Ricoh Aficio 3224C SPF, C2410, DSc424, LD124c, C3210e Printer Reference
...
Operating Instructions
Printer Reference
Getting Started
Preparing the Machine
Setting Up the Printer Driver
Other Print Operations
Printer Features
Using the Document Server
Paper type: OK Prince Eco G100(55kg), Paper Thickness=80 µm // Pages in book=156 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.240000 mm
Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its
completeness or accuracy. If you have any questions concerning the legality of copying or printing certain items, consult with your legal advisor.
Warning
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
Trademarks
Microsoft
®
, Windows® and Windows NT® are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe
®
, PostScript®, Acrobat®, PageMaker® and Adobe Type Manager are registered trademarks of
Adobe Systems Incorporated.
PCL® is a registered trademark of Hewlett-Packard Company.
AppleTalk, Apple, Macintosh and Mac OS are registered trademarks of Apple Computer, Incorporated.
IPS-PRINT™ Printer Language Emulation Copyright
©
2000, Oak Technology, Inc., All Rights Reserved.
UNIX is a registered trademark in the United States and other countries, licensed exclusively through
X/Open Company Limited.
Bluetooth
®
is a registered trademark of Bluetooth-SIG Inc. worldwide.
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows
®
95 is Microsoft® Windows® 95
• The product name of Windows
®
98 is Microsoft® Windows® 98
• The product name of Windows® Me is Microsoft® Windows® Millennium Edition (Windows Me)
• The product name of Windows
®
2000 are as follows:
Microsoft
®
Windows® 2000 Professional
Microsoft® Windows® 2000 Server
Microsoft
®
Windows® 2000 Advanced Server
• The product name of Windows
®
XP are as follows:
TABLE OF CONTENTS
Manuals for This Machine .....................................................................................1
How to Read This Manual .....................................................................................3
1. Getting Started
Control Panel..........................................................................................................5
Display Panel .............................................................................................................7
User Authentication...............................................................................................9
User Code Authentication (Using the Control Panel).................................................9
User Code Authentication (Using a Printer Driver) ....................................................9
Login (Using the Control Panel).................................................................................9
Logoff (Using the Control Panel)..............................................................................10
Login (Using a Printer Driver)...................................................................................10
Connecting the Machine .....................................................................................11
Requirements...........................................................................................................11
Connecting the machine to the host using a USB cable.......................................... 11
Connecting the Machine to the host
using the parallel cable/IEEE 1394 (SCSI print) cable...........................................12
Connecting to the Ethernet Interface .......................................................................13
Setting Paper on the Bypass Tray......................................................................14
Setting custom size paper........................................................................................16
Setting thick paper or OHP transparencies..............................................................17
2. Preparing the Machine
Quick Install..........................................................................................................19
Confirming the Connection Method...................................................................21
Network Connection.................................................................................................21
Local Connection .....................................................................................................24
Using the SmartDeviceMonitor for Client Port..................................................25
Installing SmartDeviceMonitor for Client..................................................................25
Installing the PCL or RPCS Printer Driver (TCP/IP).................................................26
Installing the PCL or RPCS Printer Driver (NetBEUI) ..............................................28
Installing the PCL or RPCS Printer Driver (IPP) ......................................................30
Changing the Port Settings for SmartDeviceMonitor for Client................................32
Using the Standard TCP/IP Port .........................................................................34
Installing the PCL or RPCS Printer Driver................................................................34
Using the LPR Port ..............................................................................................36
Installing the PCL or RPCS Printer Driver................................................................36
Using as the Windows Network Printer.............................................................38
Installing the PCL or RPCS Printer Driver................................................................38
Using as the NetWare Print Server/Remote Printer..........................................40
Form Feed................................................................................................................42
Banner Page ............................................................................................................42
Printing after Resetting the Printer...........................................................................42
i
Installing the Printer Driver Using USB .............................................................43
Windows 98 SE/Me - USB .......................................................................................43
Windows 2000 - USB...............................................................................................45
Windows XP, Windows Server 2003 - USB.............................................................46
Troubleshooting USB...............................................................................................47
Printing with Parallel Connection.......................................................................48
Installing the PCL or RPCS Printer Driver................................................................48
Installing the Printer Driver Using IEEE 1394 (SCSI print) ...............................50
Windows 2000..........................................................................................................50
Windows XP, Windows Server 2003........................................................................52
Printing with Bluetooth Connection...................................................................54
Supported Profiles....................................................................................................54
Printing with Bluetooth Connection ..........................................................................54
If a Message Appears during Installation..........................................................57
Making Option Settings for the Printer..............................................................58
Conditions for Bidirectional Communication ............................................................58
If Bidirectional Communication is Disabled..............................................................60
Installing Font Manager 2000.............................................................................. 61
