Modified Article: Parts Catalog CorrectionPrepared by: S. Hizen
From: QAC 1st Field Information Dept.
Reason for
Modification:
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
To meet standards
( )
(No serial number cut-in information)
Please correct your parts catalog as follows.
Page 45
1. Please correct the following part number.
Old partNew partDescriptionIndex
numbernumber
A153 2303Grounding Plate34
A153 2302Drum Bearing Holder34
2. Please add the following part number.
New partDescriptionQtyIndex
number
A153 2301Front Stay135
RICOHModification BulletinPAGE: 2/2
Model: Phoenix II (Eagle2)Date: 15-Jul-97
Page 82
Please add the following illustration to your parts catalog.
No: 1
RICOHModification BulletinPAGE: 1/1
Model: Phoenix II (Eagle II)Date: 31-Jul-97
Modified Article: Parts Catalog CorrectionPrepared by: S. Hizen
From: QAC 1st Field Information Dept.
Reason for
Modification:
Page 19
The illustration and the index was not linked.
Please change as follows.
Part numberDescriptionQtyIndex
AF02 0330Vertical Driven Roller
AA08 0034
Please add the following parts.
Bushing - 4×5×76 → 4
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
6 → 2
36
37
No: 2
To meet standards
( )
New partDescriptionQtyIndex
number
AA06 3538Spring - 10 mm440
0720 0030ERetaining Ring - M3-106
OLDNEW
→→
*
*
*
*
*
***
RICOHModification BulletinPAGE: 1/1
Model: Phoenix II (Eagle II)Date: 31-Aug-97
Modified Article: Parts Catalog CorrectionPrepared by: S.Hizen
From: QAC 1st Field Information Dept.
Reason for
Modification:
The following OLD part number was not announced. (The new part number A2045181 is
already listed in the printed Parts Catalog.)
The reason for this change was to comply with safety regulations in Taiwan.
Old partNew partDescriptionIntPageIndex
numbernumber
A204 5111A204 5181 Main Control Board (EU/ASIA/TWN)X/O712
NOTE: For all machines except in Taiwan, the old part may be used.
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
No: 3
To meet standards
( )
81*
M
Model:
Phoenix II (Eagle II)
odification
B
Date:
ulletin
31-Aug-97
No:
PAGE: 1/1
4
Modified Article:
From:
Reason for
Modification:
The description of the seal in the development unit is incorre ct. Please correct your Part
Catalog as follows.
The seal has also been changed in size to standardize with other models.
QAC 1st Field Information Dept.
partIncorrect CorrectQtyIntPageIndex Note
numberDescriptionDescription
AA150231Seal – 15x30Seal – 15x32--4120-
Old partNew partDescriptionQtyIntPageIndexNote
numbernumber
AA150231Seal – 15x32
Seal in the Development Unit
Parts catalog correction
To facilitate assembly
Part standardization
AA150408 Seal – 15x341O/O4120
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
S.Hizen
( )
Seal 15x34
M
Model:
Phoenix II (Eagle II)
odification
B
Date:
ulletin
15-Sep-97
No:
PAGE: 1/1
5
Modified Article:
From:
Reason for
Modification:
Page 23
Please change the following description.
Part numberOld DescriptionNew DescriptionIndex
Please add the following part number.
Part numberDescriptionQtyIndex
Page 35
Please change the following description.
QAC 1st Field Information Dept.
A206 2651Bypass Feed UnitBypass Feed Unit (A206/A207)*
A134 2651Bypass Feed Unit (A204)1*
Parts Catalog Correction
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
J.Kasamoto
( )
Old partOld DescriptionNew DescriptionIndex
number
A153 19033rd Scanner Ass`y3rd Scanner Bracket31
M
Model:
PhoenixII (EagleII)
odification
B
Date:
ulletin
15-Nov-97
No:
PAGE: 1/1
6
Modified Article:
From:
Reason for
Modification:
Please delete the following part number from the parts list, and change the call out
number in the illustration as sh own.
Part numberDescriptionQtyPageIndex
QAC Field Information Dept.
A155 5314LCT Relay Harness12124
Parts Catalog
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
M. Kitajima
( )
Please add the following part to your parts catalog.
New partDescriptionQtyPageIndex
number
A155 5314LCT Relay Harness17121
M
Model:
Phoenix II (Eagle II)
odification
ulletin
B
Date:
15-Dec-97
No:
PAGE: 1/1
7
Modified Article:
From:
Reason for
Modification:
Please change following the part number.
