REVELL U.S. Army Half-track User Manual [bg, ru, ja, cs, zh, gr, en, ar, ch, da, de, nl, en, es, es, et, he, hi, hr, id, kk, ko, lv, lt, mk, hu, ms, gr, no, fa, pl, pt, pt, ro, sr, sq, sk, fi, sv, th, ch, tr, vi]

This version of the M-3

®

was but one of the many
variants of this versatile
vehicle. These half-tracked
machines were highly re­garded for their excellent
off- road capabilities, and
proved to be high mobile
mounts for versions fitted
with field guns or Howit­zers. The M-3 had a top
speed of 45 mph and
weighed nearly 10 tons!
Your Revell model comes
with a ultility trailer, two
figure and authentic stick­er decals, movable can­non and rolling wheels.

KIT 1744

U.S. ARMY HALF-TRACK

85174410200

* APPLY STICKER

* APPLIQUEZ LES AUTO-COLLANTS

READ BEFORE YOU BEGIN

• CLEAR A SPACE TO WORK ON

• STUDY THE ASSEMBLY DRAWINGS
BEFORE YOU BEGIN

• EACH PLASTIC PART IS IDENTIFIED BY
A PART NUMBER

• DO NOT OVER TIGHTEN SCREWS

• SEE NOTE ABOUT APPLYING
STICKERS IN STEP #8

CAUTION:

POSITION ALL PARTS IN THIS KIT

CAREFULLY. PARTS WILL ONLY SNAP

TOGETHER ONCE.

* REPEAT SEVERAL TIMES

* A REPETER PLUSIEURS FOIS

Á LIRE AVANT DE COMMENCER

• DÉGAGGEZ UN ESPACE POUR

TRAVAILLER.

• ÉTUDIEZ LES ÉTAPES DE MONTAGE
AVANT DE COMMENCER.

• CHAQUE PIÉCE EN PLASTIQUE PORTE
UN NUMÉRO DE PIÉCE.

• NE SERREZ PAS TROP LES VIS.

• LISEZ LA RE MARQUE CONCERNANT
L´APPLICATION DES AUTO-COLLANTS,

´A L´ ÉTAPE 8.

POSITIONNEZ AVEC PRÉCAUTION

TOUTES LES PIÉCES DE CE MODÉLE

RÉDUIT, CAR VOUS NE POUVEZLES

* REMOVE AND THROW AWAY

* A RETIRER ET JETER

MISE EN GARDE:

EMBOîTER QU’UNE SEULE FOIS.

If you have any questions or comments, call our hotline at: [phone]

Revell Inc Consumer Service Department, 1840 Howard Street Unit A, Elk Grove Village, Illinois 60007

Be sure to include the plan number (85174410200), part number, description, your return address and phone number.

Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.

or, please write to:

Visit our website: www.revell.com

Step 1

FENDERS

Step 2

PIVOT

9

GUN

PIVOTS

4

HOLE

FENDERS

Step 3

6

WHEEL

2

SEAT BACK

7

STEERING WHEEL

3

FRAME

SLOTS

TABS

5L

TRACK

6

WHEEL

FENDERS

AND

FRAME

RAISE

GUN

KIT 1744 Page - 1

Step 4

SLOT

BODY

SLOT

Step 5

Step 6

HOLE

FENDERS

AND FRAME

8

PACK

LOCK

RAISE

GUN

10

COVER

TABS

SLOT

SLOT

12

COVER

NOTCH

13

FRAME

14

TRAILER

BODY

NOTCH

TAB

6

WHEEL

KIT 1744 Page - 2

1 2 63

12 46

5

Step 8 Sticker Placement Guide

NOTE: When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly
to lift edge of sticker & use a fingernail to lift sticker from sheet. Line up sticker on body and press an edge into
place, slowly working sticker with a finger nail until sticker is fully on model.

REMARQUE : Pendant l’application des autocollants, éviter de toucher à la face collante pour ne pas laisser d’empreintes.
Plier légèrement la feuille d’autocollants pour relever le bord d’un autocollant, et le détacher de la feuille avec le
bout d’un ongle. Aligner l’autocollant sur la carrosserie, appuyer pour coller un de ses bords, et continuer de
l’appliquer lentement du bout de l’ongle jusqu’à ce qu’il soit complètement collé sur le modèle réduit.

KIT 1744 Page - 3