Rinnai APPLICATION PROJECT FORM Miscellaneous Information

APPLICATION PROJECT FORM

Please send completed form to engineering@rinnai.us or fax to 678-829-1666

CUSTOMER INFORMATION

Customer Name: Date:

Rep/Dealer/Installer Name:

Company:

Phone: Email:

Job Name:

Address:

City: State: Zip:

APPLICATION INFORMATION SIZING CONSTRAINTS

Application Type Set Temp. °F

Fuel Type NG Ground Temp. °F

LP Temperature Rise °F

Equipment Arrangement Tankless Options Only Elevation ft

Tankless with Storage

Installation Type Non-condensing Tankless

Condensing Tankless Water Heaters

Equipment Location Indoor

Outdoor

Note:

1) Please list as applicable any diversity requirements for speciﬁc hot water ﬁxtures

2) If you have a split system please note how the system is separated by using the Fixture ID#’s

3) Also note if there are to be dierent temperatures in each system

4) Restaurant: All commercial kitchens will be sized using a 100˚F temperature rise unless instructed otherwise. Ensure make and model of commercial dishwasher is listed below. Provide ﬁxture type and quantity of all hot water ﬁxtures

5) If hotel, apartment/condo, nursing/retirement home or the like, ﬁll out hot water ﬁxture list and room quantities in appropriate tables

6) Laundry: enter quantity and capacity of each washer

HOT WATER FIXTURE LIST (enter as applicable)

ID QT Y. TYPE ID Q T Y. TYPE

1 14

2 15

3 16

4 17

5 18

6 19

7 20

8 21

9 22

10 23

11 24

12 25

13 26

NOTES

APPLICATION PROJECT FORM

Please send completed form to engineering@rinnai.us or fax to 678-829-1666

HOTELS, APARTMENTS/CONDOS/NURSING/ RETIREMENT HOMES

ROOM TYPE QUANTITY

1 Bedroom

2 Bedroom

3 Bedroom

LAUNDRY (list washer quantity, pound capacity and operational diversity)

WASHER QTY POUND CAPACITY (LB) % DIVERSITY 1

Complete below if a Rinnai Tankless Rack System and/or Common Vent will be used.

RACK SELECTION

Wall Mount

Rack Option

Free Standing (back-to-back) Free Standing (in-line)

NOTES

Enter information below for exhaust components only.

VENT SELECTION

Select Vent Option

How will vent terminate?

What is the elevation (ft)?

What is the roof pitch?

What is the total vent run (ft)?

(exclude 90° and 45° elbows)

How many 90° elbows/vent run?

How many 45° elbows/vent run?

Will vent pass through interior

Interested in Bug Guard?

Note: Common Vent System is for use only with Rinnai tankless condensing water heater RU98i(REU-KB3237FFUD-US)

Disclaimer:

The Application Engineers at RAC are relying on the information provided above to try to assist you in determining the model type and number of products needed to meet your particular application. This sizing analysis is intended to be used as a guide only and not as a replacement for a professionally engineered project. The Application Engineers have not been to the location so this guidance is for your assistance only and should not be the sole factor in making your decision. Sizing does not describe a complete system. The contractor/ engineer must determine the necessary components for and conﬁguration of the particular system being installed. Sizing does not imply compliance with local building codes. It is the engineer/contractor responsibility to ensure the installation is in accordance with all local building codes. Confer with local building ocials before installation When using a Rinnai product as the heat source for a circulation loop, the piping systems should be designed with a hot water circulation loop having a minimum circulating ﬂow rate of 3 gpm. You must also review pressure drop curves for the Rinnai when sizing circulators. The Circulation Pump must be controlled by an aqua stat, timer or both Rinnai Water Heaters cannot be used in applications requiring 180-195°F water at a DISHWASHER, unless a booster heater capable of producing 180-195°F water is provided at the dishwasher. The Rinnai Water Heater is not to be used as a booster water heater in these applications For applications using a commercial dishwasher, a hot water circulating loop feeding the dishwasher must be installed. For Beauty Salon applications, a hot water circulation loop feeding the head wash stations is highly recommended. This provides instant hot water to head wash stations and reduces the occurrence of cold burst. (Refer to Hot Water System Design Manual for piping schematics). Insulation of recirculation piping is also recommended for heat retention. Air surrounding the water heater, venting, and vent termination(s) is used for combustion and must be free of any compounds that cause corrosion of internal components. Please refer to Rinnai Operation and Installation manual for further information. Remember that gases from beauty salons and fume hoods of commercial dish washers with chemical sanitizers can be highly corrosive and may cause premature failure of water heater components. Care must be taken to ensure tankless and vent termination are installed away from that area. An uncontaminated supply of combustible air must be maintained for optimum performance of the water heater If the intended installation is located in hard water area, a softener or similar water treatment system must be used. Always remember to perform routine maintenance. Rinnai America Corporation, its agents, employees, directors, ocers, parent or aliate companies assume no liability for damages arising from information provided herein to or by consumers or third parties or for damages arising from or associated with water quality, compliance with local codes, installation methods, materials or other circumstances related to application or installation.

Rinnai America Corporation • 103 International Drive Peachtree City, GA 30269 • 800-621-9419

ﬁre wall?

Common Vent (back-to-back)

Common Vent (in-line)

Standard Concentric

Roof

Wall

Yes