Revox Re:source Communicate Module User Manual
of Switzerland
of Switzerland
Dominating Entertainment.
Revox of Switzerland
.
Re:source
Communicate
Module
Server
Version
Communicate Server Re:source
1
Contents
Communicate Module
Installation
Connection
Server cabeling
2 Zone music sever
4 Zone music server
8 Zone music server
Server menu
Server operation
Music selection
Artist selection
Manual selection
Alphabetic selection
Replay options
Album selection
Manual selection
Alphabetic selection
Selection not available?
Genre selection
Select genre
Shuffle mode
Play mode
Playlist selection
Select playlist
Playback functions
Defined track selection
Track scroll selection
Repeat
Shuffle
Cue
Server basic settings
Communicate setup
Zone assignment
Auto Play-Funktion
Technical data
Guarantee
2
3
4
5
5-6
7
8
9
9
10
10
11
11
13
14
14
15
15
17
17
18
18
19
19
20
21
21
22
22
23
23
24
24
24
25
25
Communicate Server Re:source
2
Communicate
Module
The Communicate Module is a
universal audio interface with a
serial communication port, which
can serve up to 4 zones
independently with music in
Multiroom operation.
The Communicate module with
the Server2 software is described
in this manual.
Using this software, it can
support the M37 Music server as
a 2 or 4 zone version as well as
its predecessor, the M57 as a 4
or 8 zone version.
This Communicate Module
enables you to manage you
complete CD collection like the
professionals in the radio studios.
In a matter of seconds, you can
access any album, any artist, any
genre and any of your
customised playlists.
The Communicate Module
delegates your musical wishes
to the Music server and keeps
you constantly up-to-date both
in the Main room and each
Additional room in Multiroom
operation.
Important for Multiroom
You will need to make a change
in the Remote menu if you are
using your Music server in
Multiroom operation and want to
have access to the music
database from each Additional
room.
You will find more information
about this on page 23, in the
Chapter, Server basic settings.
Communicate Server Re:source
3
Installation
The communicate module plugin card has the most modern
technology on it and should be
handled with care.
Before you start to install the
card, the M51 must be switched
off and the power plug must be
removed from the power socket.
Any plug position can be
selected for the Server card,
with the exception of slot 7,
which is reserved for the
Decoder card respectively.
Loosen the two screws with the
TORX screwdriver supplied and
remove the slot blanking plate.
Before removing the
communicate module from its
packaging, make sure that you
are not charged with any static
electricity. This could cause a
damaging power discharge
when you touch the module.
To be on the safe side, you
should discharge any static
from yourself by touching an
earthed metal object such as a
radiator.
Remove the communicate
module from its packaging and
insert it into the slot position,
using the two tracks within the
M51 to guide it into position.
The lettering on the card must
be at the top. Just before the
card is fully inserted, you will
feel a certain mechanical
resistance as the card meets
the M51 contact strip. Push the
card fully home by pushing in
the area where the 2 screw
holes are located and fix it in
place with the two screws.
All further steps needed to
integrate the new module into
the M51 will be carried out
automatically next time the unit
is switched on.
Communicate Server Re:source
4
Connection
RS232 connection
The RS232 communication
interface is connected to the
Music server with a 9-pin, 1:1,
Sub-D cable in all Server
configurations.
Audio connections
The Communicate Module is
designed for a 4 zone Multiroom
system and has therefore, 4
independent audio inputs, one for
each zone.
IN 1 for Zone
IN 2 for Zone
IN 3 for Zone
IN 4 for Zone
In Multiroom operation, all 4
audio inputs have to be
connected to the Music server
with the M37 4 and/or M57 4zone music servers.
With the M37 2-zone version,
the first two audio inputs IN 1
and IN 2 have to be connected.
You will find information about
the corresponding cabling in the
next chapter.
If, on the other hand, the M51 is
operated purely as a hi-fi
system, i.e. without Multiroom
usage with Additional rooms, it
is enough just to connect IN 1
with the M37 Music server.
L
With a fixed installation
however, Revox recommends
assigning all 4 audio inputs as
retrofitting cables can be timeconsuming and expensive.
L IN R
Comm.
RE
V
OX
1
2
3
4
RS 232
Communicate Server Re:source
5
Cabling & Setup
There is different cabling
depending on which Music
server is connected with the
Communicate Module.
Important
Communication between Music
server and Communicate Module
only woks properly if the corresponding Music server has been
selected in the Communicate
Module Setup.
M37 2-Zone Music server
The 2-Zone M37 Music server has 2 audio outputs, which are
connected to the audio inputs 1 and 2 on the Communicate Module.
Audio inputs 3 and 4 are not connected and remain unassigned.
The internal splitting of the music signal to the corresponding zones is
done automatically through a high-quality audio matrix.
L
Zone 1 is connected with the M51 through the source selection. Any
source change at the M51 also affects Zone 1 and vice-versa. You
should take this into acccount with the zone assignment.
Communicate Server Re:source
6
M37 2-Zone Music server
The Communicate Module supports two configurations of the 2-zone
Music server.
2-Zone Server / Zone 12+34
With the Zone 12+34 configuration, the (Additional room) zones 1 and 2
share audio output 1, while zones 3 and 4 share audio output 2. This
means that zones 1+2 hear the same music and so do zones 3+4. Each
zone has the same level of authorisation when it comes to selecting
music.
Select the setting Zone 12+34 as shown below in the Communicate
Module Setup. The Setup menu is called by selecting the Server
source and then pressing the Setup button on the front of the M51 for
about 2 seconds. After this, select the Source softkey.
2-Zone Server / Zone 1+234
With the Zone 1+234 configuration, the (Additional room) zone 1 is
assigned exclusively to the audio output 1, while zones 2, 3 and 4
share the audio output 2.
No Multiroom operation
The setting Zone 1+234 can also be selected if the M51 is used
purely as a hi-fi system, without Multiroom operation. In this case, you
j
ust connect the audio output 1 with the zone input 1. The other audio
connections are not used.
Select the setting Zone 1+234 as shown below in the Communicate
Module Setup.
Communicate Server Re:source
7
4-zone Music server - M37-4 or M57-4
1. Connect the 4 audio cables 1:1 between the Music server and the
Communicate Module.
2. Select the setting Zone 1..4 as shown below in the Communicate
Module Setup. Each of the 4 zones can access the Music server
independently of each other.
The Setup menu is called by selecting the Server source and then
pressing the Setup button on the front of the M51 for about 2
seconds. After this, select the Source softkey.
Loading...