REMEHA Avanta Series, Avanta 18v, Avanta 24v, Avanta 12v User Manual

User Guide

Remeha Avanta Range

12v | 18v | 24v

Please ensure that the installer has fully completed the Benchmark Checklist on the inside
back pages of the installation instructions supplied with the product and that you have signed
it to say that you have received a full and clear explanation of its operation. The installer is
legally required to complete a commissioning checklist as a means of complying with the
appropriate Building Regulations (England and Wales).

All installations must be notified to Local Area Building Control either directly or through
a Competent Persons Scheme. A Building Regulations Compliance Certificate will then
be issued to the customer who should, on receipt, write the Notification Number on the
Benchmark Checklist.

This product should be serviced regularly to optimise its safety, efficiency and performance.
The service engineer should complete the relevant Service Record on the Benchmark
Checklist after each service.

The Benchmark Checklist may be required in the event of any warranty work and as
supporting documentation relating to home improvements in the optional documents section
of the Home Information Pack.

Broag Ltd.
Remeha House
Molly Millars Lane
RG41 2QP WOKINGHAM,
Berks.

Tel: [phone]
Fax: [phone]
Internet: uk.remeha.com

www.avantarange.com

E-mail: [e-mail]

© Copyright
All technical and technological information contained in these
technical instructions, as well as any drawings and technical
descriptions furnished by us remain our property and may not be
multiplied without our prior consent in writing.

120578.indd 1 6-3-2009 14:45:49

Remeha Avanta 12v / 18v / 24v

SHORT USER GUIDE

4

230 V

Gas

Gas

230 V

R

62999-110708

1 SAFETY

m Installation location for the boiler!

• Do not store or use any flammable materials, aggressive
substance and/or aerosols near the boiler.

• The installation area must be frost-free.

• The switched spur unit for the boiler must always be acces

sible.

m Water and pipe temperatures!

• The factory setting for the domestic hot water temperature is
55°C; this temperature can be set to 65°C.

• The maximum water temperature in the Avanta Plus can
reach 90°C. This means that pipes and/or radiators can
reach this temperature.

m Can you smell gas? What to do:

• Do not smoke and do not create any flame or sparks.

• Do not use any electric switches.

• Turn off the main gas stop cock.

• Open windows and doors.

• Warn those present and leave the building together.

• Call your gas suppliers / installer once you are outside the

building, TRANSCO tel. [phone].

m Can you smell smoke or flue gases? What to do:

• Switch off the boiler.

• Open windows and doors.

• Warn those present and leave the building together.

• Call your installer once you are outside the building.

2 PROBLEMS WITH BOILER AND/OR CENTRAL HEATING SYSTEM

Error codes – errors which can be resolved by the user

Check gas

valve; gas

valve must

be open, if

necessary

open valve

Press Re-set key

for 3 seconds

Press Re-set key

for 3 seconds

Wait for Recovery;

display shows

boiler functions

Properly

Display shows again

note down the error code and boiler type

and contact your installer

Displayshowserroragain

note down the error code and boiler type

and contact your installer

Wait for Recovery;

display shows

boiler functions

Properly

59970LTGBW7H044

Error codes – errors which have to be remedied by the
installer

If the display indicates a different error code from that
described above, note down the error code and boiler type
and call your installer. Contact your installer also in the event
of a water leak.

2. Disable boiler without frost protection, during longer
periods of non-use

• Switch off the boiler

• Switch off controls

• Isolate boiler at the switch spur unit.

• Turn off the boiler gas tap.

m Drain boiler
If there is a chance that the boiler and system can be effected
by freezing weather conditions contact your installer to
arrange to have the system completely drained down.

LT.AL.W7H.000.224

59970LTGBW7H039

5 ENABLING THE BOILER

59970LTGBW7H040

LT.AL.W7H.000.225 + 59970LTGBW7H042

LT.AL.W7H.000.212

LT.NL.W6H.000.079

• Check that the system is full of water and fully vented.

• Turn on the boiler gas tap.

• Switch on the boiler at the fused spur unit; the boiler will run

the start-up program.

- A display test will briefly appear showing all segments of
the display.

f[ xx software version;
p[ xx parameter version;

- A venting cycle of 3 minutes now follows, the version
numbers will be displayed alternately;

- If no errors occur during this cycle (see section 2 - error

codes), the following will appear in the display;

[0 ; stand-by mode

• Set the controls to on and temperature to the desired level.

The boiler will now automatically start operating.