Page 1
This manual is used to help users to quickly get
Quick Guide
.
Selection Guide
DP800 Series Programmable
Linear DC Power Supply
familiar with the main features and key
specifications of each model of DP800 series so as
to select the desired model and options according
to the actual need.
For the detailed specifications, please refer to
DP800 Data Sheet
please refer to
; for an overview of the products,
DP800A Quick Guide
and
DP800
RIGOL TECHNOLOGIES CO., LTD.
Page 2
DP800 Series Overview
DP800 series is high-performance programmable linear DC power supply. It is designed with clear user interface,
superb performance specifications, various analysis functions and various communication interfaces. DP800
series can fulfill versatile test requirements.
Main Features
Three-channel/dual-channel/single-channel models available, up to 200W total output power
Low ripples and noise:
DP832A/DP832/DP831A/DP831/DP822A/DP822/DP821A/DP821: <350uVrms/2mVpp
DP813A/DP813/DP811A/DP811: <350uVrms/3mVpp
Excellent load regulation rate and linear regulation rate
Fast transient response time: <50μs
Some channels are isolated
Provide overvoltage/overcurrent/overtemperature protection function
Independent control for each channel
Support serial and parallel output functions
Some channels support the track function to track the channel voltage setting value and output on/off
status
Provide the Sense function to automatically compensate for the voltage drop caused by the load lead in
high current output
Provide timing output and delay output functions
Provide built-in recorder to sample and record the channel output according to the specified record period
Provide analyzer to analyze the recorded files and provide the analysis results of the channel voltage,
current and power
Support monitor to monitor the output status of the instrument and the instrument will execute the
corresponding operation according to the current setting when the specified monitor condition is met
Provide trigger and support trigger input and trigger output
Built-in V,A,W measurements and waveform display
3.5-inch TFT display
Various interfaces: USB Host&Device, LAN, RS232, USB-GPIB (option), digital IO, rear panel output
interface (for DP813A/DP813/DP811A/DP811)
Applications
R&D lab general purpose test
Quality control and assessment
Provide pure power for RF/MW circuits or components
Provide power for automobile electronic circuit test
Production automation test
Device or circuit characteristic verification and troubleshooting
Educational experiment
Page 3
Model/Order No.
DP832A
DP832
DP831A
DP831
CH1: 0 to 30V/0 to 3A
CH3: 0 to 5V/0 to 3A
CH1: 0 to 8V/0 to 5A
CH3: 0 to -30V/0 to 2A
Isolation between Channels
CH1||CH2,CH3
CH1||CH2,CH3
Max. Total Power
195W
160W
Normal
Voltage
Normal
Current
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Programming
(25℃±5℃)
Readback
(25℃±5℃)
Voltage
1mV/1mV/1mV
10mV/10mV/10mV
1mV/1mV/1mV
1mV/10mV/10mV
Current
1mA/1mA/1mA
1mA/1mA/1mA
0.3mA/0.1mA/0.1mA
1mA/1mA/1mA
Less than 50μs for output voltage to recover to within 15mV following a change in
output current from full load to half load or vice versa.
Model/Order No.
DP821A
DP821
DP822A
DP822
CH1: 0 to 60V/0 to 1A
CH2: 0 to 8V/0 to 10A
CH1: 0 to 20V/0 to 5A
CH2: 0 to 5V/0 to 16A
Isolation between Channels
CH1||CH2
Max. Total Power
140W
180W
Normal
Voltage
Normal
Current
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Programming
(25℃±5℃)
Selecting Procedures
You can select the desired model of power supply and options according to the actual need. The procedures are
as follows.
1. Select the proper model
Three-channel models
Channel Output
Ripples and
Mode
Noise
(20Hz to 20MHz)
Mode
Load Regulation
Rate
Linear
Regulation Rate
Voltage
Annual Accuracy
Current
Voltage
Annual Accuracy
Current
Programming
Resolution
Transient Response Time
[1]
Note
: CH1/CH2/CH3.
