How it Works
Revo
Loading...
RELPTZ22-1
User Manual
44 pgs1.58 Mb0
Table of contents
Loading...

Revo RELPTZ22-1 User Manual

REVO America
1-800-6250-REVO (7386)
User Manual
700 Freeport Parkway Suite 100 Coppell, TX 75019
Model RELPTZ22-1
12 VDC/650 mA NTSC
Publication No. RELPTZ22-10B
REVO America
1-800-6250-REVO (7386)
CAUTION
REVO America wants to ensure that your installation experience is a safe and pleasant one. Please read and adhere to these Safety Instructions.
Never perform any installation procedure or open the camera case with power on.
Model RELPTZ22-1 is an indoor camera and not meant for outdoor use. Doing so will void the warranty.
1. Pay attention to the Warnings and Cautions in the instructions. They are there for your safety and to ensure that the equipment does not get damaged.
2. Do not discard this manual after installation. You may need to reference it in the future.
3. Use a Certified/Listed Class 2 power supply only.
4. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
6. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, DO NOT MODIFY THE PLUG OR OUTLET. Consult an electrician for replacement of the obsolete outlet.
7. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
8. Only use attachments/accessories specified by the manufacturer.
9. Do not submerge the camera in water or any liquid.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, submerged in liquid, does not operate normally, or has been dropped.
Model RELPTZ22-1
700 Freeport Parkway Suite 100 Coppell, TX 75019
REVO America
www.revoamerica.com
RELPTZ22-1
1
FCC Compliance
WARNING
of electric shock.
CAUTION
avoid damage to the equipment or loss of data.
FCC INFORMATION: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursua nt to Part 15 of the FCC rules. T hese limits are desig ned to provide reas onable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Improper operation of this equipment in a reside ntial area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her o wn expens e.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe a est conforme à la norme NMB-003 du Canada.
CE Compliance
WARNING: T his is a Class A product. In a domes tic environment this pr oduct may cause radi o interference in
which case the user may be required to take adequate measures.
The lightning flash within an equilateral triangle is intended to alert the user to the presence of dangerous voltage that may be of significant magnitude to constitute a risk
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating or maintenance instructions that should be noted to
REVO America
www.revoamerica.com
RELPTZ22-1
2
C
o
o
ntt
n
C
Features...................................................................................................................................................... 3
What’s in the Box ....................................................................................................................................... 4
Settings ...................................................................................................................................................... 5
Setting Camera Termination .................................................................................................................. 5
Setting Camera Address ........................................................................................................................ 6
Setting Camera Protocol (Optional) ...................................................................................................... 7
Dimensions ................................................................................................................................................ 9
Installation ................................................................................................................................................ 11
Considerations ..................................................................................................................................... 11
Tools Required ..................................................................................................................................... 11
e
e
ntt
n
s
s
Mounting ............................................................................................................................................... 12
Flush-Mount Installation .................................................................................................................. 12
Surface-Mount Installation ............................................................................................................... 14
Wiring .................................................................................................................................................... 16
Connecting to a Keyboard Controller ................................................................................................. 18
Connecting to a DVR ............................................................................................................................ 19
Camera Configuration ............................................................................................................................. 20
Getting Started ..................................................................................................................................... 20
Understanding the Dome Menu ........................................................................................................... 21
Camera .................................................................................................................................................. 23
Dome Setup .......................................................................................................................................... 27
Specifications .......................................................................................................................................... 36
Troubleshooting ...................................................................................................................................... 37
Glossary ................................................................................................................................................... 38
REVO America
www.revoamerica.com
RELPTZ22-1
3
F
TIP
e
e
att
a
F
• 22X optical zoom PTZ indoor dome came ra
• Superb resolution of 580 lines provides high-quality video day or
night
• High-end features such as Pres e t s, Tours , Auto Scan normally
found in cameras costing thousands m ore
• Built-in motion detection
• Alarm input and output
• Easy-to-use menu system allows setup in minute s
• Wide optical range with PTZ provides coverage of large areas with
just one camera
urr
u
e
e
s
s
• Variable speeds for PTZ func ti ons : Slow, Normal and Turbo enable
you to customize camera opera ti on
• Titling so you can identif y camer a location
Browse the entire manual prior to installing the camera. There is a lot of useful information and tips that will help you to install your system effectively.
REVO America
www.revoamerica.com
RELPTZ22-1
4
Dome Camera
Manual
machine screw PC 4 x 8 (7) and PT plug (8)
• Template sheet for mounting the camera
W
W
h
h
att’’
a
s ii
s
n tt
n
h
h
e
e
B
B
o
o
x
x
•
• Accessory Connectors for Wiring: 2-pin
terminal block (1), 4-pin terminal block and BNC cable (2) and 4-pin terminal block (3)
•
• Accessory Kit: 4 plastic anchors (1), 4
mounting screws PH6 x 35 (2), 4 O-rings (3), safety lanyard (4), machine screw (NPC 2.6 x 6 (5), 3 machine screws PC 2.6 x 6 (6),
REVO America
www.revoamerica.com
RELPTZ22-1
5
S
TIP
NOTE
will be communication errors.
ettttii
S
e
Prior to installing the camera, you must set it up for use in the video system. To do this you will need to access the DIP switches on the bottom of the camera. They are: DOME ID S1 and PROTOCOL S2. Remove the camera from the box and access the DIP switches as shown in Figure 1.
n
n
g
g
s
s
Use a small paper clip to set the DIP switches to ensure that you set each one correctly.
Figure 1. Accessing the DIP Switches