Using Adobe PageMaker Version 6.0, 6.5, or 7.0 .............................................. 62
3. Setting Up the Printer Driver
PCL - Accessing the Printer Properties.............................................................63
Windows 95/98/Me - Accessing the Printer Properties ............................................63
Windows 2000 - Accessing the Printer Properties ...................................................64
Windows XP, Windows Server 2003 - Accessing the Printer Properties.................66
Windows NT 4.0 - Accessing the Printer Properties ................................................68
RPCS - Accessing the Printer Properties..........................................................70
Windows 95/98/Me - Accessing the Printer Properties ............................................70
Windows 2000 - Accessing the Printer Properties ...................................................72
Windows XP, Windows Server 2003 - Accessing the Printer Properties.................74
Windows NT 4.0 - Accessing the Printer Properties ................................................76
ii
4. Other Print Operations
Printing a PDF File Directly.................................................................................79
Printing Method........................................................................................................79
Using Locked & Sample Print Job List ..............................................................80
Sample Print.........................................................................................................82
Printing a Sample Print File......................................................................................82
Deleting a Sample Print File.....................................................................................84
Checking the Error Log ............................................................................................84
Locked Print .........................................................................................................86
Printing a Locked Print File ......................................................................................86
Deleting Locked Print Files ......................................................................................87
Checking the Error Log ............................................................................................88
Collate...................................................................................................................89
Printing with the Finisher....................................................................................91
Staple .......................................................................................................................92
Spool Printing ......................................................................................................94
Covers...................................................................................................................95
Slip Sheet..............................................................................................................99
User Defined Pages ...........................................................................................101
Form Feed...........................................................................................................102
Print Using a Selected Tray ...................................................................................102
Canceling Form Feed.............................................................................................103
Canceling a Print Job ........................................................................................104
Windows - Canceling a Print Job ...........................................................................104
5. Printer Features
Printer Features Menu .......................................................................................105
Adjusting Printer Features................................................................................107
Printer Features Parameters.............................................................................108
List / Test Print .......................................................................................................108
Maintenance...........................................................................................................110
System ...................................................................................................................110
Host Interface.........................................................................................................113
PCL Menu ..............................................................................................................113
PS Menu ................................................................................................................115
PDF Menu ..............................................................................................................116
6. Using the Document Server
Accessing the Document Server......................................................................117
iii
7. The Functions and Settings of the Machine
Mainframe...........................................................................................................119
Functions................................................................................................................119
Interface .................................................................................................................119
List of the Setting Items ....................................................................................120
Web Image Monitor................................................................................................120
telnet ......................................................................................................................122
UNIX.......................................................................................................................122
Settings that can be used with PostScript 3...........................................................123
8. Appendix
Software and Utilities Included on the CD-ROM .............................................125
Printer Drivers for This Printer................................................................................126
SmartDeviceMonitor for Admin ..............................................................................128
SmartDeviceMonitor for Client ...............................................................................129
Troubleshooting.................................................................................................131
Error & Status Messages on the Display Panel .....................................................131
Checking the Error Log ..........................................................................................135
The Machine Does Not Print ..................................................................................136
Other Printing Problems.........................................................................................139
System Settings (Parallel Connection)............................................................144
Precautions when using Windows Server 2003.............................................. 145
Precautions when using the Terminal Server mode ..............................................145
Specifications.....................................................................................................146
Options...................................................................................................................147
INDEX....................................................................................................... 150
iv
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
❒ Manuals provided are specific to machine type.
❒ Adobe Acrobat Reader/Adobe Reader is necessary to view the manuals as a
PDF file.
