User’s Manual
y
R0E0100TNPFJ00
Converter Board for Connecting R0E001000FLX10 to 100-pin 0.65mm pitch QFP
1. Outline
The R0E0100TNPFJ00 is a converter board for connecting the
flexible cable R0E001000FLX10 to a foot pattern for 100-pin
0.65mm pitch QFP.
2. Package Components (See Figure 1)
Check to see if the R0E0100TNPFJ00 package has all the
following contents before using this product.
(1) R0E0100TNPFJ00 converter board ............................ 1 pc.
(2) YQPACK100RB
(3) NQPACK100RB
(4) YQ-GUIDE
(made by Tokyo Eletech Corporation)................ 1 pc.
(made by Tokyo Eletech Corporation) .............. 1 pc.
(made by Tokyo Eletech Corporation) ......................4 pcs.
(5) R0E0100TNPFJ00 User's Manual (this manual)
3. Specifications
Table 1 Specifications
PRQP0100JB-A:
formerly 100P6S-A
PRQP0100JD-B:
Applicable package
formerly 100P6F-A
PLQP0100JA-A:
formerly 100P6A-A
(100-pin 0.65mm pitch QFP)
Insertion/removal
iterations of connector
50 times
guaranteed
4. Usage (See Figure 2)
The R0E0100TNPFJ00 can be used for debugging and
board-mounted evaluation in common by mounting the
NQPACK100RB on the user system.
(1) For debugging
Mount the NQPACK100RB on the foot pattern of the user
system and attach the YQPACK100RB on it. In addition,
connect the R0E0100TNPFJ00 to the YQPACK100RB,
and then connect the flexible cable R0E001000FLX10 of
the emulator to the upper connector of the
R0E0100TNPFJ00.
(2) For onboard evaluation
Mount an MCU with on-chip flash memory or one-time
PROM and the HQPACK100RB168 (not included) or the
HQPACK100RB1622 (not included) in order on the
NQPACK100RB on the user system.
Use an applicable HQPACK for your package. Check
your HQPACK type number in the user’s manual of the
emulator.
- PRQP0100JB-A (formerly 100P6S-A) package:
HQPACK100RB168
- PRQP0100JD-B (formerly 100P6F-A) package:
HQPACK100RB168
- PLQP0100JA-A (formerly 100P6A-A) package:
HQPACK100RB1622
Before using the R0E0100TNPFJ00, be sure to read the
precautions on page 3.
R0E0100TNPFJ00
converter board
YQ-GUIDE (×4)
Figure 1 Package components of the R0E0100TNPFJ00
(1) For debugging
●: N o.1 p in
Be sure to align the pins.
Figure 2 Usage of the R0E0100TNPFJ00
YQPACK100RB
NQPACK100RB
Flexible cable
R0E001000FLX10
R0E0100TNPFJ00
YQ-GUIDE (×4)
YQPACK100RB
NQPACK100RB
100-pin 0.65mm pitch
foot pattern
REJ10J1735-0200
Rev.2.00
Apr 16, 2010
(2) For on-board
evaluation
HQPACK100RB168
(not included)
or
HQPACK100RB1622
(not included)
FLASH MCU, etc.
* NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK, TQSOCKET, CSSOCKET, CSPLUG/W and
LSPACK are trademarks of Tok
o Eletech Corporation.
REJ10J1735-0200 Rev.2.00 Page 1 of 4
Apr 16, 2010
R0E0100TNPFJ00 User’s Manual
5. Connection Procedure (See Figure 3)
The procedure for connecting the R0E0100TNPFJ00 is shown
below.
(1) Mount the NQPACK100RB on the user system.
(2) Attach the YQPACK100RB on the NQPACK100RB.
(3) Secure the four corners of the YQPACK100RB with the
YQ-GUIDEs.
● Do NOT use the screws included with the
YQPACK100RB for fixing the YQPACK100RB.
● Do NOT use the screwdriver included with the
NQPACK100RB for fixing the YQ-GUIDEs. That is
used only for the HQPACK100RB.
(4) Mount the R0E0100TNPFJ00 on the YQPACK100RB.
