Page 1
Caution
•
Before installing options, the machine should be turned off and unplugged for at least
Duplex Unit Type
7000
F or Machine Code: G080
INSTALLATION GUIDE
(Code: G348)
thirty minutes. Components inside the machine become very hot, and could result in a
burn if touched.
•
When lifting the machine, use the grips on both sides. The machine could break or
cause injury if dropped.
•
It is dangerous to handle the plug with wet hands. Doing this may result in receiving an
electric shock.
•
Before moving the machine, unplug the po wer cord from the outlet. If the cord is unplugged
abruptly , it could become damaged. Damaged plugs or cords can cause an electrical or
fire hazard.
•
The inside of the machine becomes very hot. Do not touch the parts label "hot surface".
Touching a "hot surface" could result in a burn.
•
Do not let go of the duplex rev ersal unit until it is f astened in place. It could f all and cause
injury .
Important
❒
Check the printer nameplate to confirm the model code.
❒
If you want to use the optional paper feed unit at the same time, install the optional paper feed unit first, and then install the duplex unit.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Installing the Duplex Reversal Unit Stand
Check the contents of the box.
Description Q’ty
Stand 1
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Paper Guide 1
Short Screw 1
Long Screws 4
Duplex Reversal Unit 1
Duplex Feed Unit 1
Installation Guide (This sheet) 1
the wall outlet.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Lift the external tray in the direction of the arrow (a), and
then remove (
b
Remove the adhesive tape and packing materials.
Important
Turn off the power, and then unplug the power cable from
❒ Do not remove the adhesive tape holding the auxiliary bar yet.
Remove it in step
❒ Do not remove the adhesive tape holding the cable of the du-
plex reversal unit yet. Remove it in step on Installing the
Duplex Reversal Unit.
Duplex Reversal Unit
on Installing the Duplex Reversal Unit.
Remove the two small covers on the upper left cover of
the printer.
1
Open the upper left cover.
).
ZDJP038J
ZDJP711J
Duplex Feed Unit
ZHXH221J
ZHXH230J
2
Remove the two small covers by pinching and pulling
them in the direction of the arrow.
ZHXH241J
3
Close the upper left cover.
Note
❒ You cannot use the two removed covers.
G348-8600
Page 2
Remove the protective cover on the left side of the printer.
Hold the protective cover by both sides, and while pushing
the left side of the cover (a), open it in the direction of
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
the arrow (
b
), and then remove (c).
Remove the green screwdriver, and then close the front
cover.
Use this screwdriver for all attachment and detachment of screws.
○○○○○○○○○○○○○○○○○○○○○○○○
ZDJP041J
Note
❒ You cannot use the removed protective cover.
Attach the paper guide to the stand. Hold it so that the
right side bends down as shown, and then while gripping
a
lightly (
), insert it into the holes of the stand (b).
ZDJP042J
Insert the claws of the stand into the holes on the left side
a
of the printer (
), and then push down (b).
ZDJP043J
○○○○○○○○○○○○○○○○○○○
Slowly open the front cover by pulling on the two areas on
the left and right.
ZHXH171J
Note
❒ After using the screwdriver, return it to its original position on
the inside of the front cover.
Tighten the four long screws fastening the duplex reversal
unit stand, using provided screwdriver. Fasten in the
order of
This completes the installation of the stand. Next, install the duplex reversal unit.
acbcccd
, as shown.
ZDJP044J
Installing the Duplex Re ver sal Unit
With both hands, hold the duplex reversal unit level, and
then insert the hooks into the groove of the stand. Adjust
the tip of the hooks to the line on the stand, as shown,
and then insert slowly. Do not let go of the duplex reversal
unit ev en after insertion.
ZDJH007J
ZHXH250J
The hooks of the duplex reversal unit clip around the bar inside the groove of the
stand.
Page 3
While supporting the duplex reversal unit, remove the
stopper of the printer’s mounting bracket.
Slowly raise the duplex reversal unit, and then fold it up
to the printer.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
ZDJP046J
This stopper will be used in a later step , so take care not to lose it.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Remove the adhesive tape holdings the cable, and then
connect the cable from the duplex reversal unit to the
While supporting the duplex reversal unit, remove the
upper connector on the back of the printer.
adhesive tape, and then hold the auxiliary bar in front of
the hook on the left side, and then stand it up.
ZDJP047J
This completes installation of the duplex reversal unit. Install the duplex feed
unit after the external tray.
Hook the hole of the auxiliary bar onto the printer’s
mounting bracket.
Install the external tray.
ZDJP050J
ZHXH260J
ZDJP048J
In step , move the auxiliary bar to the position with the perforated line, as
shown.
Hang the auxiliary bar on the far left end, as shown, and
then install the stopper removed in step
ZDJP049J
Make sure the auxiliary bar and stopper are installed in the positions, as shown.
.
1
Stand the external tray, and then insert it from the
left side using both hands.
ZHXH270J
B
Pushing the right edge of the external tray
a
lightly with your finger (
), insert it (b).
ZDJP053J
Page 4
○○○○○○○○○○○○○
C
Lower the external tray toward you.
Fasten the duplex feed unit using a short screw and the
provided screwdriver.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
ZHXH280J
ZHXH310J
Installing the Duplex Feed Unit
Slowly open the front cover by pulling on the two areas on
the left and right.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
ZDJH007J
Slowly open the waste oil bottle in the direction of the
arrow.
Be sure to return the provided screwdriver to its original
position on the inside of the front cover.
This completes installation of the duplex feed unit.
Slowly push back the waste oil bottle in the direction of
the arrow.
ZHXH160J
Slowly close the front cover by pressing the two areas on
the left and right.
ZHXH150J
Holding the duplex feed unit using both hands, place it on
the vertical rail, and then slide it slowly in until it stops.
ZHXH290J
The vertical rail is in the position, as shown.
ZHXH300J
ZDJH041J
Note
❒ After finishing the installation, you can check the duplex unit is
installed properly: Print the configuration page from the "List/Test
Print" menu. If it is installed properly, you will see "Duplex Unit"
appear in the "Options" list. (G080)
❒ If the duplex unit is not installed properly, repeat the procedure
from step
. If you cannot install it properly even after
reinstallation, contact your sales or service representative.
Check for leftover parts. You will not need these.
ZHXH011N
Printed in China Copyright © 2002 G348-8600
Loading...