As with all electrical appliances, when using your brewer, basic safety precautions should
always be followed:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is used by or around children.
3. To protect against re, electric shock and/or injury, DO NOT immerse cord, plug, or the
brewer unit in water or any other liquid. Do not allow cord to hang over the edge of
the table or counter-top, or touch a hot surface.
4. For best operation, plug the brewer into its own electrical outlet on a dedicated circuit
to prevent ickering of lights, blowing of fuses or tripping of the circuit breaker.
5. Always keep the brewer in its upright position to avoid damaging your brewer.
6. To avoid the risk of injury from extremely hot water, do not open the brewer’s UPPER
JAW while brewing is in process.
7. Keep the WATER RESERVOIR LID on the WATER RESERVOIR at all times, unless
removing to ll with water or clean.
8. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions or has been dropped or damaged in any manner.
9. Do not overll the water reservoir.
10. Use only water in this appliance. Do not put any other liquids or foods in the water
reservoir except as instructed in the CLEANING INSTRUCTIONS section of this guide.
11. Do not touch hot surfaces.
12. To avoid the risk of injury, do not put your ngers inside the brewer’s LOWER JAW area.
This area contains a sharp needle for puncturing the K-Style Cup and could cause you
injury if touched.
13. Turn o and unplug the brewer before cleaning or maintenance. Always allow the
brewer to cool completely before putting on or taking o parts or before cleaning.
14. Do not use harsh cleaners, steel wool pads, or other abrasive materials or cleaners on
the brewer. These type products may damage/scratch the appliance’s surfaces.
15. Do not use outdoors.
16. This appliance is for household use only; do not use the brewer for other than its
intended use/purpose.
Taste | Innovation | Technology
TM
GARANTIES IMPORTANTES POUR LA SÉCURITÉ DU FONCTIONNEMENT
ET DE L’UTILISATION
Comme avec tous les appareils électriques, lorsque vous utilisez votre brewer, les précautions de sécurité de base doivent toujours être suivies:
1. Lire et comprendre toutes les instructions avant utilisation.
2. Une surveillance attentive est nécessaire lorsqu’un appareil est utilisé par ou autour des
enfants.
3. Pour protéger contre les risques d’incendie, de choc électrique et/ou de blessure, NE
PAS immerger le cordon, la prise ou le brasseur unité dans l’eau ou dans tout autre
liquide. Ne laissez pas de cordon pendre de la table ou du comptoir-top, ou touchez
une surface chaude.
4. Pour un meilleur fonctionnement, branchez le brasseur dans sa propre prise de courant
sur un circuit dédié an d’éviter les scintillements des feux, souant de fusibles ou le
déclenchement du disjoncteur.
5. Toujours garder le brasseur dans sa position verticale pour éviter d’endommager votre
Brewer.
6. An d’éviter les risques de blessure de extrêmement l’eau chaude, ne pas ouvrir le
brasseur de mâchoire supérieure tandis que votre café est en cours de traitement.
7. Maintenir le couvercle du réservoir d’eau sur le réservoir d’eau à tout moment, sauf
retrait de remplir avec de l’eau ou de le nettoyer.
8. Ne pas faire fonctionner un appareil avec une prise ou un cordon d’alimentation
endommagé, ou si l’appareil ne fonctionne pas correctement ou est tombé ou a été
endommagé de quelque manière que ce soit.
9. Ne pas trop remplir le réservoir d’eau.
10. Utiliser uniquement de l’eau dans l’appareil. Ne pas mettre d’autres liquides ou
d’aliments dans le réservoir d’eau, sauf comme indiqué dans les INSTRUCTIONS DE
NETTOYAGE section de ce guide.
11. Ne touchez pas les surfaces chaudes.
12. Pour éviter les risques de blessures, ne pas mettre vos doigts à l’intérieur du brasseur de
mâchoire inférieure. Cette zone contient une forteaiguille pour transpercer lek-style
cupet pourrait vous blesser si vous les touchez.
