Rice Lake SCT-2200 Quick Setup Manual

SCT-2200

When settings are complete press until the indicator displays SAVE?. Press to save set up and return to the weigh mode.

Pressing any other key exits the setup and discards changes.

Press and to set decimals and minimum division.
Press , and to set the total capacity of the load cells.
Press , and to set the mV/V sensitivity of the load cell.
Press , and to set the weight value present on the load cell.
Press , and to set the scale capacity.
Quick calibration of zero.
Press , and to set the weight value used for the calibration.
Check the load cell signal in millivolts.

Set the analog output on net or gross weight.
Set the maximum value of the analog output.
Set the analog output when the scale shows zero weight.
Set the minimum value of the analog output.

Set the key to be emulated by the input.

Set the output normal state.
Set the output switching condition.

Enable time to disable the output.
Enable time to enable the output.

Enable or disable the hysteresis.

INPUTS

0 NONE
1 GROS

2 NET
3 PCS

4 GRO.0

5 NET.0

6 MOTI

23 K.PR

25.K.MOD
26 K.C

27.K.ZER

28.K.TAR
29 ERR

DIV.DEC
CEL.CAP
CEL.SEN
DEAD.LD

RANGE

ZERO

WEIGHT

ADC.MVV

AN.OUT

AO ZER

MODE

AO MAX

INP.02

AO MIN

INP.01

OUT.02

OUTPUT

Disabled.
Setpoint for gross weight.
Setpoint for net weight, even with no tare.
Setpoint for pieces.

Gross weight at zero.

Net weight at zero.
Active on instability.

Active when the C key is pressed.

Error indication.

Active when is pressed.

Active when is pressed.

Active when is pressed.

Active when is pressed.

Setpoint for net weight when tare exists.

NO/NC

ONSTAT

RL.IST

ENAB.TM

DELAY

OUT.01

FUNC

1
2
3
4
5
6
7
8

9

10

11

30.NET.T

Optional Analog
Model Parameter

Quick Setup Guide

To enter the setup menu, turn the instrument on and briefly press the mode key ( ) when the software version displays.

Press the print key ( ) in the setup menu to view/select the parameter choices.

The instrument has a default calibration with the following
features:

Capacity = 10,000 kg
Load cell sensitivity = 2.000mV/V

Default Factory Calibration

Divisions = 1

Theoretical Calibration

Use parameters 1,2,3,4 to perform a theoretical calibration.

Use parameters 1,5,6,7 to perform a standard calibration
with a known weight. For parameters 6 & 7, press and

Calibration Using Known Weight

wait for ERNOT, STORE?. Then press to accept.
For parameter 7, apply test weight before pressing .

Setpoint Programming

In the weigh mode, press and hold to access output’s
setpoint programming.

Key Function

In setup: scroll forward through parameters
In numeric input: decreases the digit to be modified

ZERO

In setup: scroll back through the functions
In numeric input: increases the digit to be modified

TARE

In setup: quickly position the first step of a menu
In numeric input: selects the digit to be modified, from

MODE

left to right

In setup: enter into a parameter or to confirm a setting
In numeric input: confirms the entry made

PRINT

Turn the instrument on and off

C

In setup: exit a step without confirming the setting

ON/OFF

In numeric input: clears the present value

November 7, 2018

PN 184974 Rev A

230 W. Coleman St. • Rice Lake, WI 54868 • USA

U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe [phone]

Rice Lake Weighing Systems is an ISO 9001 registered company.

© Rice Lake Weighing Systems Specifications subject to change without notice.

www.ricelake.com

Wiring Diagram

SCT-2200

• VE 12 / 24 Vdc POWER SUPPLY

1. GND 0 Vdc (GND)

2. +Vdc +12 / 24 Vdc

• LOAD CELL RECEPTORS

CELL

:

15. SIG+ SIGNAL +

16. SIG- SIGNAL -

17. SEN+ SENSE +

18. SEN- SENSE -

19. EXC+ EXCITATION +

20. EXC- EXCITATION -

• ANALOG OUTPUT (Analog Option Only)

On current

: On voltage:

10. I+ +20 mA 8. V+ +10 V

11. I- 0 mA (GND) 9. V- 0 V (GND)

Note: the maximum resistance applicable on the output current is 350  and the minimum resistance applicable on the output

voltage is 10 N.

• INPUTS AND OUTPUTS

Outputs (48Vac or 60Vdc, 150mA max):

6. IN1 input 1 3. OUT1 output 1

7. IN2 input 2 4. OUT2 output 2

Input common normally connected to ground. 5. COMOUT

• SERIAL PORT

RS 485

RS 232
RJ-IN 485 Line 12. TX Transmission
RJ-OUT 485 Line 13. RX Reception
Pin 4 = A(+) , Pin5 = 14. GND GND

RJ OUT

IN 2
IN 1

COMOUT

12/24 Vdc

Analog Output

RS-232

Load Cell

CAL

Optoisolated Inputs positive logic (12–24Vdc, 5–20mA max)

output common

B(-)

OUT 1
OUT 2

V

I

• CALIBRATION JUMPER

J1 = close to enable access to the metrological parameters

J1

RJ IN

November 7, 2018

PN 184974 Rev A