Dual-channel models
CH2: 0 to 30V/0 to 3A
CH2: 0 to 30V/0 to 2A
<350μVrms/2mVpp
<2mArms
[1]
0.05%+20mV/0.05%+20mV/0.1%+5mV 0.1%+5mV/0.05%+20mV/0.05%+20mV
[1]
0.2%+5mA/0.2%+5mA/0.2%+5mA 0.2%+10mA/0.2%+5mA/0.2%+5mA
[1]
0.05%+10mV/0.05%+10mV/0.1%+5mV 0.1%+5mV/0.05%+10mV/0.05%+10mV
[1]
0.15%+5mA/0.15%+5mA/0.15%+5mA 0.2%+10mA/0.1%+5mA/0.1%+5mA
[1]
[1]
Channel Output
Ripples and
Mode
<350μVrms/2mVpp
Noise
(20Hz to 20MHz)
Mode
<2mArms
Load Regulation
Rate
Linear
Regulation Rate
[2]
Annual Accuracy
Voltage
Current
0.1%+25mV/0.05%+10mV
[2]
0.2%+10mA/0.2%+10mA
Page 4
Readback
Annual Accuracy
(25℃±5℃)
Voltage
1mV/1mV
10mV/10mV
1mV/1mV
10mV/10mV
Current
0.1mA/1mA
1mA/10mA
1mA/1mA
10mA/10mA
Less than 50μs for output voltage to recover to within 15mV following a change in
output current from full load to half load or vice versa.
Model/Order No.
DP811A
DP811
DP813A
DP813
Range1: 0 to 20V/0 to 10A
Range2: 0 to 40V/0 to 5A
Range1: 0 to 8V/0 to 20A
Range2: 0 to 20V/0 to 10A
Max. Total Power
200W
Normal
Voltage
Normal
Current
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Voltage
<0.01%+2mV
Current
<0.01%+250μA
Programming
(25℃±5℃)
Readback
(25℃±5℃)
Voltage
1mV
10mV
1mV
10mV
Current
0.5mA
10mA
1mA
10mA
Less than 50μs for output voltage to recover to within 15mV following a change in
output current from full load to half load or vice versa.
Option
Function Description
Order No.
You can extend a GPIB interface via the USB HOST interface at the
between the instrument and PC via the GPIB interface.
Programming
Resolution
Transient Response Time
[2]
Note
: CH1/CH2.
Single-channel models
Channel Output
Voltage
Current
[2]
0.1%+25mV/0.05%+5mV
[2]
0.15%+10mA/0.15%+10mA
[2]
[2]
Ripples and
Noise
(20Hz to 20MHz)
Load Regulation
Rate
Linear
Regulation Rate
Annual Accuracy
Annual Accuracy
Programming
Resolution
Transient Response Time
Mode
Mode
Voltage 0.05%+10mV
Current 0.1%+10mA
Voltage 0.05%+10mV
Current 0.1%+10mA
<350μVrms/3mVpp
<2mArms
2. Select and order the options
DP832A/DP831A/DP822A/DP821A/DP813A/DP811A
For these models, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all standard functions. You can select and order the following option
according to your need.
USB to GPIB Interface
Converter
rear panel of the instrument using this module. Then, connect the
instrument to the PC using a GPIB cable to realize the communication
DP832/DP831/DP822/DP821/DP813/DP811
For these models, the high-resolution setting, trigger, monitor, analyzer as well as the RS232 and LAN
communication functions are all optional functions. You can select and order the following options
according to your need.
Note: To install the high-resolution option, digital I/O option, on-line monitor and analysis option as well as the RS232 and
LAN communication interfaces option, you need to get the corresponding option license. For the acquisition method of the
option license and the installation procedures of the options, refer to the corresponding specific manual (you can download
the manual from RIGOL official website (www.rigol.com).
USB-GPIB
Page 5
Option
Function Description
Order No.
Provide high-resolution setting. When DP832, DP831, DP822, DP821,
DP821A, DP813A, and DP811A respectively.
When this option is installed, you can use the trigger and the
the output channel) meets the preset trigger condition.
After this option is installed, you can use the monitor and analyze r.
parameters, such as the average, VAR and range).
After this option is installed, you can use the RS232 or LAN interface
the LAN interface).
You can extend a GPIB interface via the USB HOST interface at the
between the instrument and PC via the GPIB interface.
Option
Function Description
Order No.
DP800 Series Rack Mount
Kit (Single Instrument)
DP800 Series Rack Mount
Kit (Two Instruments)
Install two instruments into a standard 19-inch machine cabinet side
by side.
Option
Function Description
Order No.