13. Éteignez et débranchez le brasseur avant le nettoyage ou l’entretien. Toujours laisser le
brasseur de refroidir complètement avant de mettre le ou le décollage pièces ou avant
de le nettoyer.
14. Ne pas utiliser les produits agressifs, laine d’acier, plaquettes ou d’autres matériaux
abrasifs ou nettoyants sur le brasseur. Ces produits peuvent endommager/scratch
l’appareil de surfaces.
15. Ne pas utiliser à l’extérieur.
16. Cet appareil est destiné uniquement à un usage domestique; ne pas utiliser le brasseur
pour utilisation autre que son usage/objet.
1
Taste | Innovation | Technology
TM
LET’S GET STARTED!
Unpacking and preparing your iCoee Single Serve Brewer.
Before you can make your rst cup of your favorite beverage, you need to get the
brewer ready to be used:
1. Remove all packing tape, packaging, and stickers from the brewer and wipe clean
with a soft water-dampened cloth.
2. Plug the brewer into a grounded outlet.
3. Place a large cup or mug (10 oz. minimum) on the DRIP TRAY directly below the
JAW area.
4. Remove the WATER RESERVOIR LID from the WATER RESERVOIR, set aside. Remove
the WATER RESERVOIR from the brewer by pulling it straight up from its base.
5. Wash the WATER RESERVOIR & LID with warm soapy water, rinse well and dry with
a soft cloth.
6. Fill the WATER RESERVOIR container with water (tap, bottled or ltered) to the “Max
Fill Line” and then return it back to its base, on the brewer, along with its lid.
7. Press the POWER BUTTON. At this point, the water from the WATER RESERVOIR will
automatically be pumped into the Brewer’s INTERNAL TANK and the water heating
process will begin. This process will take several minutes.
8. Once the water is heated the LCD Screen will read “READY”.
9. Press the “OPEN” ICON the UPPER JAW will automatically raise, at this point
merely press it back down to its original position to close.
10. Turn the DIAL-A-BREW knob until 10 oz is displayed on the LCD Screen, make sure
your mug is in place on the DRIP TRAY and press the “Dial-A-Brew “ knob.
11. The brewer will run the heated water through its components and dispense hot
water into your cup. When the cycle is complete, merely discard the dispensed
water from your cup.
2
Power Button
Power Button
Dial-A-Brew™
Removable 75 oz.
Water Reservoir
Energy save mode
Removable Drip Tray
3
Taste | Innovation | Technology
OPUS Features
B
TM
E
F
G
H
A
C
I
D
J
K
O
N
M
L
A. Water Reservoir
B. Water Reservoir Lid
C. Water Reservoir Lock Tab Slots
D. Housing
E. Upper Jaw
4
F. Removable, Single
Serve Cup Holder
G. Funnel
H. Digital Readout
I. Open Lid Button
J. Drip Tray Plate
K. Drip Tray
L. Energy Saver Button
M. Power Button
N. Dial-A-Brew™ Knob
O. LCD Screen
NOW YOU’RE READY TO BREW YOUR FAVORITE BEVERAGE!
OK, the brewer is on, the LCD Screen reads “READY” and you’re all set to brew a cup of your
favorite beverage, so let’s get started:
1. Place a cup or mug on the DRIP TRAY, press the “OPEN” ICON to release the brewer’s
“UPPER JAW” section, insert your favorite K-Style Cup into the removable SINGLE SERVE
CUP HOLDER, close/lower the UPPER JAW back to its original position.
NOTE: If you want to enjoy a larger cup/travel mug/glass of your favorite brew, merely pull the
DRIP TRAY UNIT (tray and cover) from the brewer towards you and place your larger cup/travel
mug/glass directly below the drip spout.
NOTE: Do not remove the cover from any K-Style Cup. In addition, the SINGLE SERVE CUP
HOLDER has a sharp needle inside the chamber to puncture the K-Style Cup, so to avoid injury
from the needle, never put your ngers in the SINGLE SERVE CUP HOLDER.
