IF YOU HAVE ANY QUESTIONS OR CONCERNS, OR ARE MISSING PARTS
DO NOT RETURN SPRAYER TO THE STORE!
PLEASE CALL OUR CONSUMER HOTLINE AT 1-800-253-4642 Year Round: Mon. – Fri., 8:00 a.m. to 7:00 p.m., ET
March 1 – August 31: Sat. and Sun., 10:00 a.m. to 4:00 p.m., ET Or write us at: Root-Lowell Manufacturing Co., 1000 Foreman Rd. P.O. Box 289, Lowell, MI 49331
Visit us on the internet: www.rlflomaster.com e-mail: service@rlflomaster.com
Owners’ Manual
Lawn & Garden Polymer
Funnel Top Sprayers
WARNING!!! THIS PRODUCT IS DESIGNED TO SPRAY CHEMICALS THAT MAY BE HARMFUL AND COULD CAUSE SERIOUS PERSONAL INJURY IF INHALED OR BROUGHT INTO CONTACT WITH THE USER. FAILURE TO READ AND FOLLOW OWNERS’ MANUAL INSTRUCTIONS BEFORE USE AND/OR MISUSE OF THIS PRODUCT COULD RESULT IN EXPLOSIVE FAILURE
WITH MAJOR INJURIES.
•ALWAYS water test sprayer before each use.
•ALWAYS wear long sleeve shirts, long pants, goggles, gloves and durable shoes.
•ALWAYS READ AND FOLLOW label instructions for the chemicals to be applied.
•AFTER USE release pressure and clean the sprayer.
•ALWAYS RELEASE pressure in sprayer before servicing.
•DO NOT alter the sprayer or any components.
•DO NOT spray flammable, caustic (i.e. acids, chlorines and bleach), corrosive, heated or self-heating solutions with this sprayer.
•DO NOT store liquids in the sprayer.
•NEVER fill tank above the “MAX FILL LINE” on the tank.
ASSEMBLY INSTRUCTIONS
A. HOSE TO TANK ASSEMBLY
1.Insert the pink siphon tube approximately ½” into the pink hose insert otherwise sprayer will spray only air.
2.Lubricate the black o-ring on the pink hose insert and then push (2a) into the threaded tank nipple until fully seated.
3. Screw hose nut onto threaded tank nipple. Firmly hand tighten.
1 |
2 |
2a |
3 |
B. FLOW CONTROL TO HOSE
1.Remove the flow control hose nut from the flow control and slide over the hose.
2.Push the hose over the pointed end of the flow control until it touches the threads.
3.Screw the flow control hose nut onto the flow control. Firmly hand tighten.
1 |
2 |
3 |
C. WAND TO FLOW CONTROL
1.Push the wand into the flow control until it stops.
2.Slide the o-ring down until it touches the flow control.
3.Screw the wand nut onto the flow control. Firmly hand tighten.
1 |
2 |
3 |
TO ENSURE CORRECT ASSEMBLY, TEST SPRAYER WITH
WATER BEFORE USING.
OPERATING INSTRUCTIONS
A. FILLING THE SPRAYER
1.Remove the pump assembly from the tank by turning counter-clockwise.
2.Prepare the spray solution following the instructions listed on the chemical manufacturers’ label. Mix only the amount of solution to be sprayed.
3.DO NOT spray flammable, caustic (i.e. acids, chlorines and bleach), corrosive, heated or self-heating solutions with this sprayer.
4.Screw the pump assembly back into the tank by turning clockwise. Firmly hand tighten.
5.NEVER fill tank above the “MAX FILL LINE” on the tank.
B. PRESSURIZING THE SPRAYER
1.To operate the pump, unlock the pump handle by turning counter-clockwise. Be careful not to loosen the pump from the tank.
2.To create pressure, stroke up and down.
3.Lock the pump handle back into the pump assembly by turning clockwise.
WARNING!!! To prevent ejected pump assembly and/or solution from striking and injuring you, never stand with your face or body directly over the top of the tanks when pumping or loosening the pump.
C. SPRAYING
1.To start spraying, squeeze the flow control lever.
2.To stop spraying, release the flow control lever while pulling back on the lever.
3.To spray continuously, squeeze the flow control lever and slide forward to lock on.
4.If your sprayer has an adjustable cone nozzle, screw it clockwise for a fine mist and counter-clockwise for a coarse stream. Flat fan nozzles are not adjustable.
5.DO NOT remove flow control cap while spraying.
6.ALWAYS wear long sleeve shirts, long pants, goggles, gloves and durable shoes.
2 |
3 |
5 |
D. RELEASING PRESSURE
1.To release pressure from the tank, turn the tank upside down, and then squeeze the flow control lever until all the air pressure is gone. If your sprayer has a pressure relief valve, turn yellow knob clockwise until all air pressure is gone.
2.If your sprayer is clogged and the pressure will not release using the flow control, do the following:
a.Place a rag over the top of the sprayer and pump.
b.While firmly pushing down on the pump handle, slowly turn counter-clockwise.
3.ALWAYS RELEASE pressure in sprayer before servicing.
4.NEVER leave pressurized sprayer unattended.
Loading...