIO application to the driver is used. The
lower field provides common Pull-Up and PullDown values. The final value of the previously
defined sample rate is shown in the field
Frequency in case the sync-signal is valid.
Frequency: The TCO measures the word
clock that it generates and shows the current
value in this field.
MIDI Input: The Fireface's MIDI input
includes either the MTC signal of the TCO, or
the MIDI data of the 5-pin DIN input (External).
Page 8
Bedienungsanleitung TCO
8
7.2 TCO-HDSP
After installation of the TCO-HDSP the HDSP AES-32 has to be updated to the latest driver and
firmware version. The current files are found on the website www.rme-audio.com
in the section
Download. At the time of printing these are:
http://www.rme-audio.com/download/fut_win_dsp_b10.zip
Firmware updater version 233 for AES-32 under Windows 2000/XP/Vista
http://www.rme-audio.com/download/hdsp_wdm_302.zip
WDM streaming driver version 3.02 for HDSP series under Windows 2000/XP/Vista
http://www.rme-audio.com/download/fut_mac_madi.gz
Firmware updater version 233 for AES-32 under Mac OS X
http://www.rme-audio.com/download/madi_aes_253.gz
Driver version 2.53 for AES-32 under Mac OS X
The settings dialog now includes an additional page TCO, and on the main page the new sync-
option TCO can be selected.
For synchronization to a video or LTC signal choose Clock Mode AutoSync and TCO as Pre-
ferred Sync Ref on the main page of the settings dialog. All further settings are done on the
TCO page.
Sync Source: Input select switch for the
inputs LTC, video and word clock. Lock is
dispayed as soon as the TCO is able to
synchronize on an input signal. Also at the
bracket the green LED will light up.
Video / Word Input: The BNC input can be
terminated with 75 Ohms. At the bracket the
yellow LED will light up.
WCK Conversion: Default setting is 1:1.
This very special option allows for a
synchronous conversion of the word clock
input signal. 44.1 kHz will turn into 48 kHz,
where the 48 kHz are not free running, but
have a synchronous relationship to the
original clock. The same is available for
converting 48 kHz to 44.1 kHz.
Frame Rate: The frame rate of the incoming
SMPTE signal must always be defined
manually.
Sample Rate: The TCO derives a word clock
of 44.1 kHz or 48 kHz from the sync-signal.
With the setting 'from App' the value sent
from the ASIO application to the driver is
used.
The lower field provides common Pull-Up and Pull-Down values. The final value of the previously defined sample rate is shown in the field Frequency in case the sync-signal is valid.
Frequency: The TCO measures the word clock that it generates and shows the current value in
this field.
Page 9
Bedienungsanleitung TCO
9
Note: The MTC signal is provided via a new (virtual) MIDI input port. This one has to be chosen
as MTC sync source in the application.
7.3 Status Displays
The page TCO includes useful status displays, providing detailed information about the incoming signal.
LTC In: The time values read from the LTC signal. These values are passed unchanged to the
application.
Input State: An LTC input signal detection as valid (valid) is followed by the display of the number of frames per second, and wether this is Full Frame or Drop Frame code. A valid video signal is shown as PAL or NTSC. An incoming word clock signal is analyzed and displayed to be in
the Single Speed, Double Speed or Quad Speed range.
Page 10
Bedienungsanleitung TCO
10
8. Warranty
Each individual TCO undergoes comprehensive quality control and a complete test at IMM before shipping. The usage of high grade components allow us to offer a full two year warranty.
We accept a copy of the sales receipt as valid warranty legitimation.
If you suspect that your product is faulty, please contact your local retailer. The warranty does
not cover damage caused by improper installation or maltreatment - replacement or repair in
such cases can only be carried out at the owner’s expense.
Synthax Audio AG does not accept claims for damages of any kind, especially consequential
damage. Liability is limited to the value of the TCO. The general terms of business drawn up by
Synthax Audio AG apply at all times.
9. Appendix
RME news, driver updates and further product information are available on our website:
http://www.rme-audio.com
Manufacturer:
IMM Elektronik GmbH, Leipziger Strasse 32, D-09648 Mittweida
Trademarks
All trademarks, registered or otherwise, are the property of their respective owners. RME, Ham-
merfall, SyncAlign und SyncCheck sind eingetragene Marken von RME Intelligent Audio Solutions. Fireface 800, TCO und SteadyClock sind Warenzeichen von RME Intelligent Audio
Solutions. Microsoft, Windows, Windows 2000 und Windows XP sind registrierte oder Warenzeichen der Microsoft Corp. Apple und Mac OS sind eingetragene Marken der Apple Computer
Inc. ASIO ist ein Warenzeichen der Steinberg Media Technologies GmbH.
Copyright © Matthias Carstens, 3/2007. Version 1.2
Although the contents of this User’s Guide have been thoroughly checked for errors, RME can not guarantee that it is
correct throughout. RME does not accept responsibility for any misleading or incorrect information within this guide.
Lending or copying any part of the guide or the RME Driver CD, or any commercial exploitation of these media without
express written permission from RME Intelligent Audio Solutions is prohibited. RME reserves the right to change specifications at any time without notice.
Page 11
Bedienungsanleitung TCO
11
CE / FCC Compliance
CE
This device has been tested and found to comply with the limits of the European Council Directive on the approximation of the laws of the member states relating to electromagnetic compatibility according to RL89/336/EWG and RL73/23/EWG.
FCC Compliance Statement
Certified to comply with the limits for a Class B computing device according to subpart J or part
15 of FCC rules. See instructions if interference to radio reception is suspected.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause
undesired operation.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the seperation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help.
In order for an installation of this product to maintain compliance with the limits for a Class B
device, shielded cables must be used for the connection of any devices external to this product.
Note on Disposal
According to the guide line RL2002/96/EG (WEEE – Directive on Waste
Electrical and Electronic Equipment), valid for all european countries, this
product has to be recycled at the end of its lifetime.
In case a disposal of electronic waste is not possible, the recycling can
also be done by IMM Elektronik GmbH, the manufacturer of the Micstasy.
For this the device has to be sent free to the door to:
IMM Elektronik GmbH
Leipziger Straße 32
D-09648 Mittweida
Germany
Shipments not prepaid will be rejected and returned on the original sender's costs.
Page 12
Bedienungsanleitung TCO
12
Loading...