❒ Two CD-ROMs are provided:
• CD-ROM 1“Operating Instructions”
• CD-ROM 2“Scanner Driver and Document Management Utility”
❖❖❖❖ General Settings Guide
Provides an overview of the machine and describes System Settings(such as
Tray Paper Settings), Document Server functions and troubleshooting.
Refer to this manual for Address Book procedures such as registering fax
numbers, e-mail addresses, and user codes.
❖❖❖❖ Security Reference
This manual is for administrators of this machine. It describes security functions that the administrators can use to protect data from being tampered, or
prevent the machine from unauthorized use. Also refer to this manual for the
procedures for registering administrators, as well as setting user and administrator authentication.
❖❖❖❖ Network Guide (PDF file - CD-ROM1)
Provides information about configuring and operating the printer in a network environment or using software. This manual covers all models, and
therefore contains functions and settings that may not be available for your
model.
Images, illustrations, functions, and supported operating systems may differ
from those of your model.
❖❖❖❖ Copy Reference
Describes operations, functions, and troubleshooting for the machine’s copier
function.
❖❖❖❖ Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine's facsimile function.
❖❖❖❖ Facsimile Reference <Advanced Features>
Describes advanced facsimile functions such as line settings and procedures
for registering IDs.
❖❖❖❖ Printer Reference (this manual)
Describes system settings, operations, functions, and troubleshooting for the
machine’s printer function.
1
❖❖❖❖ Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine’s scanner function.
❖❖❖❖ Manuals for DeskTopBinder Lite
DeskTopBinder Lite is a utility included on the CD-ROM labeled “Scanner
Driver and Document Management Utility”.
• DeskTopBinder Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, and the operating environment for DeskTopBinder Lite in detail. This guide can be displayed from the [Setup] dialog
box when DeskTopBinder Lite is installed.
• DeskTopBinder Introduction Guide (PDF file - CD-ROM2)
Describes operations of DeskTopBinder Lite and provides an overview of
its functions. This guide is added to the [Start] menu when DeskTopBinder
Lite is installed.
• Auto Document Link Guide (PDF file - CD-ROM2)
Describes operations and functions of Auto Document Link installed with
DeskTopBinder Lite. This guide is added to the [Start] menu when DeskTopBinder Lite is installed.
❖❖❖❖ Other manuals
• PostScript 3 Supplement (PDF file - CD-ROM1)
• UNIX Supplement (available from an authorized dealer, or as a PDF file on
our Web site)
2
How to Read This Manual
R
R
Symbols
In this manual, the following symbols are used:
WARNING:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
CAUTION:
This symbol indicates a potentially hazardous situation which, if instructions are
not followed, may result in minor or moderate injury, or damage to property.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might misfeed, originals might be damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates prior knowledge or preparation is required before operation.
Note
This symbol indicates precautions for operation, or actions to take after mal-operation.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[]
Keys and buttons that appear on the computer's display.
Keys that appear on the machine's display panel.
{}
Keys built into the machine's control panel.
Keys on the computer's keyboard.
3
4
Control Panel
1. Getting Started
AEU041S
1.
Indicators
Displays errors and machine status.
d: Add Staple indicator
D: Add Toner indicator
B: Load Paper indicator
L: Service Call indicator
M: Open Cover indicator
x: Misfeed indicator
See "Control Panel", General Settings
Guide.
2. {
{User Tools/Counter}}}} key
{{
• User Tools
Press to change default settings and
conditions to your requirements.
• Counter
Press to display or print the total
number of copies made.
3.
Display panel
Displays operation status, error messages, and function menus. See p.7 “Display
Panel”.
4.
{{{{Energy Saver}}}} key
Press to switch to and from Energy Saver
mode.
Note
❒ This key is ineffective during System
Settings (User Tools) operations.
5.
Main power indicator
This indicator lights when the main power switch is turned on.
Important
❒ Do not turn off the main power
switch while the On indicator is lit
or blinking. Doing so may damage
the hard disk.
6.
On indicator
This indicator lights when the operation
switch is turned on.
7.
Operation switch
Press this switch to turn the power on
(the On indicator goes on). To turn the
power off, press this switch again (the On
indicator goes off).