2. Turn the DIAL-A-BREW knob until your desired beverage size is displayed on the LCD
Screen.
NOTE: The brewer’s initial ‘brew’ setting is an 8 oz brew. By turning the DIAL-A-BREW knob,
you’ll have the ability to brew between a 4 and 12 oz cup of your favorite beverage and you
can adjust that brew size in 1/2 oz increments. With iCoee’s Single Serve Brewer, you truly
can customize the strength of your favorite beverage! Once you have selected your brew size,
the Brewer will remember that selection.
3. Now, press the DIAL-A-BREW knob to brew your favorite beverage.
NOTE: You’ll notice that the brewer’s LED light in the dispense area will illuminate as your
beverage is being brewed.
CAUTION: The hot water temperature inside the SINGLE SERVE CUP HOLDER is extremely hot,
therefore, never open the JAW areas while brewing, as doing so may result in injury.
4. When the brewer has nished the brew, the LED light in the dispense area will
extinguish. Carefully remove your cup from the DRIP TRAY and enjoy your perfectly
brewed beverage! Careful though, it will be HOT!
5
Taste | Innovation | Technology
TM
NOTE: After brewing a beverage, you’ll notice that the iCoee Single Serve Brewer will
prepare itself for the next brew cycle by pre-heating the water for the next brew. During this
process of pre-heating, you’ll notice that, the LCD screen will read “HEATING”. Once the water
has been heated to the perfect temperature for brewing, the LCD screen will display ‘READY’.
5. Press the “OPEN” ICON to release the “UPPER JAW”, remove the used beverage container
from the SINGLE SERVE CUP HOLDER and discard; careful it will be hot!
HOW TO STOP BREWING IN MID-CYCLE
If you need to stop the iCoee Single Serve Brewer once a brew cycle has started, either
press the POWER BUTTON or DIAL-A-BREW knob to turn o the brewer. NOTE: Stopping a
brew cycle may result in less beverage in your cup the next time you brew.
ADDING WATER
Your iCoee Single Serve Brewer is programmed to alert you, by displaying “ADD WATER” on
the LCD Screen, when you need to add water to the WATER RESERVOIR. You’ll also notice that
the BLUE light in the WATER RESERVOIR will blink. When this occurs, you can ll the reservoir
in one of two ways. Remove the lid from the WATER RESERVOIR and set aside, then either:
- Remove the WATER RESERVOIR from the brewer, ll to the “MAX FILL LINE”, and put it back
onto the brewer and replace the lid, or…
- Leave the WATER RESERVOIR attached to the brewer and merely ll the reservoir with
water to the “MAX FILL LINE” and replace the lid.
CAUTION: Never attempt to remove the WATER RESERVOIR from its base while in the brewing
process. If the WATER RESERVOIR is removed from its base, the brewer may not dispense the
desired amount of liquid.
6
BREWING HOT WATER
iCoee’s Single Serve Brewer is capable of producing hot water for whatever reason you
may choose (Hot chocolate, soup, cooking, etc.). To brew a cup of hot water, press the
“OPEN” ICON to release the UPPER JAW. Then lower it back down to its original position
without adding a K-Style Cup. Place your cup on the DRIP TRAY, select the correct cup size
(4, 6, 8, 10, or 12) and press the DIAL-A-BREW knob.
BREWING ICED BEVERAGES
Craving an iced tea or iced coee… no problem with iCoee’s Single Serve Brewer. Merely
place a tall cup* lled with ice on the DRIP TRAY PLATE, choose your favorite K-Style Cup
(coee, tea or other), insert the K-Style Cup into the brewer as you normally would and
press the DIAL-A-BREW knob. Note: Remember that the ice will melt as your beverage is
dispensed, impacting its strength. To oset this, consider adjusting the DIALABREW KNOB
to a lower number of ounces.
*A special note about the type of cup to use for brewing over ice, never use a cup made of GLASS, the
glass could crack or break when the extremely hot beverage is automatically dispensed over the ice.