DP800 Series Red Safety
Plug
DP800 Series Black Safety
Plug
DP800 Series Green
Safety Plug
High-resolution Option
Digital I/O Option
On-line Monitor and
Analysis Option
RS232 and LAN
Communication
Interfaces Option
DP813, and DP811 are installed with this option, their resolution
specifications are the same with those of DP832A, DP831A, DP822A,
instrument supports trigger input and trigger output. Insert the
Digital I/O interface connecting terminal into the Digital I/O interface
at the rear panel of the instrument; at this point, the instrument
provides 4 trigger input and output channels.
Trigger input: the data cable of the Digital I/O interface can receive
external trigger signals; the source under control (namely the output
channel) will turn on/off the output or invert the output status when
the preset trigger condition is met.
Trigger output: the data cable of the Digital I/O interface outputs
level or square signal when the output of the control source (namely
Monitor: monitor the output status of the instrument. The instrument
will execute the corresponding operation according to the current
setting when the user-defined monitor condition is met.
Analyzer: analyze the files recorded and provide the analysis results
of the channel voltage, current and power (include various statistic
to control the instrument remotely.
RS232: connect the instrument to the PC using a RS232 cable via the
RS232 interface at the rear panel of the instrument (namely the
instrument can communicate with the PC via the RS232 interface).
LAN: connect the instrument to the PC or the local network of the PC
using a network cable via the LAN interface at the rear panel of the
instrument (namely the instrument can communicate with the PC via
HIRES-DP800
DIGITALIO-DP800
AFK-DP800
INTERFACE-DP800
USB to GPIB Interface
Converter
rear panel of the instrument using this module. Then, connect the
instrument to the PC using a GPIB cable to realize the communication
3. Select and order the rack mount kit
Install a single instrument into a standard 19-inch machine cabinet. RM-1-DP800
4. Select and order the safety plug
Provide better insulation protection for users.
Note: For the detailed information of the optional accessories, please refer to the corresponding specific manual (you can
download the manual from RIGOL official website (www.rigol.com).
USB-GPIB
RM-2-DP800
SPR-DP800
SPB-DP800
SPG-DP800
Page 6
Ordering Information
Description
Order No.
Programmable Linear DC Power Supply (Three-channel)
DP832A
Programmable Linear DC Power Supply (Three-channel)
DP832
Programmable Linear DC Power Supply (Three-channel)
DP831A
Programmable Linear DC Power Supply (Three-channel)
DP831
Programmable Linear DC Power Supply (Dual-channel)
DP822A
Programmable Linear DC Power Supply (Dual-channel)
DP822
Programmable Linear DC Power Supply (Dual-channel)
DP821A
Programmable Linear DC Power Supply (Dual-channel)
DP821
Programmable Linear DC Power Supply (Single-channel)
DP813A
Programmable Linear DC Power Supply (Single-channel)
DP813
Programmable Linear DC Power Supply (Single-channel)
DP811A
Programmable Linear DC Power Supply (Single-channel)
DP811
Power Cord
--
CB-USBA-USBB-FF-1
50
Fuse 50T-032H 250V 3.15A
Fuse 50T-025H 250V 2.5A (DP831A/DP831/DP821A/DP821)
Short-circuit Equipment
(DP822A/DP822/DP821A/DP821/DP813A/DP813/DP811A/DP811)
Te r m i n a l -Digital
I/O-DP800
Provide high-resolution setting (for DP832/DP831/DP822/DP821/DP813/DP811; for
the other models, this is a standard accessory)
Provide 4 trigger input and output channels (for
accessory)
Provide on-line monitor and analysis functions (for
accessory)
Provide RS232 and LAN communication interfaces (for
accessory)
USB to GPIB Interface Converter
USB-GPIB
DP800 Series Rack Mount Kit (Single Instrument)
RM-1-DP800
DP800 Series Rack Mount Kit (Two Instruments)
RM-2-DP800
DP800 Series Red Safety Plug
SPR-DP800
DP800 Series Black Safety Plug
SPB-DP800
DP800 Series Green Safety Plug
SPG-DP800
Models
USB Cable
Standard
Accessories
Optional
Accessories
(DP832A/DP832/DP822A/DP822/DP813A/DP813/DP811A/DP811)
Digital I/O Interface Connecting Terminal
DP832/DP831/DP822/DP821/DP813/DP811; for the other models, this is a standard
DP832/DP831/DP822/DP821/DP813/DP811; for the other models, this is a standard
DP832/DP831/DP822/DP821/DP813/DP811; for the other models, this is a standard
--
--
HIRES-DP800
DIGITALIO-DP800
AFK-DP800
INTERFACE-DP800
Loading...