5
1
Getting Started
8.
{{{{Clear/Stop}}}} key
Press to cancel the entered data.
9.
{{{{#}}}} key
Press after entering a value.
10.
Number keys
Press to enter a value for various settings.
11.
Function keys
Press to switch between the “Copy”,
“Document Server”, “Fax”, Printer”, and
“Scanner” screens.
The indicator for the selected function
lights.
12.
Function status indicators
These show the status of the above functions:
• Green: the function is active.
• Red: the function has been interrupted.
13.
mmmm: Data In indicator
The Data In indicator shows the status of
data reception from a computer.
• This indicator blinks when data is being received.
• This indicator lights when there is
data remaining to be printed.
6
Control Panel
Display Panel
This section describes configuration using the display panel when the printer
function is selected.
Important
❒ The machine switches to offline when you make settings when the machine
is online. After you complete the setting, the machine switches to online automatically.
❒ If you make a setting when the machine is offline, it will stay offline after-
ward.
❒ The function items displayed serve as selector keys. You can select or specify
an item by pressing it lightly.
❒ When you select or specify an item on the display panel, it becomes highlighted.
❒ Keys dimmed (for example, ) cannot be used.
1
1.
Operational status or messages
Displays current machine status, such as
"Ready", "Offline", and "Printing...". Information about the print job (user ID
and document name) appears in this section.
2.
[ffffOnline] key / [ Offline] key
When you press these keys, the machine
switches between online and offline.
When the machine is online, it can receive data from the computer.
When the machine is offline, it cannot receive data from the computer.
AEU042S
3.
[Form Feed] key
Press to print all the data left in the machine's input buffer.
Note
❒ When the machine is online, the status
appears dimly.
❒ This function is not available with the
RPCS printer language.
4.
[Job Reset] key
Press to cancel the current print job.
If you press it when the machine is offline
and Hex Dump is selected, Hex Dump is
canceled.
7
Getting Started
1
5. [Locked & Sample Print Job List]
Press to display Locked/Sample Print
jobs sent from a computer.
6. [Error Log]
Press to display the error logs, such as
Locked/Sample Print jobs sent from a
computer.
Note
❒ When the power is turned on, the copier display is shown. This is a factory
default. This initial setting can be changed. See “User Tools (System Settings)”, General Settings Guide.
7. [Spooling Job List]
Press to display spooled jobs.
8. [Paper Tray Status] key
The paper tray settings appear.
8
User Authentication
When user authentication (User Code
Authentication, Basic Authentication,
Windows Authentication, or LDAP
Authentication) is set, the authentication screen is displayed. Unless a valid user name and password are
entered, operations are not possible
with the machine. Log on to operate
the machine, and log off when you
are finished operations. Be sure to log
off to prevent unauthorized users
from using the machine.
Note
❒ Consult the User Administrator
about your login user name, password, and user code. For details
about the various types of user authentication, consult the appropriate administrators.
User Authentication
User Code Authentication
(Using a Printer Driver)
When user authentication is set, specify the user code in the printer properties of a printer driver. For details,
see the printer driver Help.
Login (Using the Control Panel)
Follow the procedure below to log in
when Basic Authentication, Windows
Authentication, or LDAP Authentication is set.
Press [Enter] for [Login User Name].
AAAA
1
❒ For user code authentication, enter
a number that is registered in the
Address Book as a login user name
as the user code.
User Code Authentication
(Using the Control Panel)
When user authentication is set, the
following screen appears.
Enter a user code (eight digit), and
then press [#].
Enter a login user name, and then
BBBB
press [OK].
Press [Enter] for [Login Password].
CCCC
Enter a login password, and then
DDDD
press [OK].
Press [Login].
EEEE
When the user is authenticated, the
screen for the function you are using appears.
9
1
Getting Started
Logoff (Using the Control Panel)
Follow the procedure below to log off
when Basic Authentication, Windows
Authentication, or LDAP Authentication is set.
Press {{{{User Tools/Counter}}}} key.
AAAA
Press [→→→→ Logout
BBBB
Press [Yes].
CCCC
Press {{{{User Tools/Counter}}}} key.
DDDD
].
