Response CWK1 Installation And Operating Instructions Manual

Wired Colour Camera

CCTV Kit

CWK1

Installation and Operating Instructions

These instructions should be retained in a safe place for future reference.

2

INTRODUCTION Section 1

The Response Wired Colour Camera is a colour, weatherproof day/night camera. The

camera easily connects to your TV/VCR/DVR for the protection of your home or office, etc.
The camera is easily mounted on the wall or ceiling using the supplied mounting bracket.

SAFETY AND INSTALLATION TIPS:

Do not attempt to open the camera unit with the power adaptor plug connected to avoid

any risk of personal injury.

When installing CCTV camera(s), always follow manufacturer’s advice when using power
tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety goggles) when
drilling holes, etc. Before drilling holes through walls or ceilings check for hidden electricity
cables and water pipes. The use of a cable/pipe detector is advisable.

When installing this camera, it is advisable to use cable conduit to protect any video/
power extension cables from being exposed externally and to prevent/reduce the chances
of the cables being tampered with. After drilling any hole though an external wall for a
cable, ensure the hole is sealed up around the cable using a sealant to prevent drafts.

To prevent a fire or electrical shock hazard, do not attempt to open the housing while the
unit is exposed to rain, water or wet conditions. There are no user serviceable parts
inside. Refer servicing to qualified service personnel.

NIGHT VISION:

The camera has built-in infra-red LEDs to allow you to view at night for 24hrs

surveillance. The LEDs will automatically activate at night and the picture viewed will
turn to black and white.

Please read before you start:

Always use discretion when installing CCTV surveillance equipment especially

when there is perceived policy. Enquire regarding local regulations applicable
to the lawful installation of video recording/ surveillance. Third party consent
may be required.

3

KIT CONTENTS Section 2

1 xWired Colour Camera

1x10m RCA (male plug ) to RCA (male plug) extension cable
1x12VDC power supply adaptor
1xCamera fixings kit - wall plugs and screws
1xInstallation and operating manual
1xWindow sticker

Tools Required:

Electric drill

5mm masonry drill bit
20mm masonry drill bit
No. 2 Philips screwdriver
3mm flat blade screwdriver

INSTALLATION Section 3

1. Remove the bracket from the camera by unscrewing it from the main body as shown

below:

2. Use the base of the camera’s bracket to mark out the 3 mounting holes on the chosen
surface. Mark out a hole for the cable connectors to pass through into the property
next to the camera.

Note: It is recommended to pass the cable into the property as close to the camera as

possible to reduce the chances of any exposed cables being tampered with. If you

Camera body position

adjustment nut

Unscrew this washer nut to loosen Camera body

from the bracket and unscrew Camera

4

choose to run the cable along the wall outside the property, it is recommended to use
cable conduit to hide the cable and reduce the chances of it being tampered with.

3. Drill 3 x 5mm mounting holes for the bracket’s wall plugs and 1 x 20mm hole for the
camera’s power and video connectors to pass through the wall or ceiling.

4. Install the camera bracket using the supplied plugs and screws.

5. Feed the video/power leads through the hole in the wall or ceiling, starting with the
largest connector, and then refit the camera on to the bracket and adjust the position
of the camera body as required by loosening the adjustment screw.

6. The camera is supplied fitted with a 1m cable terminated with a RCA female plug and
a female power connector.

7. Connect the male end of the power connector from the extension cable into the
camera along with the male RCA connector.

8.

Connect the RCA video end of the extension cable into video input of your TV/VCR/DVR.

9. Tune your TV/VCR/DVR to auxiliary (AUX), A/V or video mode to view the camera.

(Note: Refer to your TV/VCR/DVR’s owner’s manual for setting this up).

10. Adjust the camera again if necessary to the desired viewing angle.

Connection Summary

Note: If the supplied extension cable is not long enough, the extension cable for this

camera can only be extended up to

30m in total length due to power loss.

Extension Cable

12VDC Power

Supply Adaptor

TV / MONITOR

VCR / DVR

Video Signal

to Input

CAMERA

5

TROUBLE SHOOTING Section 4

PROBLEM SOLUTION

No picture can be viewed The power supply adaptor is not plugged in.

