Regency HZ33CE, HZ33CE-LP10, HZ33CE-NG10 User Manual

Download

Page 1

HZ33CE Gas Fireplace

Non-combustibl

26-1/16"

(662mm)

NAILING STRIP

2-1/2"

[64mm]

742mm

29-1/4"

Model HZ33CE-NG10 HZ33CE-LP10

Fuel Type Natural Gas Propane

Minimum Supply Pressure 5” W.C. (1.25 kPa) 11” W.C. (2.73 kPa)

Manifold Pressure - High 3.5” W.C. (0.87 kPa) 10” W.C. (2.48 kPa)

Manifold Pressure - Low 1.6” W.C. (0.41 kPa) 6.4” W.C. (1.59 kPa)

Orice Size -Altitude 0-4500 ft. #47 DMS #56 DMS

Minimum Input

Altitude 0-4500 ft. (0-1372m)

Maximum Input

Altitude 0-4500 ft. (0-1372m)

Vent Sizing

Flex Vent Systems: FPI AstroCap™ Flex Vent

Rigid Pipe Vent Systems: Simpson Direct Vent Pro®

16"

407mm

12,000 BTU/h

(3.51 kW)

17,000 BTU/h

(4.98 kW)

4” x 6-7/8” - Flex

4” x 6-5/8” - Rigid

Approved Venting Systems

American Metal Products® Amerivent Direct Security Secure Vent® Selkirk Direct-Temp™ Metal-Fab® Sure Seal

23"

584mm

12,500 BTU/h

(3.66 kW)

15,000 BTU/h

(4.39 kW)

4” x 6-7/8” - Flex

4” x 6-5/8”- Rigid

Header

(steel stud

on edge)

DETAILN

SCALE1:6

2X4HEADER

16"

(406mm)

NAILING STRIP

34-9/16" [878mm]

26"

660mm

29-7/16"

747mm

26-1/16"

(662mm)

543mm

21-3/8"

(76mm)

2-1/2"

[64mm]

29-1/4"

742mm

29-1/4"

742mm

Framing

Description HZ33CE

Dimensions

G Framing Width 35"(889mm)

H Framing Height * 31-3/4" (806mm)

I Framing Rise from Floor 0" (when not using a surround)

2" min (when using Casandra Surround )

3-5/16" min (when using Verona Faceplate)

J * For Finish with

Tile Surround

K Corner Wall Length 38-15/16" (988mm)

L Corner Facing Wall Width 55-1/2" (1410mm)

Framing Depth Vertical Horizontal

22-3/4" (578mm) Vertical Rise

19-3/4" (502mm) Rigid / 16" (406mm) Flex

M Framed Chase Ceiling* 36" (914mm) Rigid 32"

Vent Centerline Height* 30" (762mm) Rigid 26"

Gas Connection Height* 1 1/2" (38mm)

P Gas Connection Inset* 7-3/16" (183mm)

Q Gas Connection Width* 3" (76mm)

* Measured from base of unit.

Floor

Opening for gas

connection

(812mm)

Flex

(660mm)

Flex

Page 2

HZ33CE Gas Fireplace

Close to Ceiling

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this replace and vent system be installed only in accordance with these instructions.

The top, back and sides of the ﬁreplace are deﬁned by

Caution Requirements

standoffs. The metal ends of the standoff may NOT

be recessed into combustible construction.

Fire hazard is an extreme risk

WARNING

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this replace and vent

system be installed only in accordance with these instructions.

Clearance: Dimension Measured From:

A: *Front Floor Clearance (min.)

B: *Sidewall (on one side)

C: *Ceiling (room and/or alcove)

D: Alcove Width

E: Alcove Depth

F: Mantel

G: Mantel Clearances

9" (229mm) Side Opening of Unit

30" (762mm) Top Opening of Unit

84" (1219mm) Sidewall to Sidewall (Minimum)

36" (914mm) Front to Back Wall (Maximum)

12" (305mm)

15-3/4" (400mm)

0" Underside of Unit

From Top Opening of Unit

Flue Clearances

Horizontal - Top 2-1/2"

Horiztonal - Side 1-1/2"

Horiztonal - Bottom 1-1/2"

Vertical (Flex Vent) 1-1/2"

Vertical (Rigid) 1-1/4"

Page 3

MANTEL CLEARANCES

Top View

0-3

Allowable mantel leg projection

6-3/4"

Side opening of Unit

HZ33CE Gas Fireplace

Due to the extreme heat this replace emits, the

mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in the diagram on the right.

Note: A non-combustible mantel may be

installed at a lower height if the framing is made of metal studs covered with a non-combustible board.

Note: Ensure the paint that is used on the mantel

and the facing is "heat resistant" or the paint may discolour.

15-3/4" (400mm)

Mantel Clearances

810

12" (305mm)

7-1/2"(191mm)

0 - 3-1/2" (89mm)

13-3/4"(349mm)

24-1/4"(616mm)

to floor

11-3/4"(298mm)

Top opening of Unit

Drywall

Non-combustible material

3"(76mm)

Standoff

Combustible mantel leg clearances from side of unit as per diagram:

Side View

MANTEL LEG CLEARANCES

Page 4

29-7/16"

747mm

21-3/8"

[542mm]

Combustible Material

Non-combustible Finishing Material (ie. tile)

Non-combustible Material (3-1/2" x 34-9/16")

Finishing Material (ie. tile)

Nailing Strip

-1/2" back from unit face

Combustible Material

Non-combustible

Supplied with Unit

1-1/2

(38mm)

Ensure finished material is brought to lip

HZ33CE Gas Fireplace

FRAMING & FINISHING

1. There are 8 (eight) side nailing strips and one top nailing strip available on the unit. One set of four (4) are for a clean ﬁnish installation, the other set

are for a tile ﬁnish installation as they are set back 1/2" (13mm). The top nailing strip is adjustable to 1/2" (13mm).