Login (Using a Printer Driver)
When Basic Authentication, Windows Authentication, or LDAP Authentication is set, make encryption
settings in the printer properties of a
printer driver, and then specify a
login user name and password. For
details, see the printer driver Help.
Note
❒ When logged on using a printer
driver, logging off is not required.
10
Connecting the Machine
Connecting the Machine
Reference
For information about connection
using Ethernet and wireless LAN,
see "Confirming the Connection",
Network Guide.
For information about connection
using Bluetooth, see the manual
that comes with the optional Bluetooth interface unit.
Requirements
Before using this machine, make sure
all environmental and electrical requirements are met. Connect the machine to the host computer using the
parallel port, network interface unit,
or both.
Make sure all cables, connectors, and
electrical outlets necessary to attach
the machine to the host computer or
network are at hand.
Connecting the machine to the
host using a USB cable
Connect the USB 2.0 interface ca-
AAAA
ble to the USB port.
Connect the other end to the USB
BBBB
port on the host computer.
Note
❒ The USB 2.0 interface board is
supported by Windows 98
SE/Me/2000/XP, Windows
Server 2003, Mac OS X or higher.
• For Windows 98 SE/Me:
Make sure to install “USB
Printing Support”. If USB 2.0
is used with Windows 98
SE/Me, only a speed equal to
that of USB 1.1 is possible.
1
AGP001S
You can connect the machine to the
host computer using a USB interface
cable.
This machine does not come with a
USB interface cable. Make sure you
purchase the appropriate cable for the
machine and your computer.
Follow the procedure below to connect the machine to the host computer
using a USB interface cable.
• For Mac OS:
To use Macintosh, the machine must be equipped with
the optional PostScript 3
unit. Mac OS supports only
the standard USB port. If
USB 2.0 is used with a Mac
OS, only a speed equal to that
of USB 1.1 is possible.
11
1
Getting Started
Connecting the Machine to the
host using the parallel cable/IEEE
1394 (SCSI print) cable
Connect the machine to the host computer using the optional parallel
board or optional IEEE 1394 interface
board. This machine does not come
with a parallel cable to connect the
machine to the host computer.
The machine's parallel interface is a
standard bidirectional interface. It requires a standard IEEE 1284 compliant 36-pin parallel cable and a parallel
port on the host computer. Make sure
you purchase the appropriate cable
for the machine and your computer.
Turn off the main power switches
AAAA
of the machine and computer.
Important
❒ Before turning off the main pow-
er switch, see “Turning Off the
Power”, General Settings Guide.
Plug the cable into the connector
BBBB
on the machine’s interface.
❖❖❖❖ Parallel Connection
Note
❒ Do not use a parallel cable that is
longer than 3 meters (10 feet).
❒ Rating voltage of the interface con-
nector: Max. DC 5V
Follow the procedure below to connect the machine to the host computer
using a parallel cable or IEEE 1394 interface cable.
Important
❒ Before connecting the machine and
a computer using an interface cable, make sure the machine is not
operating, and then turn off the
main power switches of the machine and computer.
❒ Be sure to use a specified interface
cable. Other cables may cause radio interference.
❖❖❖❖ IEEE 1394 (SCSI print) Connection
Plug the other end of the cable
CCCC
into the connector on the computer’s interface.
Turn on the machine's main pow-
DDDD
er switch.
AGP002S
AGP003S
12
Connecting the Machine
Turn on the computer.
EEEE
Note
❒ When using Windows 95/98/
Me/2000/XP and Windows
Server 2003, a printer driver installation screen might appear
when the computer is turned
on. If this happens, click [Cancel]
on the screen. For more information, see p.19 “Preparing the
Machine”.
The machine and computer are
now connected. The printer driver
must be installed next. For information about how to install the
printer driver, see p.19 “Preparing
the Machine”.
Connecting to the Ethernet
Interface
Turn off the main power switch.
BBBB
Important
❒ Make sure the main power is
off. See "Turning On the Power", General Settings Guide.
Connect the Ethernet cable to the
CCCC
10 BASE-T / 100 BASE-TX port.
Turn on the main power switch.
DDDD
1
AGP014S
The network interface board supports
10 BASE-T or 100 BASE-TX connections.
Important
❒ Before making the connection, touch
the metallic part to ground yourself.