(5) Connect the flexible cable R0E001000FLX10 of the
emulator to the R0E0100TNPFJ00.
Flexible cable
R0E001000FLX10
(5)
R0E0100TNPFJ00
Use a slotted screwdriver.
(4)
YQ-GUIDE (×4)
YQPACK100RB
(3)
(2)
(1)
NQPACK100RB
100-pin 0.65mm pitch
foot pattern
●: N o.1 pin
Be sure to align the pins.
Figure 3 Connection procedure of the R0E0100TNPFJ00
6. External Dimensions and a Sample Foot Pattern
42.00
R0E0100TNPFJ00
1
16.50
100
10.27
CN2
5051
1
50 51
Figure 4 External dimensions and a sample foot pattern of the R0E0100TNPFJ00
REV.B
100
CN1
MADE IN JAPAN
7.53
38.00
7.53
2.27
0.35
0.65
19.80
23.20
13.80
17.20
Unit: mm
REJ10J1735-0200 Rev.2.00 Page 2 of 4
Apr 16, 2010
R0E0100TNPFJ00 User’s Manual
7. Precautions and WEEE Directive
CAUTION
Cautions to Be Taken for This Product:
z
When connecting the YQPACK100RB, be sure to use the included YQ-GUIDEs.
z
Do not use the screws included with the YQPACK100RB for connecting the YQPACK100RB.
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
For purchasing the NQPACK100RB, YQPACK100RB, HQPACK100RB168 and HQPACK100RB1622, contact the
z
following:
Tokyo Eletech Corporation http://www.tetc.co.jp/e_index.htm
Disposal Instruction (This is only valid in the European Union.):
Renesas development tools and products are directly covered by the European Union's Waste Electrical and Electronic
Equipment, (WEEE), Directive 2002/96/EC. As a result, this equipment, including all accessories, must not be disposed
of as household waste but through your locally recognised recycling or disposal schemes. As part of our commitment to
environmental responsibility Renesas also offers to take back the equipment and has implemented a Tools Product
Recycling Program for customers in Europe. This allows you to return equipment to Renesas for disposal through our
approved Producer Compliance Scheme. To register for the program, click here “
8. Correspondence of Connectors CN1 and CN2
Table 2 Correspondence of the connectors
CN1 Pin No. IC1 CN1 Pin No. IC1 CN2 Pin No. IC1 CN2 Pin No. IC1
1 - 100 - 1 - 100 2 - 99 - 2 - 99 3 - 98 - 3 - 98 4 - 97 - 4 - 97 5 59 96 58 5 - 96 6 60 95 57 6 - 95 7 61 94 56 7 - 94 8 62 93 55 8 - 93 -
9 63 92 54 9 - 92 10 64 91 53 10 - 91 11 65 90 52 11 - 90 12 66 89 51 12 - 89 13 67 88 50 13 - 88 14 68 87 49 14 - 87 15 - 86 - 15 - 86 16 69 85 48 16 - 85 79
17 70 84 47 17 - 84 80
18 71 83 46 18 - 83 81
19 72 82 45 19 - 82 82
20 73 81 44 20 - 81 83
21 74 80 43 21 - 80 84
22 75 79 42 22 - 79 85
23 76 78 41 23 - 78 86
24 77 77 40 24 - 77 87
25 78 76 39 25 - 76 88
26 - 75 - 26 - 75 27 99 74 38 27 - 74 89
28 100 73 37 28 - 73 90
29 1 72 36 29 - 72 91
30 2 71 35 30 - 71 92
31 3 70 34 31 - 70 93
32 4 69 33 32 - 69 94
33 5 68 32 33 - 68 95
34 6 67 31 34 - 67 96
35 7 66 30 35 - 66 97
36 8 65 29 36 - 65 98
37 - 64 - 37 - 64 38 9 63 28 38 - 63 39 10 62 27 39 - 62 40 11 61 26 40 - 61 41 12 60 25 41 - 60 42 13 59 24 42 - 59 43 14 58 23 43 - 58 44 15 57 22 44 - 57 45 16 56 21 45 - 56 46 17 55 20 46 - 55 47 18 54 19 47 - 54 48 - 53 - 48 - 53 49 - 52 - 49 - 52 50 - 51 - 50 - 51 -
(-:No connection or signals in the emulator)
http://www.renesas.com/weee".