The TV/VCR/DVR is not tuned to view the
correct channel.

Poor picture quality Clean the camera lens.

Adjust the contrast/brightness on the TV.

Some colours viewed by The camera’s lens is a CMOS type sensor. Its
the camera do not appear limitation is that it will not produce all colours
to look like true colours viewed outside accurately.

A white image appears The camera’s infrared LEDs shine invisible light.
at night that reflects off surfaces such as glass causing

white light. Place the camera on the other side of
windows or place the lens of camera flush against
the window to try to improve the night vision or
place the camera in a well lit area.

6

TECHNICAL SPECIFICATION Section 5

ITEM WIRED COLOUR CAMERA

Image sensor 1/4” colour CMOS

Video format PAL / NTSC

Pixel resolution PAL: 628 (H) x 582 (V)

NTSC: 510 (H) x 492 (V)

Horizontal resolution 380 TV lines

Minimum illumination 0 Lux when the IR lamps are turned on

Viewing angle 50°

Lens size 6mm

Night vision range Up to 9m

Number of infra-red LEDs 11

IP rating IP54

Operating temperature

-

10°C to 55°C

Power supply 12 VDC / 300mA

Cable type connections Fitted with 1m video cable terminated with female RCA

and female jack (power) plugs

Dimensions (W x D x H) 50 x 50 x 135mm

Weight 280g

7

ACCESSORIES IN THE RANGE Section 6

There are a range of accessories available in the Response CCTV product range to expand

your system:

CA1 2 Channel Digital Video Image Recorder

CA2 LCD Screen for Wireless/Wired CCTV Kits

CWFK1 Wireless Colour Camera CCTV Kit

CA3 Wireless Colour Accessory Camera

(requires CWFK1 CCTV KIT to operate)

CA5 Professional Heavy Duty Camera CCTV Kit

CA6 Dummy Professional Heavy Duty Camera

CA7 4 Channel Digital Video Image Recorder

CA8 Wired Internal Colour Dome Camera CCTV Kit

CA9 Dummy Internal Dome Camera

CA10 Heavy Duty Colour Camera CCTV Kit

CA11 Dummy Heavy Duty Camera

CA4 10m Extension Cable Kit

CA12 20m Extension Cable Kit

DISPOSAL – RECYCLING INSTRUCTIONS Section 7

Directive (2002/96/EC)

This product is classified by the Waste Electrical or Electronic

Equipment (WEEE) Directive. It should not be disposed of with other
household or commercial waste. At the end of its useful life the
packaging and product should be disposed of via a suitable recycling
centre. For information on available facilities, please contact your
local authority or the retailer from where the product was purchased.

GUARANTEE Section 8

Novar ED&S undertakes to replace or repair at its discretion goods (excluding non

rechargeable batteries) should they become defective within 1 year solely as a result of
faulty materials and workmanship.

If the product has not been installed, operated or maintained in accordance with the
instructions, has not been used appropriately or if any attempt has been made to rectify,
dismantle or alter the product in any way the guarantee will be invalidated.

The guarantee states Novar ED&S entire liability. It does not extend to cover consequential
loss or damage or installation costs arising from the defective product. This guarantee does
not in any way affect the statutory or other rights of a consumer and applies to products
installed within UK and Eire only.

If an item develops a fault, the product must be returned to the point of sale with:

1. Proof of purchase.

2. A full description of the fault.

3. All relevant batteries (disconnected).

Response is a trademark of Novar ED&S.

CUSTOMER HELPLINE

Most issues can be solved over the phone in a few minutes.

Please contact our Helpline Team on the number below for any

installation and general advice regarding our products:

0844 736 9149

Lines open 9.00am to 5.00pm, Monday to Friday.

Calls charged at service providers national rate.

Novar Electrical Devices and Systems Limited. (A Honeywell Company)

The Arnold Centre, Paycocke Road, Basildon, Essex SS14 3EA. UK

www.friedland.co.uk

© Novar Electrical Devices and Systems Limited. 2009 50043917 Rev.A