2. Bend the required four (4) nailing strips to 90º.

3. Attach top nailing strip with one (1) screw (located at the back of the nailing strip). Adjust to required position, flush or back 1/2" and tighten screw.

Adjustable Top Nailing

Strip

Nailing strip for Clean

Finish (set ush with unit)

Nailing strip for Tile Finish (set back 1/2")

Nailing strip for Clean

Finish (set ush with unit)

1. Frame in the enclosure for the unit with framing material.

Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.

2. For exterior walls, insulate the enclosure to the same degree as the rest of the house; apply vapour barrier and drywall, as per local installation codes.

WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems

3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"

4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply ﬁnishing materials such as tile, slate, etc.

Drywall cannot extend beyond the metal surface of the unit.

5. Tile Finish Option 2: If applying a non-combustible ﬁnishing material (tile,slate,etc) the material can be installed directly onto the metal surface (clean

(Do not insulate the replace itself.)

including, but not limited to: excessive condensation on glass doors, poor ame package, carbon, blue ames etc. These are not product

related issues.

section. Combustible materials can be laid against the side and back standoffs and the stove base.

front) of the unit in the area shown below.

TILE FINISH

Page 5

29-7/16"

747mm

21-3/8"

[542mm]

NO FACING OR

FINISHING MATERIAL

IN THIS AREA

No Combustible

Materials in this Area

33-7/16"

[849mm]

34-9/16" 878mm

2-1/2"

[64mm]

5-3/16"

[132mm]

NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT

3-1/2" [89mm]

29-7/16"

747mm

21-3/8"

[542mm]

J Style trim or metal corner bead may be used to finish edges

No Combustible

Materials in this Area

Combustible

Material

Non-combustible Finishing Material

Non-combustible Material (3-1/2" x 34-9/16")

Finishing Material

Nailing Strip

-flush with unit

Combustible Material

Non-combustible

Supplied with Unit

1-1/2

(38mm)

Ensure finished material is brought to lip

HZ33CE Gas Fireplace

CLEAN FINISH

6. If applying a non-combustible facing it may be installed over the metal surface (clean front) of the unit in the area shown below.

WOOD STUD

1/2" DRYWALL

DO NOT EXTEND DRYWALL ONTO METAL SURFACE OF UNIT.

3-1/2"

NON COMBUSTIBLE BOARD SUPPLIED WITH UNIT

34-9/16"

878mm

33-7/16"

[849mm]

Combustible and Non-combustible Facing and Finishing Materials around unit.

NOTE: The 3-1/2" x 34-9/16" non combustible material supplied with this unit can be replaced if trying to achieve a clean ﬁnish. A large piece of non

combustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.

7. Non-combustible material (ie. tile, slate, etc.) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to, this will assure ease of glass door removal and access to the lower panel.

NOTE: Non-combustible ﬁnishing materials may be of any thickness desired.

[89mm]

NON-COMBUSTIBLE FACING FOR CLEAN LOOK (ie. PAINTED FINISH)

1/2" DRYWALL

Minimum Clearances for Finishing Materials

IMPORTANT FINISHING DETAIL NOTE:

Before placing unit into nal position - it is important to know the total thickness / height of nished hearth (tile, carpet, etc.) The base of the replace, 4 sided faceplate or mantel should be level or higher than the nished hearth height.

Trim materials

Note: All non-combustible facing material should butt up cleanly

Rough edges may be visible from an angle.

To maintain a clean ﬁnished edge - facing material edges

IMPORTANT: Materials used must be NON-COMBUSTIBLE.

to the ﬂanges around the ﬁrebox opening.

may be ﬁnished with a J-style trim or metal cornerbead (both materials available at your local building or hardware store).

Page 6

HZ33CE Gas Fireplace

RIGID PIPE VENTING ARRANGEMENTS

Vertical Terminations

(Propane & Natural Gas)

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using one 90o elbow, with rigid pipe vent systems for Propane and Natural Gas.

• Unit must be raised 1".

• Firestops are required at each oor level and whenever passing through a wall.

• Maintain clearances to combustibles.

• Vent must be supported at o󰀨sets.

Note: Must use optional rigid pipe adapter when using rigid vent systems (Part # 510-994.

Page 7

HZ33CE Gas Fireplace

30” (762mm) / 26” (660mm) when using flex Minimum Height Requirement

Vertical Height (Feet)

Horizontal (Feet)

8"(0.2m)

2 (0.6m)

RIGID PIPE VENTING ARRANGEMENTS

Horizontal Terminations

REGENCY

This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal one

elbow).

Note: Must use optional rigid pipe adaptor (Part # 510-994. when using rigid pipe vent systems. (Refer "Rigid Pipe Venting Systems" Section)

DIRECT VENT SYSTEM (FLEX)

(Propane & Natural Gas)

Minimum

Simpson Dura-Vent Center-Line

A vent guard should be used whenever the termination is lower than the speciﬁed minimum or as per local codes.

Note: Regency

Direct Vent System (Flex) is only approved for horizontal terminations.

• Maintain clearances to combustibles.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each oor level and whenever passing through a wall.

Minimum

Flex Kit Center-Line