REJ10J1735-0200 Rev.2.00 Page 3 of 4
Apr 16, 2010
1. All information included in this document is current as of the date this document is issued. S uch information, however, is subject to cha nge without any prior notice. Before purc hasing or
A
Notice
using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to
additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website.
2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectu al property rights of third parties by or arising from the use of Renesas
Electronics products or technical information described in this document. No license, express, implied or other wise, is granted hereby under any patents, copyrights or other intellectual
property rights of Renesas Electronics or others.
3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4. Descriptions of circuits, software and o ther relat ed inform ation in this do cument a re pro vided onl y to ill ustrate t he operat ion of semiconductor produ cts and application examples. You are
fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. R enesas El ectronics assume s no responsibilit y for any losses incurred b y
you or third parties arising from the use of these circuits, software, or information.
5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and r egulations and follow the procedure s required by
such laws and regulations. You should not use Renesas Elec tronics products or the technology descri bed in this document for any purpose rel ating to military applications or use b y the
military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technol ogy may not be used for or incorpor ated into any products
or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations.
6. Renesas Electronics has used reasonable care in preparing the information incl uded in this document, but Renesas Electronics does not warrant that such information is error free.
Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
7. Renesas Electronics products are classified according to the f ollowing three quality grades: "St andard", "High Quality", a nd "Specific". The reco mmended applications for each R enesas
Electronics product depends on the product's quality grade, as indi cated below. You must check the quality grade of each Renesas Electronics product before using it in a particular
application. You may not use any Renesas Electronics product for any applicatio n categ orized as " Sp ecific" without the p ri or w ritten cons ent of Renesas Electr onics. Further, you m a y no t
use any Renesas Electronics product for any application for which it is not int ended without the prior written co nsent of Renesas Electro nics. Renesas Electronics shall not be in any way
liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Speci fic" or for which the
product is not intended where you have failed to obtain the prior written consent of Renesas Electroni cs. The quality grade of each Renesas Electronics produc t is "Standard" unless
otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual eq uipment; home electronic appliances; machine tools;
"High Quality": Transportation equip ment (automobiles, trains, ships, etc.); traffic control systems ; anti-disaster systems; anti-crime systems; safet y equipment; and medical equipment
"Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life sup port (e.g. artifi ci al life sup port de vice s or
8. You should use the Renesas Electronics products described in this document within the range spe cified by Renesas Electronics, especiall y with respect to the maximum rating, operating
supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for
malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges.
9. Althoug h Renesas Electronics endeavors to improve the quali ty and reliability of its products, semiconductor products hav e specific characteristics such as the occurrence of failure at a
certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to ra diation resistance design. Please be sure to implement safety
measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the e vent of the failure of a Rene sas Electronics pr oduct, su ch as safety design f or
hardware and software including but not limited to redundancy, fire control and malfunction pre vention, appropriate treatment for aging degradation or any other appropriate meas ures.
Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics s ales office for details as to environmental matters such as the environmental c ompatibility of each Renesas Electronics product. Please use
Renesas Electronics products in compliance with all applicable laws and reg ulations that regulate the inclusion or use of controlled substances, including without limitation, the EU Ro HS
Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the inform ation c ontaine d in this docu ment or Rene sas Ele ctronics pro ducts, or if you ha ve any other
inquiries.
(Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
personal electronic equipment; and industrial robots.
not specifically designed for life support.
systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
7F, No. 363 Fu Shing North Road Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
http://www.renesas.com
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may cause
personal injury or damage to the products.
© 2008-2010 Renesas Electronics Corporation and Renesas Solutions Corporation. All rights reserved.
Renesas Tools Website http://www.renesas.com/tools
ll trademarks and registered trademarks are the property
of their respective owners.
Colophon 1.0
Loading...