Revo REHXN0412-1 Quick Installation Guide

REHXN0412-1, Quick Installation Guide

1. Description

This manual applies to the REHXN0412-1 network camera.

The Network Camera provides a network service for a progressive scan image sensor that can be
monitored on a real-time screen regardless of distance or location. By using its dedicated program,
many users are able to access the Network Camer a at once, or a single user can monitor various
network cameras at the same time. It also enables users to play, store and retrieve a monitored image
by using a PC. All the settings and real-time monitoring screens are also provided through web access.

The Network Camera is fully featured f or security surveillance and remote monitoring needs. It is
based on a DSP compression chip, and makes it available on the network as rea l -time, full frame rate
Motion JPEG and H.264 (or MPEG-4) video streams.

The alarm input and alarm output can be used to connect various third party devices, such as door
sensors and alarm bells.

• Installation Steps
Follow these steps to install the network camera on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the Network Camera. See page 3.

3. Set an IP address. See page 4.

4. Set the password. See page 5.

• Package Component

The system comes with the following components:

Network Camera unit Camera Lens Installation CD Installation Guide Accessory Kit Camera stand

• Contents in the installation CD

1. The REHXN0412-1

2. The SmartManager User’s Manual

3. The Revo Remote Pro HD User’s Manual

4. The SmartManager Installation software

5. The Revo Remote Pro HD Installation software

Note: Check your package to make sure that you received the complete system, including all
components shown above.

• Front View

User’s Manual

REHXN0412-1, Quick Installation Guide

• Rear View

NO Function Description

1 Power Adaptor Terminal Main Power, 2pin terminal, DC12V/AC24V 330mA(4.0W)

Power Indicator(Green) Indicates power input.

2

Status Indicator(Red) Indicates camera status.
Audio Input Audio Input Stereo Jack

3

Audio Output Audio Output Stereo Jack

4 Network Connector(PoE) RJ-45 port compatible with 10/100Mbps having PoE functionality.
5 Video Switch Selects Video On/Off. Set to On to output a video signal.

6 Video Output
7 Micro SD Card Slot

3pin Terminal IO Connects alarm In/Out.

8

2pin RS485 Terminal Connects PT device.

9 Reset Button Executes the factory default.

Connects the video output. This BNC connector provides a

1.0Vp-p/75 ohms composite video signal.
Card Slot for Micro SD. Open the protection cover with a
supported tool to insert Micro SD card.

NO Function

1 Focus adjusting fixing screw
2 Auto IRIS lens connector

2

REHXN0412-1, Quick Installation Guide

• LED Indicators

LED Color Indication

Green

Network

Status
Power

Note: Steady green and red during booting. Flash green and red during factory default.

Amber

Unlit No network connection.

Red

Green

Steady for connection to a 100 Mbit/s network. Flashes for
network activity.
Steady for connection to 10 Mbit/s network. Flashes for
network activity.

Steady red for failed upgrade or booting.
Steady green for normal operation or booting.

Flashes green during firmware upgrade.

2. Installation

2.1 Connection

• Connecting to the RJ-45
Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used to connect directly to a PC, while a standard cable is used to connect
to a router or hub.

• Connecting Alarms
AI(Alarm In) :
You can use external devices to signal the network camera to react on events. Mechanical or

electrical switches can be wired to the AI (Alarm In) and G (Gr ound) connectors.
G(Ground) :
Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.
Alarm Out :

The network camera can activate external devices such as buzzers or lights. C onnect the device
to the AO (Alarm Out) and G (Ground) connectors.

• Connecting Video Output

Video Output is used for an easy zoom and focus control when installing the lens. Set Video
Switch to On position to output the video signal. Video Output is restricted to VGA(640x480)
resolution.

Caution: After lens installation, you must set the Video Switch to the Off position to provide the
best performance of the Network Camera.

• Connecting the Power

Connect the power of DC12V or AC24V 330mA for the network camera. Connect the positive(+)
pole to the ‘+’ position and the negative(-) pole to the ‘-‘ position for the DC power.

3