PURGING YOUR BREWER
Purging your brewer… what’s that? We’re glad you asked! If you haven’t used your brewer
for a week or so, you probably want to get rid of the old water sitting inside the WATER
RESERVOIR and replace it with fresh water, so… you want to “Purge your Brewer”!
Here’s what to do:
1. Remove the WATER RESERVOIR from the brewer (remove the lid, sit aside, then lift the
water reservoir from its base and the brewer).
2. Discard the water that’s inside the reservoir, rinse it out and then ll it back up with fresh
water.
3. Put the WATER RESERVOIR back on the brewer and replace the lid.
4. Place a cup on the drip tray.
5. Turn the brewer on, press the “OPEN” ICON to release the UPPER JAW then immediately
lower it back down to its original position without inserting a K-Style Cup. When the
brewer tells you it’s ready to brew (i.e. the LCD screen will display “READY”), press
the DIAL-A-BREW knob.
6. Repeat step 5 above until all the water from the WATER RESERVOIR has been depleted,
and the LCD screen displays “ADD WATER”, this will ensure all the old water has been
removed from the brewer’s INTERNAL TANK.
7. Congratulations, you have just purged your brewer of all the old water!
7
Taste | Innovation | Technology
TM
CLEANING AND MAINTENANCE
Cleaning the Brewer’s External Surfaces:
Use a soapy, damp, non-abrasive cloth to clean the brewer’s external surface. NEVER
immerse the brewer in water or other liquids.
The DRIP TRAY and DRIP TRAY COVER are completely dishwasher safe if washed at a low
water temperature in the upper rack; or, you can wash them by hand with a mild detergent.
Cleaning the WATER RESERVOIR, UPPER/LOWER JAWS AND BREWING CHAMBER:
Release the UPPER JAW, remove the SINGLE SERVE CUP HOLDER and wash by hand. The
WATER RESERVOIR and lid should also be washed by hand. Wipe down the UPPER and
LOWER JAW surfaces with a damp non-abrasive cloth, being careful of the needle in the
SINGLE SERVE CUP HOLDER.
UNDERSTANDING AND USING THE ENERY SAVER FEATURE
To help you conserve energy, your brewer has 2 ENERGY SAVING FEATURES, one is
automatic and the other is self initiated. Note the following:
A. AUTOMATIC ENERGY SAVING FEATURE:
The DIAL-A-BREW brewing system automatically enters an energy saving mode
after 2 hours of non-use and will remain in that mode for up to 26 hours. While in
the Energy Saving mode, the brewer remains on but the HOT WATER TANK HOLDING
TEMPERATURE will be reduced. After 28 hours of non-use, the brewer automatically
shuts-o. If your brewer has shut o, due to non-use, merely press the ‘POWER’
button to turn your brewer back on.
B. SELF-INITIATED ENERGY SAVER:
If you would like the brewer to automatically turn o after 2 hours of non-use,
simply press the ‘ENERGY SAVER BUTTON’. When pushed, the ENERGY SAVER
BUTTON will illuminate and the brewer will automatically shut-o after 2 hours of
non-use.
NOTE: If you change your mind and don’t want the brewer to turn o after 2 hours of nonuse, merely press the ENERGY SAVER BUTTON to turn o the feature… and you guessed it,
the ENERGY SAVER BUTTON will no longer be illuminated.
8
DE-SCALING YOUR BREWER:
Over time, tap water mineral deposits may build up in your Brewer. Although non-toxic,
these deposits can hinder the brewer’s performance. Therefore, we recommend that you
de-scale the brewer every 4 to 6 months. If you live in an area with high mineral content in
the water supply, you may want to complete this procedure more often. Do the following:
1. Empty the water out of the WATER RESERVOIR per normal procedures.
2. Fill the WATER RESERVOIR 1/3 full with household white vinegar, then to the MAX FILL
LINE with water. Put the reservoir back onto the brewer and replace its lid.