A core for the Ethernet cable is
AAAA
supplied with this machine. The
Ethernet cable loop should be
about 15 cm (6 in.) (AAAA) from the
machine end of the cable.
ZKRH050E
1.
Indicator (green)
Remains green when the machine is
properly connected to the network.
2.
Indicator (yellow)
Turns yellow when 100 BASE-TX is
operating. Turns off when 10 BASE-T
is operating.
AEV047S
13
Getting Started
Setting Paper on the Bypass Tray
1
This section gives instructions for setting paper on the bypass tray. Use the
bypass tray to print onto OHP transparencies, labels, thick paper, and envelopes that cannot be loaded in the
paper tray.
Reference
For details about setting paper in
the regular paper tray, see General
Settings Guide.
Note
❒ When loading letterhead paper,
pay attention to its orientation. See
“Orientation-Fixed Paper or TwoSided Paper”, General Settings
Guide.
❒ Paper within the following dimen-
sions can be set in the bypass tray:
• Vertical: 90 - 297 mm (3.55 - 11.69
in.)
• Horizontal: 148 - 432 mm (5.83 -
17.00 in.)
❒ Be sure to set the paper with the
side you want to print facing down
in the bypass tray.
Limitation
❒ The following functions are disa-
bled when printing from the bypass tray:
• Duplex printing
• Auto Tray Select
• Auto Tray Switching
• Rotating Collate
• Staple (when the optional unit is
installed)
Important
❒ When printing using the printer
function, original images are always rotated by 180 degrees (the
orientation of images to be printed
is opposite to that of the copier
function). When printing onto paper with specific orientation requirements, such as envelopes and
letterheads, make sure to rotate the
paper feed orientation to 180 degrees.
Open the bypass tray.
AAAA
❒ When loading OHP transparencies
or thick paper in the bypass tray,
make the paper setting using the
control panel or printer driver.
❒ The number of sheets that can be
loaded in the bypass tray depends
on the paper type.
❒ Paper sizes fed from the bypass
tray are output first sheet down,
print side-up.
14
Adjust the paper guides to the pa-
BBBB
per size.
Important
❒ If the paper guides are not flush
against the paper, skewing and
misfeeds might occur.
AGP004S
Setting Paper on the Bypass Tray
Gently insert paper face up into
CCCC
the bypass tray until the beeper
sounds.
1.
Extender
2.
Paper guides
Note
❒ The beeper will not sound if it is
turned off. Gently insert paper
until it stops.
❒ Do not stack paper over the lim-
it mark, otherwise a skewed image or misfeeds might occur.
❒ Open out the extender to support
paper sizes larger than A4 L,
1
8
/2"×11" L.
❒ Fan the paper to get air between
the sheets to avoid a multi-sheet
feed.
❒ When setting an OHP transpar-
ency, make sure that its front
and back sides are properly positioned.
AGP005S
Select the paper size.
DDDD
Important
❒ Set the paper size and orienta-
tion using the display panel
when printing on paper from
the bypass tray.
❒ If bidirectional communication
is disabled, set the paper size
and orientation in the bypass
tray using the printer driver, according to the setting made on
the display panel.
Note
❒ Thick paper and OHP transpar-
encies are delivered face up on
the top of the preceding page;
therefore, the prints need to be
rearranged into the correct order. To avoid this, select [Reverse
order print] in the RPCS printer
driver settings to deliver the
prints in the correct page order.
Reference
For printer driver settings, see
the printer driver Help.
For details about setting custom
sizes, see p.16 “Setting custom
size paper”.
A Press the {{{{User Tools/Counter}}}}
key on the control panel.
1
❒ Select paper type when printing
onto OHP transparencies or
thick paper (over 127.9 g/m
For details, see p.17 “Setting
thick paper or OHP transparencies”.
2
).
AEU043S
B Press [System Settings].
15
Getting Started
1
C Press the [Tray Paper Settings] tab.
D Press [TTTTNext
the list.
E Press [Printer Bypass Paper Size].
F Select the paper size.
Note
❒ Press [UUUUPrevious] or [TTTTNext]
to scroll through the list.
