Revo REHVDPTZ22-1 Quick Installation Guide

QUICK INSTALLATION

GUIDE

22X REVO TRAX DOME CAMERA

Model No.:

(DC 12V 1.0A)

REVO AMERICA
700 FREEPORT PARKWAY SUITE 100 COPPELL,
TX 75019 U.S.A TEL.: [phone]-REVO(7386)

Please read this manual thoroughly before use and keep it handy for future reference.

REHVDPTZ22-1

Chapter 1 — Introduction

1.1 Features

The dome camera and the keyboard controller, PC software makes up the building blocks for any
surveillance/security system. Using multiple keyboard controllers and multiple dome cameras, no
place is too large for monitoring. Extensible and flexible architecture facilitates remote control
functions for a variety of external switching devices such as multiplexers and DVRs.

• Built-in optical power zoom camera with True Night Shot function

• Dual video streams simultaneously at full frame rate in all resolutions up to D1 (720X480 in

NTSC, 720X576 in PAL) using Motion JPEG and H.264 (or MPEG-4)

• Intelligent capabilities such as enhanced video motion detection
The encoder’s external inputs and outputs can be connected to devices such as sensors and
relays, enabling the system to react to alarms and activate lights or open/close doors.

• Supports two-way audio

• Logs all user access, and lists currently connected users. Also, full frame rate video can be

provided over HTTPS.

• Interface Protocol: TCP/IP, UDP, IPv4/v6, HTTP, HTTPS, QoS, FTP, SNMP, uPnP, RTP,
RTSP, RTCP, DHCP, ARP

• 120 Preset positions with the individual Camera AE setup

• 4 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with

over 150 functions and Preset locations. While moving, each Preset scan can be watched in
smooth Vector Scan mode.

• 4 Auto Scans with the normal, the vector, and the random mode and the Endless Auto-Pan

with 13 speed steps

• 4 Patterns (up to 200 second) and 4 Privacy Zones

• 8 Area Titles

• 1 Alarm input / 1 Alarm output

• Variable speed from 0.1°/sec to 380°/sec

Three Variable speed (SLOW, NORMAL, TURBO)
Turbo speed is 380°/sec with Ctrl key pressed.

• Pan / Tilt speed is inversely proportional to the zoom ratio with the option.

• Maximum speed is 380°/sec when Preset command.

• Auto Calibration from 0.1° to 6° (Tilt range is 0° to 180°)

• Programmable user preferences (alarm, preset, title, etc.)

• 180° Digital Flip

• Up to 255 selectable camera addresses

• Multi-language Menu Display, Password Confirmation

• Function Run menu using DVR without function key (Pattern, Scan, …)

• Built-in RS-485 receiver driver

• 12VDC for Dome

• Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

2

Chapter 2 — Installation and Configuration

2.1 Package Contents

The dome camera is design to a compact, small size, hard dome camera housing.
The housing is constructed of aluminum, steel and plastic. The housing is designed to be
mounted both wall and ceiling type.
The housing meets the Protection Classification IP66 standards for dust and moisture resistance.

* Dome Camera
* Installation Guide/CD
* Template Sheet
* Mounting Bracket
* Safety Lanyard
* Accessory Kit

1) Mounting screws (PH6 x 35.0)

2) Plastic anchors

3) O-Rings

4) Torx wrench

* Accessory Connector

1) 2Pin Terminal Block

2) 3Pin Terminal Block

3) 6Pin Terminal Block

(4)
(4)
(4)
(1)

(1)
(1)
(1)

1
1
1
1
1
1

1

3

2.2 Installation

The dome camera is for use in surface or pendent mounting applications and the mounting
member must be capable of supporting loads of up to 3.5lb (1.6kg). (Pendent mounting must use
pendent mount accessory.)
The dome camera’s mounting bracket should be attached to a structural object, such as hard
wood, wall stud or ceiling rafter that supports the weight of the dome camera.

CAUTION: A silicone rubber sealant must be applied to seal the housing to secure

waterproofing.

2.2.1 Locking Dome Camera

A. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
B. Fix the Mounting Bracket using Anchors(4x) and Mounting Screws(4x) to the ceiling (Figure B).
C. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
D. Align the locking tap on the bracket and the locking slot on the base of the dome (Figure D).
E. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

4

CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting

screws "A" on the base of the dome camera to best match the mounting
bracket locked position. Unscrew the locking screw on the side of the dome's
base and fit the tab of the mounting bracket into the locking slot. Screws "A"
should not be too tight or too loose when the dome is in the locked position.
After setting the proper positions of screws "A" remove the mounting bracket
and install it to the proper surface. If it is too difficult to lock the dome in
position after the mounting bracket has been installed readjust the screws "A"
by unscrewing them a small amount and try to install dome camera again.

5