QAC Field Information Dept.
Old part New part Description Qty PageIndex
number number
A134 2952 Universal Tray 1 17 20
Parts Catalog
Parts catalog correction
To facilitate assembly
Part Standardization
Parts catalog correction
To facilitate assembly
Part Standardization
Vendor change
To improve reliability
Other
Toner Bottle Drive
Toner Bottle Drive
Prepared by:
To meet standards
(RIC EU)
(RIC NA)
J. Kasamoto
( )
39*
39*
M
Model:
Phoenix II (Eagle II)
odification
ulletin
B
Date:
15-Apr-98
No:
PAGE: 1/3
10
Modified Article:
From:
Reason for
Modification:
The type of bushing used on the transfer belt drive roller has been changed. This is to
prevent the transfer unit casing from cracking as a result of the oil included in the bearing.
QAC Field Information Dept.
Old part New part Description Qty Int PageIndexNote
Parts catalog correct ion
To facilitate assembly
Part standardization
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
M.Kitajima
( )
M
Model:
MODEL NAMEV/HzDESTINATIONCODESERIAL NUMBER
Phoenix II (Eagle II)
odification
B
Date:
ulletin
15-Apr-98
JAPAN PRODUCTION
No:
PAGE: 2/3
10
Gestetner 2740Z
nashuatec 3740
Savin 9400
Savin 9400115/60USA, CanadaA204- 15From First Production
Ricoh FT5640115/60USA, CanadaA204- 17From First Production
Ricoh FT5640110/60Taiwan, SaudiA204- 19A7447070001
Gestetner 2740Z
nashuatec 3740
Rex Rotary 8740Z
Infotec 5403Z220. 230,
Ricoh FT5640220. 230,
Ricoh FT5640220/50Asia, Middle EastA204- 29A7447060130
Gestetner 2740z110/60TaiwanA204- 50From First Production
Ricoh FT5640220/50ChinaA204- 69From First Production
Gestetner 2740ZT
naashuatec 3740T
Savin 9400L
Savin 9400L115/60USA, CanadaA206- 15From First Production
Ricoh FT5740115/60USA, Canada,A206- 17From First Production
115/60USA, Canada,
L. America
220. 230,
240/50
240/50
240/50
115/60USA, Canada,
Europe, etc.A204- 22AL17070001
EuropeA204- 263N50870001
EuropeA204- 27A7447080021
L. America
A204- 10AK47070001
A206- 10From First Production
Ricoh FT5740110/60Taiwan, SaudiA206- 19From First Production
Gestetner 2740ZT
The material of the rear guide plate has been changed to prevent the guide from being
worn. If it is worn, paper misfeeds and noise may occur.
QAC Field Information Dept.
Old partNew partDescriptionQtyIntPageIndex Note
numbernumber
A1532560A2042560Rear Guide Plate1 - 1X/O2319
Rear Guide Plate
Parts catalog correction
To facilitate assembly
Part standardization
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
( )
Rear Guide Plate
M.Kitajima
M
Model:
MODEL NAMEV/HzDESTINATIONCODESERIAL NUMBER
Phoenix II (Eagle II)
odification
B
Date:
ulletin
15-Apr-98
JAPAN PRODUCTION
No:
PAGE: 2/3
11
Gestetner 2740Z
nashuatec 3740
Savin 9400
Savin 9400115/60USA, CanadaA204- 15From First Production
Ricoh FT5640115/60USA, CanadaA204- 17From First Production
Ricoh FT5640110/60Taiwan, SaudiA204- 19A7447090001
Gestetner 2740Z
The notch has been extended on the metal plate of the vibrating plate as shown in the
Illustration below to reduce the possibility of the mylar bending.
QAC Field Information Dept.
Old part New part Description Qty Int PageIndexNote
number number
A1544623 A1544626Vibrating Plate 2 - 2 X/O 57 16
Vibrating Plate
Parts catalog correct ion
To facilitate assembly
Part standardization
Vendor change
To improve reliability
Other
Mylar
Prepared by:
To meet standards
M.Kitajima
( )
∗
Ð
Notch
OLD
NEW
M
Model:
Phoenix II (Eagle II)
MODEL NAMEV/HzDESTINATIONCODESERIAL NUMBER
odification
B
Date:
ulletin
15-Apr-98
JAPAN PRODUCTION
No:
PAGE: 2/3
12
Gestetner 2740Z
nashuatec 3740
Savin 9400
Savin 9400115/60USA, CanadaA204- 15From First Production
Ricoh FT5640115/60USA, CanadaA204- 17From First Production
Ricoh FT5640110/60Taiwan, SaudiA204- 19A7447110001
Gestetner 2740Z
Parts catalog correction
To facilitate assembly
Part standardization
Vendor change
To improve reliability
Other
Prepared by:
To meet standards
M.Kitajima
( )
Problem
If the power is turned on when the front cover is open, the front cover is then closed and
the start key is pressed, SC440 occurs.