❒ When printing onto thick pa-
per or OHP transparencies,
select paper type. For details,
see p.17 “Setting thick paper
or OHP transparencies”.
] to scroll through
Press the {{{{User Tools/Counter}}}} key
AAAA
on the control panel.
Press [System Settings].
BBBB
Press the [Tray Paper Settings] tab.
CCCC
Press [TTTTNext] to scroll through the
DDDD
list.
Press [Printer Bypass Paper Size].
EEEE
Press [
FFFF
If a custom size is already set, press
[Change Size] .
Press [Vertical].
GGGG
Enter the vertical size of the paper
HHHH
using the number keys, and then
press [#].
Custom Size
].
G Press [OK].
H Press the {{{{User Tools/Counter}}}}
key.
Setting custom size paper
Important
❒ Set the paper size and orientation
using the display panel when
printing on custom size paper
from the bypass tray.
❒ If bidirectional communication is
disabled, set the paper size and orientation in the bypass tray using
the printer driver, according to the
setting made on the display panel.
Reference
For printer driver settings, see the
printer driver Help.
Press [Horizontal].
IIII
Enter the horizontal size of the
JJJJ
paper using the number keys, and
then press [#].
Press [OK].
KKKK
The paper sizes entered are displayed.
Press [OK].
LLLL
Press the {{{{User Tools/Counter}}}} key.
MMMM
16
Setting thick paper or OHP
transparencies
Setting Paper on the Bypass Tray
Press the {{{{User Tools/Counter}}}} key
AAAA
on the control panel.
Press [System Settings].
BBBB
Important
❒ Set the paper type using the dis-
play panel when printing on thick
paper or OHP transparencies from
the bypass tray.
❒ If bidirectional communication is
disabled, set the paper type in the
bypass tray using the printer driver, according to the setting made
on the display panel.
Note
❒ Insert OHP transparencies in the
K orientation.
❒ Paper settings can also be set using
the printer driver. The following
procedures are not necessary
when setting paper sizes using the
printer driver.
❒ When the printer driver is not used,
make settings using the display
panel.
Reference
For printer driver settings, see the
printer driver Help.
Press the [Tray Paper Settings] tab.
CCCC
Press [TTTTNext] to scroll through the
DDDD
list.
Press [Paper Type: Bypass tray].
EEEE
Select [OHP] or [Thick Paper]
FFFF
Press [OK].
GGGG
The paper type selected is displayed.
Press the {{{{User Tools/Counter}}}} key.
HHHH
Note
❒ The settings made will remain
valid until they are reset again.
After printing on OHP transparencies or thick paper, make
sure to clear settings for the next
user.
1
17
1
Getting Started
18
2. Preparing the Machine
Quick Install
Windows 95/98/Me/2000/XP, Windows Server 2003, and Windows NT 4.0 users can easily install this software using the CD-ROM provided.
Using Quick Install, the PCL printer driver and/or RPCS printer driver and
SmartDeviceMonitor for Client is installed under network environment, and
TCP/IP port will be set.
Important
❒ To install printer driver under Windows 2000/XP Professional, Windows
Server 2003, and Windows NT 4.0, you must have an account that has Manage Printers permission. Log on as an Administrator.
❒ The Quick Install is not available when using this printer under USB connec-
tion. If you connect using USB, refer to p.43 “Installing the Printer Driver Using USB”.
Quit all applications currently running.
AAAA
Insert the CD-ROM into the CD-ROM drive.
BBBB
The installer starts.
Auto Run may not work with certain operating system settings. If this happens, launch “Setup.exe” on the CD-ROM root directory.
Select an interface language, and then click [OK].
CCCC
The default interface language is English.
Click [Quick Install].
DDDD
The software license agreement appears in the [
After reading the agreement, click [
EEEE
[Next >].
Select the machine model you want to use in the [Select Printer] dialog box.
FFFF
For network connection via TCP/IP, select the machine whose IP address is
displayed in [Connect To].
For parallel connection, select the machine whose printer port is displayed in
[Connect To].
I accept the agreement
License Agreement
] , and then click
] dialog box.
Click [Install].
GGGG
The printer driver installation starts.
