Page 1
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85118010200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2008. All rights reserved.
F-14 TOMCAT
KIT 1180 85118010200
The Grumman F-14 is an air
superiorty fighter without equal. It
has been proven to be one of the
most maneuverable combat fighters
ever developed. The "Tomcat" utilizes
movable, variable geometry wings
to provide maximum performance
over a broad spectrum of flight
characteristics. The F-14 is equipped
with an array of sophisticated systems
that transforms it into a lethal combat
aircraft.
The F-14 is a two seat aircraft
capable of speeds in excess of Mach
two. The aircraft is powered by two
Pratt and Whitney TF-30 Turbofan
engines that develop nearly 21,000
pounds of thrust each. The "Tomcat"
is 62 feet long and has a wingspan of
61 feet , 10 inches.
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* TRIM
*D´ECOUPER
* OPTIONAL PARTS
* PIECES EN OPTION
* APPLY STICKERS
*APPLIQUEZ LES AUTO-COLLANTS
READ BEFORE YOU BEGIN
• CLEAR A SPACE TO WORK ON.
• STUDY THE ASSEMBLY DRAWINGS
BEFORE YOU BEGIN.
• EACH PLASTIC PART IS IDENTIFIED BY
A PART NUMBER.
• THIS KIT MAY BE SNAPPED TOGETHER BUT PARTS
MAY BE CEMENTED IF YOU PREFER.
• TRIM TO REMOVE EXTRA PLASTIC AND FILE
SMOOTH BEFORE PART ASSEMBLY.
CAUTION:
POSITION ALL PARTS IN THIS KIT CAREFULLY.
PARTS WILL ONLY SNAP TOGETHER ONCE.
• DÉGAGGEZ UN ESPACE POUR TRAVAILLER.
• ÉTUDIEZ LES ÉTAPES DE MONTAGE AVANT DE
COMMENCER.
• CHAQUE PIÉCE EN PLASTIQUE PORTE UN NUMÉRO DE
PIÉCE.
• CETTE MAQUETTE L´ASSEMBLAGE PAR SIMPLE
PRESSION, MAIS VOUS POUVEZ COLLER LES PIECES
SI VOUS LE PREFEREZ.
•
D´ECOUPER POUR ENLEVER LE PLASTIQU SUPERFLU
ET BIEN LIMER DES PI'ECES AVANT L´ASSEMBLAG
MISE EN GARDE:
POSITIONNEZ AVEC PRÉCAUTION TOUTES LES
PIÉCES DE CE MODÉLE RÉDUIT, CAR VOUS NE
POUVEZLES EMBOîTER QU’UNE SEULE FOIS.
Page 2
Step 1
Step 2
Step 3
ASSEMBLED WINGS IN PLACE
NOTE: CAREFULLY SNAP WING RETAINER INTO PLACE, TRAPPING WINGS
AGAINST THE FUSELAGE. MAKE SURE THE WINGS ARE ALIGNED PROPERLY.
A B
Kit 1180 - Page 2
1
st
1
st
1
st
2
nd
2
nd
2
nd
21
WING BOTTOM
4
WING BOTTOM
20
WING TOP
3
WING TOP
1
FUSELAGE TOP
30
WING RETAINER
12
COCKPIT PILOTS
2
FUSELAGE BOTTOM
1
FUSELAGE TOP
Page 3
Step 5
Step 4
MISSILES SHOWN IN PLACE
A
C
B
Kit 1180 - Page 3
14
AFTERBURNER
NOZZLE
REAR OF FUSELAGE
BOTTOM
REAR OF FUSELAGE TOP FRONT OF FUSELAGE TOP
CENTER
OF FUSELAGE
BOTTOM
TOP SIDE IS SHOWN
10
CANARDS
13
MISSILES
24
VERTICAL
STABILIZER
11
VERTICAL
STABILIZER
18
CANOPY
A B
Page 4
5
321415
10
109
6
8 13 9 11
16
15
714912
9
Step 7
Step 6
Kit 1180 - Page 4
17
BASE ARM
16
BASE
NOTE: AFTER SLIDING PART # 17 INTO
PART #16, SLIDE
BACK TO LOCK INTO PLACE.
NOTE: "SWING WINGS" ARE POSITIONABLE. PUT YOUR WINGS
FORWARD FOR TAKEOFF AND BACK FOR SUPERSONIC FLIGHT.
NOTE: INSERT FRONT
HOOK INTO SLOT FIRST.
NOTE: When applying stickers, avoid touching the “sticky” side to prevent finger prints on stickers. Bend sticker sheet slightly to lift edge of sticker & use a finger nail
to lift sticker from sheet. Line up sticker on body and press an edge into place, slowly working sticker with a finger nail until sticker is fully on model.
REMARQUE : Pendant l’application des autocollants, éviter de toucher à la face collante pour ne pas laisser d’empreintes. Plier légèrement la feuille d’autocollants
pour relever le bord d’un autocollant, et le détacher de la feuille avec le bout d’un ongle. Aligner l’autocollant sur la carrosserie, appuyer pour coller un de ses bords, et
continuer de l’appliquer lentement du bout de l’ongle jusqu’à ce qu’il soit complètement collé sur le modèle réduit.
Bonus stickers are included
on the sticker sheet. You
may place them wherever
you like on your model or
wherever you want!
Loading...