3. Press the “OPEN” ICON to release the UPPER JAW, then lower it back to its original position.
4. Place a 12 ounce or larger cup size on the DRIP TRAY.
5. Turn the DIALABREW KNOB to the 12 oz cup size.
6. Press the DIAL-A-BREW knob to begin the de-scaling process.
7. Discard the dispensed de-scaling solution from your cup and repeat steps 3 through 6
above until all the solution has been processed through the brewer and dispensed into
your cup.
8. Allow the brewer to sit for at least 4 hours to dissolve all the mineral content.
9. After 4 hours, remove the WATER RESERVOIR from the brewer and wash thoroughly.
10. Fill the WATER RESERVOIR with fresh water to the MAX FILL LINE and return to brewer
along with its lid.
11. Complete steps 3 through 7 above, until all the water has been dispensed through the
brewer and the LCD screen reads “ADD WATER”.
12. The brewer is now ready to make your favorite beverage.
9
Taste | Innovation | Technology
TM
TROUBLESHOOTING ICOFFEE’S SINGLE SERVE BREWERS.
If any problems persist after taking the following action(s), contact Customer Service at
1-661-257-0810 for assistance.
PROBLEM
Brewer doesn’t turn on
ACTION TO TAKE
• Plug brewer into an independent outlet.
• Ensure the brewer is plugged in securely.
• Plug into a dierent outlet.
• Check your circuit breaker and reset if necessary.
PROBLEM
Brewer brews a partial cup
ACTION TO TAKE
• Reposition the WATER RESERVE to make sure it is properly seated on the brewer, then
without using a K-Style Cup, brew a cup of hot water to ensure it is working.
• De-scale the brewer.
PROBLEM
Brewer won’t brew
ACTION TO TAKE
• Ensure you have closed the UPPER JAW and the LCD display reads ‘HEATING’ or ‘READY’.
• If the LCD display reads “ADD WATER”, ensure that the water reservoir is full and in its
proper position on the brewer.
PROBLEM
Blue light is Flashing in WATER RESERVOIR
ACTION TO TAKE
• Indicates the WATER RESERVOIR is low on water. Add more water.
PROBLEM
Brewed Beverage is too light or strong
ACTION TO TAKE
• To obtain a stronger brew, turn the DIALABREW KNOB to a lower number of ounces,
this will reduce the water to beverage ratio. To obtain a lighter brew, turn the DIALA
BREW KNOB to a higher number of ounces, this will increase the water to beverage ratio.
Remember to use the correct cup size to avoid overowing.
10
Please log onto iCoffee.com to register your iCoffee Brewer warranty and
receive the latest news and rewards.
Limited One Year Warranty
Remington warrants that your brewer will be free of defects in materials or
workmanship under normal home use for one year from the date of purchase. It
is recommended that you ll out and return the warranty card enclosed with your
Brewer so that your purchase information will be stored in our system. Remington
will, at its option, repair or replace the Brewer without charge upon its receipt of
proof of the date of purchase. If a replacement Brewer is necessary to service this
warranty, the replacement Brewer may be new or reconditioned. If a replacement
Brewer is sent, a new limited one year warranty will be applied to the replacement
Brewer.
This warranty only applies to Brewers operated in the United States and Canada.
This warranty gives you specic legal rights, and you may also have other rights that
vary from state to state and, in the case of Canada, from province to province.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL
COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY,
EVEN IF FORESEEABLE. Some states or provinces do not allow the exclusion
of limitations of incidental or consequential damages, so the above limitation or
exclusion may not apply to you depending on the state or province of purchase.
Nor does this warranty cover damages caused by services performed by anyone
other than Remington or its authorized services providers, use of parts other than
genuine Remington parts, or external causes such as abuse, misuse, inappropriate
power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS
WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, REMINGTON HEREBY
SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR
ICOFFEE Brewer, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR ANY PARTICULAR PURPOSE. Some states or provinces do not
allow disclaimers of such implied warranties or limitations on how long an implied
warranty lasts, so the above limitation may not apply to you depending on the state
or the province of purchase.