Cause
Due to the change to the inner circu it of the main motor to improve the reliability of the
motor, the current software cannot recognize this modified mo tor correctly, resulting in the
SC440 display.
Due to parts standardization with the Swallow II, the timing pulley has been changed.
Since the new timing pulley cannot be supplied separately, assembly parts are provided.
Because of this change , the Retaining Ring – M4 (Index 102) is no longer used. When
replacing the old timing pulley, make sure to check whether you have the correct part
(front or rear).
Please note that the cut-in serial number is not recorded due to parts standardization.
30
*
29
*
RICOHModification
Model:
Phoenix II (Eagle II ) (Chinese Version only)
Bulletin
Date:
31-Aug-98
No:
PAGE: 1/3
18
Modified Article:
From:
Reason for
Modification:
The main switch decal for the Chinese version has been changed from the English version
to a Chinese version.
QAC Field Information Dept.
Old partNew partDescriptionQtyIntPageIndex Note
numbernumber
AA001373Decal – Main Switch1-0X/928
AA001373Decal – Main Switch1-0X/832
Decal - Main Switch
Parts catalog correction
To facilitate assembly
Part Standardization
A2041349Decal – Main Switch – Chinese0-1 /0928
A2041349Decal – Main Switch – Chinese0-1 /0832
Model:
Modified Article:
From:
Reason for
Modification:
To reduce no-feed jams from the duplex unit caused by insufficient pressure from the
bottom plate, the shape of the spring clutch has been changed. To distinguish between the
old and new clutches, the colour of the sleeve has been changed from white to blue.
The insufficient pressure occurs when the clutch turns in the direction which tightens the
spring because the sleeve hits the spring hook. As a result, the spring cannot turn
completely, so the bottom plate cannot be lifted up to the highest position.
To prevent the sleeve from hitting the spring hook, 4.5 mm has been cut from the sleeve
as shown.
Phoenix II (Eagle II)
Spring Clutch - Duplex Tray Bottom Plate
QAC Field Information Dept.
Parts catalog correction
To facilitate assembly
Part standardization
Reissue date:
The items in bold italics have been corrected or added.
Model:
Phoenix II (Eagle II)
30-Sep-98
Date:
15-Sep-98
No:
PAGE: 1/3
21
Modified Article:
From:
Reason for
Modification:
To improve the durability of the screw holes for the main reflector, the screw holes have
been changed from the tapping screw type to the pan head screw type. However, the
screws #101 which hold the exposure adjusting plates (#8) have not been changed.
QAC Field Information Dept.
Old partNew partDescriptionQtyIntPageIndex Note
numbernumber
A1531774
Reflector - Main
Parts catalog correction
To facilitate assembly
Part standardization
03140060BPhillips Pan Head Screw – M4x6n-n-1X/51107X/O
Phoenix II (Eagle II)
Fusing Front Side Plate
QAC Field Information Dept.
Parts catalog correction
To facilitate assembly
Part standardization
Old part
number
A2044101 A2044095Front Side Plate1-1X/X5114
A2044312 A2044313Stripper Pawl Bracket1-1X/X4918
New part
DescriptionQtyIntPageIndex Note
number
AA143331Stepped Screw – N4x7.50-1 /X51
Date:
15-Sep-98
Prepared by:
Vendor change
To improve reliability
Other
No.:
22
M.Kitajima
To meet standards
( )
*
33
New Index
*
as a set
Since the cleaning roller bracket (P/N: A2044270) and the stripper pawl bracket are
attached to the front and rear side plates with screws, the front and/or rear side plate(s)
may lean to the inside. This may cause a knocking/clicking noise. To keep both the side
plates in the proper position, one of the screws which secures the cleaning roller bracket
has been changed to a stepped screw. Because of this change, the screw hole in the front
side plate has changed from f4 to f5. Also, the screw hole shape of the stripper pawl
bracket has been changed from a circular hole to a long hole.