19
2
Preparing the Machine
Click [Finish]
HHHH
A message about restarting the computer may appear. Restart the computer
to complete installation.
Click [Exit] in the first dialog box of the installer, and then take out the CD-
IIII
ROM.
Note
❒ To stop installation of the selected software, click [Cancel] before installa-
tion is complete.
❒ Auto Run may not work with certain operating system settings. If this hap-
pens, launch “Setup.exe” on the CD-ROM root directory.
❒ Select a machine to whose IP address is displayed in [Connect To] to install
SmartDeviceMonitor for Client when using TCP/IP.
Reference
Quick Install is not available unless bidirectional communication between
the machine and computer is enabled via parallel connection. See p.60 “If
Bidirectional Communication is Disabled” for details about bidirectional
communication between machine and computer.
20
Confirming the Connection Method
Confirming the Connection Method
This machine supports network and local connection.
Before installing the printer driver, check how the machine is connected. Follow
the driver installation procedure that is appropriate to the connection method.
Network Connection
This machine can be used as a Windows printing port or network printer.
Using this machine as the Windows printing port
Network connections can be established through Ethernet, IEEE 802.11b, and
IEEE 1394 (IP over 1394).
Available ports are determined based on the combination of Windows operating
system version and connection method used.
2
❖❖❖❖ Windows 95/98
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
IEEE 1394 (IP over 1394) None
❖❖❖❖ Windows Me
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
IEEE 1394 (IP over 1394) SmartDeviceMonitor for Client port
ZZZ004S
21
Preparing the Machine
❖❖❖❖ Windows 2000
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
Standard TCP/IP
LPR port
IEEE 1394 (IP over 1394) None
2
❖❖❖❖ Windows XP
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
Standard TCP/IP
LPR port
IEEE 1394 (IP over 1394) SmartDeviceMonitor for Client port
Standard TCP/IP
❖❖❖❖ Windows Server 2003
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
Standard TCP/IP
LPR port
IEEE 1394 (IP over 1394) SmartDeviceMonitor for Client port
Standard TCP/IP
❖❖❖❖ Windows NT 4.0
Connection Method Available Ports
Ethernet/ IEEE 802.11b SmartDeviceMonitor for Client port
IEEE 1394 (IP over 1394) None
Reference
See the explanation of how to install the printer driver for each type of port.
For the SmartDeviceMonitor for Client port, see p.25 “Using the SmartDeviceMonitor for Client Port”.
For the Standard TCP/IP port, see p.34 “Using the Standard TCP/IP Port”.
For the LPR port, see p.36 “Using the LPR Port”.
22
LPR port
Confirming the Connection Method
Using as a network printer
This machine can be used as the Windows network printer, the NetWare print
server, or the NetWare remote printer.
2
ZZZ003S
Reference
See the explanation of how to install the printer driver for each type of network printer.
For the Windows network printer, see p.38 “Using as the Windows Network
Printer”.
For the NetWare print server and remote printer, see p.40 “Using as the NetWare Print Server/Remote Printer”.
23
Preparing the Machine
Local Connection
Local connections can be established via parallel, USB, IEEE 1394 (SCSI print),
and Bluetooth connections.
Windows operating system version determines the available connection methods.
• Windows 95:
2
• Parallel connections
• Windows 98:
• Parallel connections
• Windows 98 SE/Me:
• USB, Parallel, and Bluetooth connections
• Windows 2000:
• USB, Parallel, IEEE 1394 (SCSI print), and Bluetooth connections
• Windows XP:
• USB, Parallel, IEEE 1394 (SCSI print), and Bluetooth connections
• Windows Server 2003:
• USB, Parallel, IEEE 1394 (SCSI print), and Bluetooth connections
• Windows NT 4.0:
• Parallel connections
Reference
See the explanation of how to install the printer driver for each method of
connection.
For the USB connection, see p.43 “Installing the Printer Driver Using USB”.
For the parallel connection, see p.48 “Printing with Parallel Connection”.
For the IEEE 1394 (SCSI print) connection, see p.50 “Installing the Printer
Driver Using IEEE 1394 (SCSI print)”.
For the Bluetooth connection, see p.54 “Printing with Bluetooth Connection”.
24
Loading...