Ricoh MFSP3510SF1 User Manual
1
Model No.
Information
Introduction
This manual contains detailed instructions and notes on the operation and use
of this machine. For your safety and benefit, read this manual carefully before
using the machine. Keep this manual in a handy place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event
will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
-Note
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please
contact your local dealer.
Depending on which country you are in, certain units may be optional. For
details, please contact your local dealer.
Caution
Use of controls or adjustments or performance of procedures other than those
specified in this manual might result in hazardous radiation exposure.
For good print quality, the manufacturer recommends that you use genuine
toner from the manufacturer.
The manufacturer shall not be responsible for any damage or expense that
might result from the use of parts other than genuine parts from the manufacturer with your office products.
Draft 2011/08/29
2
Notes
The model names of the machines do not appear in the following pages. Check
the type of your machine before reading this manual. (For details, see "ModelSpecific Information", User Guide in the manuals CD-ROM.)
Model type Model name Type of ADF
Type 1 SP 3500SF ADF
Type 2 SP 3510SF ARDF
Certain types might not be available in some countries.
Two kinds of size notation are employed in this manual. With this machine
refer to the inch version.
Power Source
120 V, 10 A, 60 Hz
Please be sure to connect the power cable to a power source as above.
Draft 2011/08/29
3
Laws and Regulations
Legal Prohibition
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, pass-
ports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume
no responsibility for its completeness or accuracy. If you have any questions
concerning the legality of copying or printing certain items, consult with your
legal advisor.
This machine is equipped with a function that prevents making counterfeit
bank bills. Due to this function the original images similar to bank bills may
not be copied properly.
Laser Safety
CDRH Regulations
This equipment complies with requirements of 21 CFR subchapter J for class
I laser products. This equipment contains four AlGaAs laser diodes, 6.2-mil-
liwatts, 770-795 nanometer wavelength for each emitter. The beam divergence
angle is 25 degrees (minimum) and 38 degrees (maximum) in the vertical direc-
tion, and 8 degrees (minimum) and 14 degrees (maximum) in the horizontal
direction, and laser beams are generated in Continuous Wave (CW) mode.
Caution:
Use of controls or adjustments or performance of procedures other than those
specified in this manual might result in hazardous radiation exposure.
Draft 2011/08/29
レーザーダイオードの半導体素子/電力値/波長/放射角に
ついてご教示ください。
4
Safety During Operation
In this manual, the following important symbols are used:
WARNING: R
Indicates a potentially hazardous situation which, if instructions are not followed,
could result in death or serious injury.
CAUTION: R
Indicates a potentially hazardous situation which, if instructions are not followed,
may result in minor or moderate injury or damage to property.
Environments Where the Machine Can be Used
WARNING: R
Do not use flammable sprays or solvents in the vicinity of this ma-•
chine. Doing so could result in fire or electric shock.
Do not place vases, plant pots, cups, toiletries, medicines, small metal •
objects, or containers holding water or any other liquids, on or close
to this machine. Fire or electric shock could result from spillage or if
such objects or substances fall inside this machine.
CAUTION: R
Keep the machine away from humidity and dust. Otherwise a fire or an •
electric shock might occur.
Do not place the machine on an unstable or tilted surface. If it topples over, •
an injury might occur.
Do not place heavy objects on the machine. Doing so can cause the ma-•
chine to topple over, possibly resulting in injury.
Keep the machine in an area that is within optimum environmental condi-•
tions. Operating the machine in an environment that is outside the recommended ranges of humidity and temperature can cause an electrical fire
hazard. Keep the area around the socket free of dust. Accumulated dust
can become an electrical fire hazard.
Make sure the room where you are using the machine is well ventilated •
and spacious. Good ventilation is especially important when the machine is
used heavily.
Draft 2011/08/29
5
Do not obstruct the machine's vents. Doing so risks fire caused by over-•
heated internal components.
Machine sound levels exceeding [Sound Power Level (Black and White)] > •
63 dB(A) are not suitable for desk work environments, so place the machine in another room.
Keep the machine away from salt-bearing air and corrosive gases. Also, do •
not install the machine in places where chemical reactions are likely (laboratories, etc.), as doing so will cause the machine to malfunction.
Handling Power Cords and Power Plugs
WARNING: R
Do not use any power sources other than those that match the speci-•
fications shown in this manual. Doing so could result in fire or electric
shock.
Do not use any frequencies other than those that match the specifica-•
tions shown. Doing so could result in fire or electric shock.
Do not use multi-socket adaptors. Doing so could result in fire or •
electric shock.
Do not use extension cords. Doing so could result in fire or electric •
shock.
Do not use power cords that are damaged, broken, or modified. Also, •
do not use power cords that have been trapped under heavy objects,
pulled hard, or bent se verely. Doing so could result in fire or electric
shock.
Be sure to disconnect the plug from the wall outlet at least once a •
year.
There are burn marks on the plug.•
The prongs on the plug are deformed.•
If any of the above conditions exist, do not use the plug and consult
your dealer or service representative. Use of the plug could result in
fire or electric shock.
Touching the prongs of the power cable's plug with anything metallic •
constitutes a fire and electric shock hazard.
最新の内容に修正予定です。
（Id130）
次回UserGuideの表記に合わせます。
Draft 2011/08/29
6
The supplied power cord is for use with this machine only. Do not use •
it with other appliances. Doing so could result in fire or electric shock.
It is dangerous to handle the power cord plug with wet hands. Doing •
so could result in electric shock.
CAUTION: R
Be sure to push the plug of the power cord fully into the wall outlet. Par-•
tially inserted plugs create an unstable connection that can result in unsafe
buildup of heat.
If this machine is not going to be used for several days or longer at a time, •
disconnect its power cord from the wall outlet.
When performing maintenance on the machine, always disconnect the •
power cord from the wall outlet.
When disconnecting the power cord from the wall outlet, always pull the •
plug, not the cord. Pulling the cord can damage the power cord. Use of
damaged power cords could result in fire or electric shock.
Be sure to disconnect the plug from the wall outlet and clean the prongs •
and the area around the prongs at least once a year. Allowing dust to build
up on the plug constitutes a fire hazard.
Handling the Machine
WARNING: R
Be sure to locate the machine as close as possible to a wall outlet. •
This will allow easy disconnection of the power cord in the event of
an emergency.
If the machine emits smoke or odours, or if it behaves unusually, you •
must turn off its power immediately. After turning off the power, be
sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use
the machine. Doing so could result in fire or electric shock.
If metal objects, or water or other fluids fall inside this machine, you •
must turn off its power immediately. After turning off the power, be
sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use
the machine. Doing so could result in fire or electric shock.
Draft 2011/08/29
Loading...