How do I obtain warranty service?
Remington Brewers are high-quality appliances and, with proper care, are intended
to provide years of satisfying performance. However, should the need arise for
warranty service, simply log on to icoffee.com and click on the warranty service link
to obtain an Authorization Return number (ATR) so that we may futher assist you or
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to re-
duce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, 1) the marked electrical rating of the extension cord
should be at least as great as the electrical rating of the appliance; 2) the cord
should be arranged so that it will not drape over the counter top or tabletop where it
can be pulled on by children or tripped over unintentionally.
NOTICE: This appliance has a polarized plug (one blade is wider than the other).
To reduce the risk of electric shock, this plug will t in a polarized outlet only one
way. If the plug does not t full in the outlet, reverse the plug. If it still does not t,
contact a qualied electrician. Do not modify the plug in any way.
DO NOT IMMERSE THE ICOFFEE BREWER
IN WATER OR ANY OTHER LIQUID.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
12
SAVE THESE INSTRUCTIONS.
WARNING: TO REDUCE THE
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
!
WARNING TO USERS AND PARENTS: DO NOT permit
children to use brewer unless there is adult supervision.
Brewer dispenses very hot liquid.
WARNING THIS PRODUCT CONTAINS CHEMICALS
INCLUDING LEAD, WHICH IS KNOWN TO THE STATE
OF CALIFORNIA TO CAUSE CANCER, BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM.
RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE THE
BOTTOM COVER, NO USER
SERVICEABLE PARTS ARE
INSIDE. REPAIR SHOULD BE
DONE BY AUTHORIZED SERVICE
PERSONNEL ONLY.
PRE´CAUTIONS IMPORTANTES
Instructions concernant le cordon court: un cordon d’alimentation court est fourni
pour réduire les risques d’enchevêtrement ou de trébucher sur un cordon plus long.
Si une rallonge est utilisée, 1) les caractéristiques électriques de la rallonge devrait
être au moins aussi grande que la puissance nominale de l’appareil ; 2) le cordon
doit être placé an qu’il ne pende pas du comptoir ou de la table où elle peut être
tirée par des enfants ou faire trébucher.
Avis: Cet appareil possède une che polarisée (une lame est plus large que
l’autre). Pour réduire le risque de choc électrique, cette che s’adaptera dans une
prise polarisée que dans un sens. Si la che n’entre pas complètement dans la
prise, inversez-la. Si elle ne rentre toujours pas, contactez un électricien qualié. Ne
modiez pas la che d’aucune façon.
NE PAS IMMERGER LA CAFETIÈRE ICOFFEE
DANS L’EAU OU TOUT AUTRE LIQUIDE.
CE PRODUIT EST POUR USAGE DOMESTIQUE SEULEMENT.
CONSERVER CES INSTRUCTIONS.
AVERTISSEMENT: POUR RÉDUIRE
MISE EN GARDE
RISQUE D’INCENDIE OU
CHOC ÉLECTRIQUE
NE PAS OUVRIR
!
LE RISQUE D’INCENDIE OU
D’ÉLECTROCUTION, NE PAS ENLEVER
LE COUVERCLE INFÉRIEUR. AUCUNE
PIÈCE RÉPARABLE PAR L’UTILISATEUR
N’EST À L’INTÉRIEUR. RÉPARATION
DOIT ÊTRE EFFECTUÉE PAR UN
TECHNICIEN AGRÉÉ UNIQUEMENT
Mise en garde aux utilisateurs et aux PARENTS : ne sont pas les
enfants de permis d’utiliser brasseur, à moins qu’il n’y a surveil
-
lance d’un adulte. Brasseur distribue liquide très chaud.
ATTENTION, CE PRODUIT CONTIENT DES PRODUITS CHI-
MIQUES, Y COMPRIS LE PLOMB, QUI EST CONNU À L’ÉTAT