Regency L676S-NG, L676S-LP1 User Manual

Regency L676-1 Sunrise Gas Fireplace

Model L676S-NG1 L676S-LP1

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 12” W.C. (2.98 kPa)

Manifold Pressure - High 3.5” W.C. (0.87 kPa) 10” W.C . (2.49 kPa)

Manifold Pressure - Low 1.6” W.C. (0.40 kPa) 6.4” W.C (1.59kPa)

Orifi ce Size #37 DMS #53 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

Vent Sizing 5” Inner / 8” Outer 5” Inner / 8” Outer

Approved Venting Systems

Flex Vent Systems: FPI AstroCap™ Flex Vent

Rigid Pipe Vent Systems: Simpson Direct Vent Pro®

Unit Dimensions:

Unit Dimensions Description L676S-1

A Firebox Width w/ Standoff 42-1/2” (1080mm)

B Rear Firebox Width 33-1/8” (841mm)

C Firebox Height 37-3/8” (949mm)

D Height w/ Standoff 45-5/8” (1159mm)

E Unit Depth 24” (610mm)

F Height to Vent 40-3/8” (1026mm)

G Fireplace Opening Height 29-1/16” (738mm)

H Fireplace Opening Width 31-5/8” (803mm)

I Height to Fireplace Opening 3” (76mm)

19,500 BTU/h

(5.71 kW)

29,000 BTU/h

(8.49 kW)

Selkirk Direct-Temp™
Metal-Fab® Sure Seal

21,000 BTU/h

(6.15kW)

26,000 BTU/h

(7.61kW)

L676-1 Sunrise Gas Fireplace

Framing Dimensions:

Framing Dimensions Description L676S-1

J Framing Width 43” (1092mm)

K*** Framing Height*** 45-7/8” (1165mm)*** + Hearth

L Framing Depth 24-1/2” (622mm)

M Minimum Height to Combustibles 56-1/4” (1429mm)

N Corner Wall Length 57-3/16” (1453mm)

O Corner Facing Wall Width 80-13/16” (2052mm)

P Vent Centerline Height 49-1/4” (1251mm)

Q Non-combustible Facing Height 15-9/16 (395mm)

R Gas Connection Opening Height 2” (51mm)

S Gas Connection Height 11-1/4” (286mm)

T Gas Connection Inset 5-3/4” (146mm)

U Gas Connection Opening Width 5” (127mm)

Important: Framing height requires consideration of the hearth

***

depth. Dimension K = K + the thickness of installed hearth.

This manual is intended to be a Sales Reference Guide only.
Do NOT use for actual framing and installation of any unit.
Some specifi cations may change without notice.
You must use the actual manual for exact installation specifi cations.

WARNING

Failure to maintain required clearances is a major cause of chimney related fi res.
Installation of this fi replace must comply with these clearances

Please note: Due to ongoing product development, product appearance and specifi cations

are subject to change without notice.

Non-Combustible Requirements:

(738mm)

Metal

Stud

Material

Non-combustible

3"

(76mm)

47-5/8"

15-9/16"

(392mm)

32-1/16”

(814mm)

Material

Non-combustible

6-7/16"

(163mm)

44-1/2"

(1130mm)

Non-combustible

Material

31-5/8"

(803mm)

29-1/16”

Non-combustible Material

Finished Floor

(1209mm)

L676-1 Sunrise Gas Fireplace

Regency L676-1 Sunrise Gas Fireplace

Finishing Requirements:

Note: All non-combustible facing material should butt up cleanly

to the fl anges around the fi rebox opening.

Rough edges may be visible, from an angle, through the 1/2" gap

behind the faceplate.

To obtain a clean edge, facing material edges may be fi nished

with a J-style trim or metal cornerbead (both materials available
at your local building or hardware outlet) see diagram 2.

Important: Materials used must be NON-COMBUSTIBLE

Important:

A 3/4" gap must be maintained all around the outer edge of

the faceplate and the edge of any fi nishing material thicker than
1-1/4").

This gap is required to facilitate the installation of the faceplate and

to ensure the removal of the faceplate for service access.

3/4"

Finishing Material

(thickness + 1-1/4")

Finishing material such as tile, river rock, etc. must not protrude

beyond the front facing fl anges on all 4 sides of the fi rebox opening.

If material such as brick, stone, etc. extends past the faceplate depth,

when fi nishing around the faceplate, the minimum opening dimension
noted below must be adhered to - to ensure the faceplate can be
removed.

36 -1/4”

34 -9/16”

To accommodate various thicknesses of facing material - the
faceplate is adjustable to a maximum of 1-1/4" and a minimum
of 1/2" .
See chart below.

Finished Facing Thickness Faceplate Adjustment

1/2" Factory Setting

1/2" - 7/8" (or less) Adjusted to + 3/8"

7/8" - 1-1/4" (or less) Adjusted to + 3/4"