Setting Camera Termination

When you set up your video system, you will be connecting the cameras, keyboard controller and any other devices in a daisy-chain arrangement (m ax i mum o f 4,000 feet ) . All of the devices are set up in a line. The last device in the line must be set so that the control device knows it is the
Setting DIP switches correctly is very important. If you do not set them correctly, there
REVO America
www.revoamerica.com
RELPTZ22-1
6
last device. Set this using DIP switch S2 PROTOCOL (Figure 1). If this camera is to be the last
S2
S2
D1
Terminated
ON
Not terminated
OFF
TIP
NOTE
communication errors.
device, set S2-D1 to ON. If it is not the last device, set S2-D1to OFF.
Set up all of your devices now to ensure that you only have one selected as the last device. Record which device is the last device for future reference.

Setting Camera Address

Each camera requires a unique camera address so that the control device knows which camera is at your back door and which camera is monitoring your driveway. Think of the camera address as a telephone number. In order for the video system to work with multiple cameras, it has to know which one is which.
DIP switch S1 DOME ID (Figure 1) is used to set the camera address. Apply the settings for each camera in your video system as shown in the following table. Up to 255 cameras may be set up. Settings are provided here for eight cameras, either dome or other types. If you are setting up more than 8 cameras, please visit our website at www.revoamerica.com and download our Advanced Features manual RELPTZ22-10AF.
This is an important step. If you do not set the camera addresses correctly, ther e will be
REVO America
www.revoamerica.com
RELPTZ22-1
7
S1 Settings
SWITCH NUMBER
1 2 3 4 5 6 7
8
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
S2
P
OFF
OFF
OFF
F2, RT, Pelco-P, Pelco-D : (Default)
OFF
ON
ON
Pelco-P, Pelco-D
CAMERA
ID

Setting Camera Protocol (Optional)

If you are using a REVO America keyboard controller or not using a keyboard controller at all, and using the camera in the United States or other NTSC standard country, there is no need to change the default settings of DIP switch S2 PROTOCOL (Figure 1). If you need to make changes, see the setting options that follow.
If you are using a keyboard controller or DVR other than REVO America, check the protocol required and set switch S2-D2, D3 and D4 as fo llows:
D2 D3 D4
OFF OFF ON F2, RT
S2 Settings
ROTOCOL
REVO America
www.revoamerica.com
RELPTZ22-1
8
NOTE
Some of the camera features may not be available when using protocols other than the
defaults listed above.
S2
OFF
OFF
2400 bps
ON
OFF
9600 bps : default
To change the BAUD rate to match your keyboard controller, set switch S2-D5 and D6 as follows:
D5 D6
OFF ON 4800 bps
ON ON 19200 bps
BAUD RATE
REVO America
www.revoamerica.com
RELPTZ22-1
9
Dii
D
m
m
e
e
n
n
sii
s
o
o
n
n
s
s
Figure 2. Flush-Mount Case Dimensions
REVO America
www.revoamerica.com
RELPTZ22-1
10
Figure 3. Surface-Mount Case Dimensions
REVO America
www.revoamerica.com
RELPTZ22-1
11
n
TIP
IIn

Considerations

You should carefully consider installation of the camera(s) to ensure a successful and easy installation. The camera may only be used indoors.
Please review the following list prior to starting your installation.
• Camera Location – Cameras should be located in places where they will be protected from direct exposure to the sun, strong light or water immersion. Exposure to any of these will impair video quality and damage the camera.
• Wiring – The cameras are connected to the video system using coaxial cable. They require power from a Class 2 power supply and if you choose to connect alarms or sensors, other wiring. Make sure that you can provide the wiring to the locations that you select, and that power is available for the power supply. Contact REVO America for all the accessories that you will need to install the camera.
• Visibility – The cameras should be mounted so there are no obstructions or blind spots.
• Mounting – The camera should be mounted in a sturdy location capable of supporting its
weight (2.4 lbs; 1.1 kg).
stt
s
allll
a
attii
a
o
o
n
n
If this is your first time installing a video system, you may want to connect all of the

Tools Required

There are no special tools required to install the cam era. Standard flat and Philips head screw drivers, a power drill and power saw may be required to create access for the wiring required for the camera.
cameras and other devices to the DVR prior to installing and mounting the equipment. This will give you the opportunity to wire the system and ensure you have everything connected properly before you mount the cameras and run the wiring.
REVO America
www.revoamerica.com
RELPTZ22-1
12

Mounting

WARNING
NOTE
installing it. See the Wiring section.
Never work with power on. You should always disconnect electrical power prior to
The camera may be flush or surface mounted depending upon your requirement. A flush-mount installation will provide a more compact installation with ceilings where you can easily cut a hole in the ceiling and mount the Camera Set into the ceiling. Surface mounting works better with hard ceilings, where the best solution is to mount the camera Surface Case to the ceiling.
Instructions for installing the camera using either method are provided below.

Flush-Mount Install a ti on

1. Using the supplied template sheet, mark holes in the ceiling for the Camera Set and the anchors that you will secure the camera to the ceiling with the screws. Cut out the hole for the Camera Set and use a suitable sized drill bit or punch to make the holes for the anchors.
installation or removal of any equipment.
Make sure that you run your power, video and signal cabling for the camera prior to
2. Disassemble the Surface Case, Camera Set and Top Case as shown below.
Loading...
+ 30 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use